Home Networking Upgrade - 10Gb Fiber, UPS, CAT6 Gigabit - ULTRA CLEAN NETWORK PANEL SETUP

I upgraded the Home Networking Panel and included some great new gear! 10Gb network switch with a Mikrotik CRS305-1G-4S+IN MM Fiber networking switch geni.us/goNi9C and a TP-LINK 16 port Gigabit TL-SG116 geni.us/tplink-16port-TL-SG116 for my Cat 6 Cable Matters 12-Port Patch Panel. The household IoT provided by our Smart Hub and our backup GL.inet AR-150 are also installed. This all is inside the Leviton 42" Structured Media Center 47605-42N with the hinged door 47605-42S for the primary cabinet. The Battery Backup UPS is in a 14" Leviton 47605-140 with Cable Matters 16 AWG 1' extension cables.
Insane Homelab Networking video • INSANE Homelab Network...
👇FEATURED GEAR (#ad)👇
Mikrotik CRS305-1G-4S+IN Fiber Networking Switch geni.us/goNi9C
TP-LINK 16 port Gigabit TL-SG116 geni.us/tplink-16port-TL-SG116
42" Leviton 47605-42N Structure Media Enclosure geni.us/leviton_47605-42N
+ Hinged Door 47605-42S geni.us/leviton_47605_42S
14" Leviton 47605-140 geni.us/leviton_47605_140_smc
Cat 6 Cable Matters 12-Port Patch Panel geni.us/CM_ULMini12port_panel
Smart Home Hub geni.us/AeotecSmartHomeHub
Cable Matters 16 AWG 1' extension cables geni.us/CM_16AWG_1ftextcord
Chapters
0:00 How to Install gear in a Network Panel
0:38 Hardware to install
2:35 Cable Management in Network Panel
3:30 RG-6 Coax Cable Routing
8:13 Installing Leviton 47690-8C2 1 X 8 VIDEO SPLITTER
11:46 Installing TP-Link TL-SG116
13:46 How To mount gear without brackets network panel
15:30 Install Smartthings Hub Network Panel
16:15 Install AR-150
17:05 Install 10Gbit in Network Panel
17:59 DIY Fiber Optic Spool Network
24:40 Network Panel UPS Battery Backup
27:35 Network Panel Cable breakout
👇NETWORKING + HOMELAB GEAR (#ad)👇
RACK - StarTech 42U Rack geni.us/42u_Rack
SERVER RAILS + CABLE MANAGEMENT
APC Server Rails geni.us/APC-SERVER-RAILS
Cable Zip Ties geni.us/Cable_ZipTies
Monoprice 1U Cable Mgmt geni.us/Monoprice_1UCableMgmt
Cable Mgmt Tray geni.us/ServerRackCableMgmt
Dymo Label Maker geni.us/DYMO_LabelMaker
👇HOMELAB GEAR (#ad)👇
RACK - StarTech 42U Rack geni.us/42u_Rack
DISK SHELF (JBOD) + CABLE
Netapp ds4246 geni.us/netapp_4246_caddies
Netapp ds4243 geni.us/netapp-ds4243-wCaddy
QSFP to 8088 (SAS Cable needed for 4246 & 4243 JBODs) geni.us/mCZCP
HARD DRIVES shop.digitalspaceport.com
RAM
DDR4 RAM geni.us/DDR4_ECC_8x32GB
WORKSTATION
HP Z440 geni.us/HP-Z440
HP Z420 geni.us/HPZ420
SERVER
Dell r730 geni.us/Dell_Poweredge_r730
Dell r720 geni.us/OAJ7Fl
Dell r720xd geni.us/5wG9n6
Dell t620 geni.us/dell_t620_256gb
SERVER RAILS + CABLE MANAGEMENT
APC Server Rails geni.us/APC-SERVER-RAILS
Cable Zip Ties geni.us/Cable_ZipTies
Monoprice 1U Cable Mgmt geni.us/Monoprice_1UCableMgmt
Cable Mgmt Tray geni.us/ServerRackCableMgmt
Dymo Label Maker geni.us/DYMO_LabelMaker
HBA
LSI 9207-8e geni.us/LSI-9207-8e
ENCLOSURE
Leviton 47605-42N geni.us/leviton_47605-42N
SWITCH
Dell 5548 Switch geni.us/Dell_5548
Mikrotik crs305 geni.us/goNi9C
Mellanox sx6036 Switch geni.us/Mellanox_SX6036
Brocade icx6610 Switch geni.us/Brocade_ICX6610
UPS
Eaton 9PX6K geni.us/Eaton9PX6K
Eaton 9PX11K geni.us/Eaton9PX11K
Be sure to 👍✅Subscribe✅👍 for more content like this!
Join this channel to get Store discounts + more perks www.youtube.com/@digitalspace...
Shop our Store (receive 3% or 5% off unlimited items w/channel membership) shop.digitalspaceport.com/
Please share this video to help spread the word and drop a comment below with your thoughts or questions. Thanks for watching!
☕Buy me a coffee www.buymeacoffee.com/gospaceport
🔴Patreon / digitalspaceport
🛒Shop
Check out Shop.DigitalSpaceport.com for great deals on hardware.
DSP Website
🌐 digitalspaceport.com
Disclaimers: This is not financial advice. Do your own research to make informed decisions about how you mine, farm, invest in and/or trade cryptocurrencies.
*****
As an Amazon Associate I earn from qualifying purchases.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Other Merchant Affiliate Partners for this site include, but are not limited to, Newegg, Best Buy, Lenovo, Samsung, and LG. I earn a commission if you click on links and make a purchase from the merchant.
*****
#homelab #homenetwork #mikrotik

