🦾🙏🏽🙏🏽

Was your truck previously a TBI system

Then put the ugliest steels on it

Getting this done today! Thank you 🤙

A huge thank You for this work, it was very helpful to me, I just finished soldering, and everything is working as it should, cheers!

inherited my Dads 95 obs planning to restore it to a nice condition, always hated the brake mushiness I see you have other videos on your page posted definitely subscribing you explain things very well

Thanks for the great video! How much clearance did u have between the condenser and cooler after doing this mod? Im wondering if i can fit my aux ac fan between the two after doing this project....

HELLO I HAV A 2007 CHEVY CLASSIC 1/2 TON SHORT BED, ITS A 6 LUG BUT WOULD LIKE TO PUT MY 5 ON 5 RALLY WHEELS OR FIND SOME 6 LUG RALLY WHEELS BUT I CANT FIND ANY THAT WILL FIT MY 2007 ANY SUGGESTIONS PLZ.

2nd) I see for the trans harness you tapped into brake switch/Gauge circuit switch. For the main harness, did you tapped into the same gauge circuit switch or what circuit did you use in your build?

How do you feel about using those T Taps, i think you used it for the brake switch. Im only asking because in the instructions manual for the terminator it says “don’t use things like “t-taps”,etc. use proper crimpers/solder and heat shrink.

What year nbs is that master cylinder for tho?

I’m doing the stock mounts like the ones you did is there a left and right or are they the same when I opened mine up they have the same part number on both one has a L on the back of it does it matter ?

I found the deal you're talking about for thirty five dollars online through youtube

Dope, nice work brotha... my next upgrade for 3 of my vehicles

Option 3 is dope!!

Ay bro, on your e-fan Installation , I’m going to do the same install on my 90 Silverado. 2 questions, Did you use a ground temperature sensor that supposed to be installed on the engine block? And on the fuse box you got, do you have to remove the blue wires or can they be left in but still do what you did for the e-fan switches?

I just got a 94 GMC Sierra and I need to get my brakes fixed I'm doing this instead of the stock one hopefully it gets my brakes working

Is this truck a v8 or v6 ?

Such a huge help been trying to find this exact wiring harness

Mabey you can give me some advice I’m pulling the v6 out of my 1997 and I’m putting a lq4 in it I want to get rid of the computer and abs and just run a Holley term x with the Holley digital dash cluster do you know if they have a harness to run the ac to run the factory ac I just want a clean engine bay the truck won’t be a daily driver so I’m deleting as much stuff as I can so the bay is just inner fenders and engine going for the cleanest look as possible thanks

Nice, clean install. Getting ready to do the same on my 1991 OBS with a 700R4. Don't believe the special fitting that you used for the 4L80e is needed in the 700R4. Realize that you are mocking this up/test fitting, but I would put a grommet in the hole that you drilled for the lines.

Drilling ok this must be the wrong tailgate asst.the other one i saw there no Drilling

19:26 Is it bad for the crank to lay them down on the floor like that if you're reusing it? I remember being a kid and my Dad telling me to never lay down sbc cranks on the floor, always to stand them up, preferably on a block of wood. Just wondering if that still applies to the LS cranks, too. Watching from New Mexico. Good job on the video bro! Thank you for explaining everything. You got a new sub! I just bought a '93 obs Chevy that I'll be eventually doing the same. Keep up the good content! 💯

I have a swb step side 98 4x4 I bought new carpet for, this video will help!

Will this work on my 95 5.7l 1500 obs?

Thanks video Bro 👌

Great shows, a tip on that sway bar end link if you're not already raising it, cut the end link bolt.

Can you leave the bracket for the wiring harness on?

Thanks for sharing.

What if mines don’t have the defroster will work the same???

what vehicle fans from

If I do a 3 inch drop springs am I gonna camber ?

I've replaced brake lines brakes calibers n pads n brakes still go to floor

Would it work for a square body?

What grit sand paper did u use?

How about the model for 1999-2007 they can install on 1989

I just installed mine and it goes down twice as fast. Wondering if it’s a cheaper cylinder because it doesn’t say LS Fab on the side of it. Hoping I didn’t pay $70 and wait on customs for something I could have had for $30 on prime

Awesome video!

I need a new brake booster and want to do this upgrade. Any upgrade on the booster needed or go to my local gm dealer and get a oem one? Amazon "replacements" do not have good reviews on the boosters.

Thanks so much for the simple explanation. I will be doing my 95 suburban the same way with the ABS like your's. Think I have rust in my lines.... so will be flushing them too. God Bless

Love what you guys are doing. Subscribed. Im up in the high desert in cali. Doing the body work on my 89 obs. Do you know of a decent paint guy to shoot the paint by chance? Any help would be much appreciated. Thankyou.

I have that same cold air intake coming from eBay does it work pretty good?

Beautiful work! Think this process will work on 96 impala ? Thank you

I bought the holley connector for alternator, how would you wire it…

Hola amigo i really like your video i have the same truck like yours i when to Dutchman website to order the two axles but they have too many measures and i wondered what measures you used for you truck???

What color or carpet did you choose? I have the same truck!! amazing progress man!

Can you find out what lower radiator hose he used and what radiator ?

Nice video. I am getting ready to install the same terminator X Max in my 71 Chevelle. I thought the instructions said to NOT connect the trans and ECU switch wire on the same switched power because of fed back power from the trans switch line when the car is turned off...something about not shutting off the injectors. Please correct me if I am wrong just want to hook this thing up right the first time.

Did you hook up the speedometer to be controlled by the vss output? if so, what wire at the fire wall did you use?

Hey buddy hows it going. I have a question? I have a '88 obs w" a 5.7 350 and wondering what your thoughts are on getting rid of the charcoal emissions canisty. Will it hurt to delete it? Trying to get rid of anything i can to clean up the engine bay. I deleted my antifreeze over flow and replaced it with a tall boy american flag Bubweiser can.