Holley terminator X max step by step install 1996-1998 chevy obs

[@jimmiedjohnson2]

Super helpful prob one of the better explained videos

[@LowLifeYonkes]

Thank you for watching I appreciate it

[@DaBundle]

About to drop this 6.0 on a 4x4 Tahoe 99. Should get this motor here soon. Thanks for tips

[@LowLifeYonkes]

Thanks for watching bro I appreciate it

[@Viejito-zq4em]

Do u need anything extra to keep ur 4x4? my is a 1998 k2500 lq9 6.0 4l80e.

[@LowLifeYonkes]

@@Viejito-zq4em mine is a 2wd but I do know u have to keep ur transfer case and front differential wires

[@DaBundle]

@@LowLifeYonkes agree with the wiring unless is Manuel 4x4

[@jony2660]

2nd) I see for the trans harness you tapped into brake switch/Gauge circuit switch. For the main harness, did you tapped into the same gauge circuit switch or what circuit did you use in your build?

[@jony2660]

Never-mind, i just seen you put both switch powers to the same t tap for the gauges.

[@LowLifeYonkes]

U should separate those 2 triggers I didn’t show that but don’t tie them together

[@jony2660]

How do you feel about using those T Taps, i think you used it for the brake switch. Im only asking because in the instructions manual for the terminator it says “don’t use things like “t-taps”,etc. use proper crimpers/solder and heat shrink.

[@LowLifeYonkes]

I did use them I haven’t had a problem to be honest with you if I do that will be the first place I look 👀 thanks for watching I appreciate it

[@Patrickhp206]

Nice video. I am getting ready to install the same terminator X Max in my 71 Chevelle. I thought the instructions said to NOT connect the trans and ECU switch wire on the same switched power because of fed back power from the trans switch line when the car is turned off...something about not shutting off the injectors. Please correct me if I am wrong just want to hook this thing up right the first time.

[@motivationonpurposebrand2222]

Looking good bro and she sounds good...

[@LowLifeYonkes]

Thanks for the comment bro I appreciate you watching

[@MOY5462]

I bought the holley connector for alternator, how would you wire it…

[@ChrisHess1]

Did you hook up the speedometer to be controlled by the vss output? if so, what wire at the fire wall did you use?

[@LowLifeYonkes]

No I didn’t I did get all the gages to work except the speedo but as you know OBS clusters suck and I will be going with a Dakota Digital most likely

[@antonioayala2046]

Build is looking good boss. Now how did you integrate your stock harness with all of this. What did you leave( for lights,turn signals and windows etc.)and cut? I have an 88 I’m working on and I’m at a standstill with that.

[@LowLifeYonkes]

All I have is all lights work so I left all of that alone I still have abs I left that alone and ac wiring I left alone and very important I left the body harness that goes inside the cab on the passenger side firewall leave it alone everything from the engine came off with the exception of oil sending unit, coolant sending unit, sarter trigger wire everything else got cut out which made my harness much smaller and thin but it looks good

[@antonioayala2046]

@@LowLifeYonkes thanks boss appreciate the feed back. So for your starter you ran that independently as well?

[@LowLifeYonkes]

@@antonioayala2046 the starter trigger wire did become independent after I took out most of the engine sensors but I ran it with the body harness to the passenger side and put heat tape since it goes under the header on the passenger side

[@antonioayala2046]

You wouldn’t happen to have a video on what you left untouched on your stock harness. Looking to trim mine down and wet to he sure not to mess it up.

[@LowLifeYonkes]

@@antonioayala2046 no sorry bro I don’t but I will tell you I went to the junkyard and got a complete stock harness and I fucked that 1 up it was a learning process for me since I hate wiring after learning from my mistakes I had to try again and just took my time and it came out perfect

[@fixitjose9780]

Thanks bro for the help 🤝🏽🤝🏽🤝🏽🤝🏽

[@LowLifeYonkes]

Thank you for watching I appreciate it

[@MOY5462]

Thanks bro how did you run the starter wire?

[@LowLifeYonkes]

Yes I did from the original wire harness that’s why I didn’t show it

[@3rdgenjose699]

What did you end up using for the tach ?

[@LowLifeYonkes]

Nothing right now saving up money for a new cluster

[@miguelarellano1509]

How did you get the fuel gauge to work?

[@LowLifeYonkes]

I replaced the air core motor in the gage cluster and installed a new sending unit and it works

[@miguelarellano1509]

@@LowLifeYonkes ok I’m finishing up with one now but gauge doesn’t work. Haven’t yet figured out why

[@SSstunt1]

What is the grey wire for I have one but doesn’t say where it goes….

[@LowLifeYonkes]

It goes to the brake switch to unlock the converter when u hit the brakes

[@SSstunt1]

@@LowLifeYonkesthank you

[@LowLifeYonkes]

@@SSstunt1 👍🏼

[@chrismcculloch5854]

What’s the length of your serpentine belt lol I got the same set up

[@LowLifeYonkes]

930k6 thanks for watching

[@DannyPantoja-uy4fo]

What is the part number for furl Psi harness extension

[@LowLifeYonkes]

I posted all links to parts in the description box below the video thanks for watching I appreciate it

[@cesartorres7976]

Did you need to hook up your NSS??

[@LowLifeYonkes]

What’s NSS ?

[@cesartorres7976]

Neutral safety switch?

[@LowLifeYonkes]

@@cesartorres7976 no I didn’t my truck was originally a 5 speed and it was already replaced with a drive by cable 700r4 so the only wire you need is for the 1 going to the brake switch so it can unlock the converter when u hit the brakes

[@cesartorres7976]

Thanks for the help bro! I’m also having a bigger problem. I can not get my fuel pump to prime! I wired it the same way you did and not getting anything. The pump was fresh before I did the swap. Is there anything else you did that you may have not shown? Even if you think it’s common sense it would help me out a ton! Thanks again

[@LowLifeYonkes]

@@cesartorres7976 I was having a problem with the pump as well I was using the stock truck relay and it had a bad ground so in my video you can see a white wire on the hood hinge I just ran it behind the relay and it powered up since I have the old engine harness unplugged it had no ground

[@tmjr1986]

Playa. I did mine only thing i regret is haking up the harness thinking i was done. But mine is running owell. Lol. Are you doin ac install

[@LowLifeYonkes]

Yea I’m running ac I did get a complete wire harness from the junkyard from a v8 2wd truck that I tried to use and yea I fucked that 1 up so I had enough practice and then I went at my original v6 stick shift harness there’s a few things that are different but similar but it’s in and working how it should

[@LucasisforOil]

Starter and alternator?

[@LowLifeYonkes]

The starter trigger is the original 1 for the old harness nothing changed there and the alternator watch at 17:31

[@dandub6826]

88-94 tip?

[@LowLifeYonkes]

You had a Question?