[@S7EVE_P]

I think the end result, visually at least, is pretty neat although those velcro attachments spoil the look a little. But I'm not a fan of these wall systems, I prefer a cabinet and rack mount components.

[@cherianphilip4707]

It saves space, most people don't have enough of it

[@BulldogsGaming-oc4ro]

Looking super clean and ascetic! If you have cable service over the Coax like MoCA or ISP runs over the coax Please don't use those 8 way splitters people or any 3rd party MoCA splitter. If it's truly being used as antenna you're good. If it's a cable service those 8 ways take too much signal off and will screw your service up. -Cable Tech

[@DigitalSpaceport]

Yeah its all antenna. I ran cat6 and MM fiber in the house so no need to moca.

[@timo4040]

nice job!!! I loved watching you do this project

[@DigitalSpaceport]

Thank you! 😊

[@electronicparadiseonline2103]

Nice job sir. I love watching someone else install network cables and infrastructure. That means I don't have to do it. lol

[@DigitalSpaceport]

Racks are next. I looked up some of the gear I have and I am totally using it wrong in there lol.

[@thejpkotor]

Nice little setup, you may want a wall mounted rack down the line if you need a bigger switch, etc.

[@DigitalSpaceport]

The video on the 3 racks and their networking gear is being edited right now. This panel is just the demark for the house internal network + workbench and the racks.

[@PWingert1966]

I 3-D printed a circular fiber coil support frame at my local public library based on a fiber storage tray that I had found the manual and specs for. Built it in Tiny Cad with tabs that snapped on to split mounting posts with an edge on the bottom to lock them in place. They could rotate out to hold the fiber cable on a 4" circular frame with a cross member for mounting. Again, 3M command strips placed it in the cabinet and on the cross brace hold it nice and secure.

[@DigitalSpaceport]

do you happen to have that uploaded as an stl file?

[@PWingert1966]

@@DigitalSpaceport I don't. The setup seemed specific to my application at the time. The design is easy enough. A two-inch diameter ring with a 2.5mm width. four holes for threaded inserts for the tabs. The tabs themselves are 5mm with a hole at one end to mount the bolts. To mount the ring, I put a couple of flanges with holes on the bottom of the ring for more bolts and I used more threaded inserts on the mounting surface. finding the threaded inserts in that size was the hard part. you could just thread the holes and put the bolts in directly. You could also just use screws in the flanges to secure it if you were mounting to wood for example. I just mimicked the fiber routing in a fibre storage cabinet I found drawings for online. Most of those companies also provide AutoCAD elements of their products you could use as a starting point.

