These arms add angle to your tie rods and axles. We add in steering stops to prevent oversteering and potentially pulling/damaging the tie rod or axle.
@inthewoodswithchris5 ай бұрын
Excellent Video! Thanks
@SuperATVMedia5 ай бұрын
Thanks for the feedback!
@thomaspeplinski66184 жыл бұрын
Who hangs the brake caliper from the brake line, not good.
@change9293 жыл бұрын
why not? these calipers weigh nothing and that is a poly coated stainless steel line...
@vanblindguy46002 жыл бұрын
Old school automotive rubber lines with big heavy Auto calipers YES do not hang. Stainless lines plus ultra light UTV calipers probably a non-issue. But could certainly tie up just to be safe but probably not critical.
@kevinhollenbeck7503 Жыл бұрын
My kit did not come with castle nuts for the knuckle side of the tie rod end as shown in this video. The tapered stud has holes for the included cotter pins, but instead of castle nuts, they included nylock nuts. I need you to send me the proper castle nuts.
@SuperATVMedia Жыл бұрын
Please give us a call so we can get this resolved, 855.743.3427.
@kevinhollenbeck7503 Жыл бұрын
It would sure be helpful if you would give torque specs for all fasteners!
@SuperATVMedia Жыл бұрын
These will be torqued to factory specs as you are reusing factory hardware. If you have questions on a particular piece, give us a call and we can help! 855.743.3427.
@kevinhollenbeck7503 Жыл бұрын
@@SuperATVMedia These A Arms come with your heavy duty tie rods, that use a new tapered stud to attach the tie rod end to the steering knuckle. So this is entirely different than the factory hardware and should come with its own torque spec.
@hendersonlandworks61583 жыл бұрын
Do you half to use the tie rods? I’ve already have the superatv billet tie rods
@taylorrocks6789 Жыл бұрын
Bud what size are the tirerods I need 19" tire rods for my 800 razor you let me know where I can find them
@SuperATVMedia Жыл бұрын
The rods in this video are about 16". The RZR Turbo S tie rods are 19.5", if that would work. Here's a link to that kit: www.superatv.com/polaris-rzr-xp-turbo-s-heavy-duty-tie-rod-kit
@billyogle33042 жыл бұрын
Is it bad to not put the steering stopper in? I’m running a 32” tire on a rzr xp 4 and it’s already hard to turn around at times. Seems like that would just make it harder.
@SuperATVMedia2 жыл бұрын
You will just need 1 on each side to keep your steering even and to prevent damage from oversteering.
@vanblindguy46002 жыл бұрын
The lower arms are adjustable and the lock nut/bushing ends comes loose in the box. Is there some sort of adjustment that needs to be made? I've watched several of these videos outside of my machine and none seem to cover this???
@angelasuncion8395 Жыл бұрын
use that for your advantage if to add a lift kits
@samanton2393 Жыл бұрын
2019 xp turbo dynamix and just installed these a arms, noticed the steering stop went in on the drivers side but when I removed the boot on the passenger side the steering shaft was much bigger that the drivers side and the steering stop didn’t fit on the shaft. Is this common?
@SuperATVMedia Жыл бұрын
We haven't seen this before. Please give us a call so we can dig in a little more, 855.743.3427.
@dwk70075Ай бұрын
Mine were tight, I heated them up in hot water on the stove and they slipped right on.
@jasonsoutdoorsports86324 жыл бұрын
What’s the purpose of moving the wheels forward? And dose this change the steering geometry?
@doss260144 жыл бұрын
So ppl like me and fit a larger tire size with out scrubbing
@CrumbScum Жыл бұрын
What bumper was on This rzr
@SuperATVMedia Жыл бұрын
This machine is running our SuperATV Low Profile Front Bumper. You can find it here: www.superatv.com/polaris-rzr-xp-turbo-low-profile-front-bumper-1
@miguelaguilar88643 жыл бұрын
There hex castle didnt thread on to my tie rods
@danparaschivoiu86202 жыл бұрын
Aa arms for rear will move the tire 2” rearward?like the front ones?
@wreckboyinc47343 жыл бұрын
Sparta ky offroad spiritual awareness
@djmorgan87833 жыл бұрын
Are there A arms and cvs somebody told me they were made in China
@davidsmith7313 жыл бұрын
Yes China.
@ridered72622 жыл бұрын
What isn't made in China?
@Tractors_and_trees Жыл бұрын
This guy my not be 100% camera ready and that's ok, but when he doesn't know which way to hold a pair of Channel Locks, and lets the brake caliper just dangle, etc. - it shows a lack of mechanical experience. There is also no reason to remove the axles when doing this project. (A machine with a few miles on it won't come apart as easily as this new machine did.) Don't fight something that doesn't need to be touched. It's a pretty simple project, but I did want to see someone else do it before I did mine. Overall, I'm happy with the SuperATV arms and ball joints that I installed on my 2021 RZR Turbo.
@n2rescue3594 жыл бұрын
If only the offered them raw so I can finish them in a different color.
@sabryngibson29443 жыл бұрын
Mfs didn’t gimme no zerks bruh🤦🏻
@SuperATVMedia3 жыл бұрын
Hey Sabryn, Sorry to hear that. Give our sales team a call at 1-855-743-3427 and they can get you squared away.
@ryanbanks61873 жыл бұрын
When making these videos please use someone that knows how to use tools and not make rookie mistakes.