[@PWingert1966]

I use 3M command strips instead of Velcro. They hold extremely well and can be removed by pulling on their tab until the adhesive releases. I attach one side to the back of the device and the other side to the cabinet. then just press the two together and you're done. The adhesive takes a few minutes to set up, so I usually give the two parts a few minutes till I connect them together. They have a wide variety of attachment fixtures for all sorts of things like large, framed pictures, posters, coax wire and mops and brooms. They are a premium product and priced that way but give a clean appearance without the bondage strapped down look. No drilling and they are rated for a variety of weights up to about 10 lbs. or more. Velcro has an industrial version of the product as well. very stiff posts locking against each other. They are rated for up to 20 lbs. But the Velcro is permanently fixed to the surface. and not removable. You can find them in dollar stores, hardware stores, Walmart, and Amazon. There can be peel-away issues with drywall and painted surfaces if the weight is high. The command strips would have solve4d you are mounting issue on the 4-port Mikrotik switch with no effort..

[@lwakefield08]

As a former cable technician it’s nice to see that you are utilizing 75ohm terminators. Question do you have a 7/16? Just seeing you tightening them down with those wire strippers at 10:26 was painful to watch. Great video otherwise!

[@SirHackaL0t.]

Love the layout. Just wondered why you didn’t put the dust caps on the fibre ends when they were unplugged. It helps keep them clean, especially having seen what you did to the first one after wrapping it around the frame. 😱

[@DigitalSpaceport]

I have piles of these from a server room cleanout and agree I should have used the caps, but I lost them long ago. Realistically if there was a problem I would just use the old to pull a new line in (its all in conduit) but all these strands are running w/o errors so 🤷 and finding those caps is a lost cause at this point

[@stanbaldwin7993]

Nice setup!

[@DigitalSpaceport]

Thanks appreciate it

[@paulm7267]

First of all, nicely done. Seriously, short of going to a 19” rack, that is one of the cleanest installs of that many pieces of equipment I have seen in a home. My only feedback is there are multiple reasons to straight up get rid of that 12-way punchdown block and to just terminate those 6 cables in RJ45 connections: (1) you don’t have hundreds of wires to punch down, so there is no an actual benefit (time, space, etc) to using punchdown with only 6 cables. Also, the 12-way punchdown is half unused and wasting space. Terminating in RJ45 is not hard. (2) removing the punchdown block frees up a lot of space by removing a big object out of the cabinet. (3) going with RJ45 terminations allows you to move the switch to either the place where the punchdown is located or even lower, providing you with more options for overall layout. (4) Removing connection/interfaces inherently increases reliability. Those 6 could go straight into the switch. (5) In the future, if you want to move to 5Gbe or 10GBe with those cables, the punchdown doesn’t have the necessary shielding that you get with the appropriate RJ45 connector. (6) People need to stop using punchdowns for essentially nostalgia purposes. It’s old tech, not shielded. I feel too many people use them because they see them in older installations or at work and are coping it without questioning if it is necessary.

[@chrisharvie-smith486]

Putting wireless radio devices in a closed metal box seems like a bad idea for them to work. Shouldn't they be in the center of the house for best range ?

[@paulherman5198]

Not a bad little setup. I would have tried to trim the fiber up a bit. You might be able to 3D Print some more mounts and such for the box to clean it up nicely. Maybe route the coax cable through the left side so you dont have to bend as much. It looks like a great setup. Can't wait to see what you do with the servers

[@DigitalSpaceport]

3d printer hints are dropping like flys to the wife, really need one for all the gear I have.

[@paulherman5198]

@@DigitalSpaceport Got a bunch of things you can make for the wife too

[@bc5891]

For coax terminations you should check the stinger after you strip the boot. Sometimes the metal strands will loop around the stinger causing interference also for the fiber you should look into SM not MM as SM will do up to 100Gbps basically future proofing your network needs

[@DigitalSpaceport]

I now have a 100gbit switch and a lot of am to run! Living proof you are right 😆

[@oleksandroleksandrovuch6545]

you are a cool man, nothing is clear but very interesting)) hello from Ukraine

[@HomeSysAdmin]

Finally had time to watch haha, very nice setup!! I might have mounted the fiber switch rotated 180 so the connections come out the bottom though. I actually prefer zipties over velcro where they can be used, especially stiff RG6 runs. The velcro just doesn't hold tight enough. How is the antenna signal with the 1-to-8 splitter? I have a 1-to-4 but purposely bought one with an amp (Channel Master) as I was concerned about signal loss.

[@DigitalSpaceport]

I have a booster (same brand) on the antenna and the signal at all the drops is very good. I am not far from the towers and do have decent LoS so that helps for sure. Antenna is a cut piece of coax stripped and made into a 16" diameter loop.

[@1sysop198]

I love doing work like that... Looks good....

[@DigitalSpaceport]

I wish I would have planned it out a bit better. I already want to get an RPi in there and an HDMI extender but thanks I tried to get it to look good.

[@PilotSteak]

5:24 - The Only mistake you're doing is NOT using a zip tie cutter.

[@DigitalSpaceport]

I'm going back to trim those edges

[@MrBriansaunders]

It hurts my soul each time I see any kind of wireless technology being put into a closed panel.

[@aarcaneorg]

I'm watching you zip tie that bundle of coax leading to the Leviton Splitter and can't help but keep thinking "This is why cable lacing was invented. Why isn't he lacing that cable instead of zip tying?

[@DigitalSpaceport]

Because I just heard about cable lacing right now 😜 also looked it up and I would need some additional skills never practiced before

[@denniswoycheshen]

Velcro

[@Jannickjay]

@@denniswoycheshen yes Velcro is best!

[@kevinpriester7478]

It's your equipment. Do what you want.

[@RobertoMFS]

Hi, great installation!, I looking to do some similar config in my house... what device do you use at the other side of the Mikrotik CRS305-1G-4S+IN MM Fiber networking switch? Thanks in advance

[@DigitalSpaceport]

2 videos on that in the works. On 1 side is my 3 racks of gear and they include for the network stack a Mellanox SX6036/ Brocade ICX 6610 and Dell 5548p for the rack needs. On the residential side I have another Mikrotek CSS326-24G-2S+ that does the house drops internally + the pfSense router and 5 wireless APs. Network Diagram in next networking video.

[@pagpablo]

Do you have more info about the over the air antenna over coax that you show at the end of the video?

[@BradleyC]

I'd like to know more about the ar150 and your use for it.

[@BLBlackDragon]

Zip ties... Not a mistake, but very "old school." I stopped installing zip ties back over a decade ago. Velcro straps are a better option, as they can be quickly undone and redone several times, without having to throw away and get new. About the only thing I would have done different, is to get a power strip whose plug oriented correctly, so you didn't need a whole lot of extra cable from the extenders. I do have to say, you have a very organized setup. I'm somewhat envious. I have a fairly crowded Leviton 32"

[@DigitalSpaceport]

I have more gear I am thinking of adding and indeed the power strip was a bunch of compromises. Leviton makes a nice one, its of course stupid expensive.

[@sirc625]

You already knew there would be comments about using zip ties over Velcro ties lol 😂 I would have used Velcro ties just for ease of adjustment later. Also, I would have used double sided Velcro tape to mount the Smart Things hub. Other than that, great job 😁

[@DigitalSpaceport]

Yeah someone else pointed out the super strong double sided Velcro and I have some ordered now. Looks like a great use for it plus I have more things to mount.

[@tristanpunzalan5928]

I'd like to know what screws you're using.

[@AceBoy2099]

Question, why have the 10g in there? There's no devices connected through that cabinet that needs 10g is there? Could just keep the 10g in the rack, or do you not have structured cable to the rack (aside from that specific fiber)?

[@BigWill3855]

I’m just upset you didn’t use flush trim cutters on the zip ties.

[@DigitalSpaceport]

But what if I went back after I read this and did? 😜

[@vboutique2188]

What's the advantage of the patch panel over say the following: Running 4 runs from a poe router to poe powered mini switches where tv's and computers are hooked up?

[@paultech9385]

Drop the zip ties, embrace the Velcro.

[@DigitalSpaceport]

Can it handle cleanly bundling the stiff stuff however? Agree Velcro is the best for non coax.

[@inmerfy]

good job, bro. why you not use 19 rack mount case for your cable?

[@DigitalSpaceport]

I have 3 racks and a bunch of network gear on those and an internal network switch also. This is kinda the demark between those zones. I have made a network map now and will have that in the next networking video on my cleanup of the server racks networking. Thanks!

[@technerd9655]

That was my question. I NEVER use these structured media panels. I'd rip it out and replace with a 19" Rack without a 2nd thought.

[@greglopez8206]

Velcro! Velcro! Velcro!

[@technerd9655]

What is that AR 150 device?

[@jasonjahnkeinla]

1st Comment 😍 Chia to the moon 🌙

[@Gildermesh]

I had to laugh you kept forgetting your cable stripper cut at the back and not the front, glad I,m not the only one😊

[@DigitalSpaceport]

At least I didnt cut myself during this one.

[@JasonsLabVideos]

Clean, I personally use small rack mount enclosures ! Dislike these network pannels!

[@DigitalSpaceport]

These are a pain to deal with. Had I known how things would evolve in the house and garage, I would not have started with one of these. It does have the conduit routed from the attic, and the attic is not a fun place in this house, so I just had to come to terms with it and clean it up.

[@JasonsLabVideos]

@@DigitalSpaceport YUP! you did good. Clean and simple !

[@michaelacre5114]

I wonder how well the wireless is going to work in this metal enclosure. Looks metal anyway.

[@DigitalSpaceport]

It is not great TBH but its wired backhaul to the 4 other mesh AP pucks so overall house coverage is still excellent. The speed isnt amazing as its 866 max on these. Leviton does make a wireless friendly (I guess plastic?) version of this but it is substantially more.

[@technerd9655]

Not well, never put a wireless AP or wireless router in one of these!!

[@Mack_Dingo]

You are crazy not flush cutting those zip-ties

[@DigitalSpaceport]

I've been known to live on the edge

[@jonlewis5061]

I do satellite tv. I can understand having some slack in the lines in case work has to be done later, but why leave that much of the orange fiber cable? Just seems like over kill.

[@mattmancl3370]

What kind of antenna do you have?

[@SloGhost]

out the ziptie together in the other way so they can be taken apart without cutting if needed

[@DigitalSpaceport]

I'm workin on it lol. I've come full "hook and loop " haha

[@TheSouthernMale]

I found another source to get used 20TiB SATA drives, but would rather support you, any idea on when you will get your next shipment?

[@DigitalSpaceport]

I've got a call in right now to see when they are getting in. Asia Pacific moves fast sometimes and slow at others. Week or so. You feeling the pressure now that I catapulted into the lead ?

[@TheSouthernMale]

@@DigitalSpaceport Keep looking in that rear view mirror my friend, I will, some day put you back in mine. If you notice, I am already getting close to you, just 6 others suppurate us and I already have enough to move up a few more slots. I will hold off from getting them for the other source, I will commit to at least 8 20TiB SATA drives, maybe more, just depends how things go financially.

[@taieric8978]

The cable frame and the fiber switch should swap bits

[@DigitalSpaceport]

Ya know what you have a good point there. I am 3d printing a new fiber frame sometime and will reorg it.

[@espowari]

I used 3M Duo Lock to mount things. Very strong and you won't see it.

[@DigitalSpaceport]

Just ordered some. Thanks!

[@DonDelyriaIII]

Zip ties are fine, Velcro could be cool though..

[@William-D-]

this man likes his zip ties lol

[@Weirlive]

I missed it, why did you do Power over Coax?

[@DigitalSpaceport]

That is for powering the Antenna amp that is in the attic. Makes the signal work great!

[@Weirlive]

@@DigitalSpaceport perfect! thanks

[@oaklejant]

Is it ok for the UPS to be placed inside such a small wall box?

[@DigitalSpaceport]

Now that's a good question. I'm going to look more into this

[@ryderholland]

Per code, its not rated to be in a wall at all, the “correct” way to do this would be to have the 120v all externally mounted, or have the ups on the floor or a shelf and have to ups outlet go into an in wall rated 120v inlet that is connected to romex and then terminated at an outlet inside the inclosure. That being said as long as the ups has airflow and doesn’t overheat this setup will likely be fine.

[@technerd9655]

@Ryder Holland a better way would be to use a 19" Rack and out the UPS on a shelf, or get a rack mounted UPS.

[@discrtidunkwn]

So careful with fiber bends until the last bend into the switch...then just close enough. At least at the end of video you gave more slack.

[@DigitalSpaceport]

I gotta say I am not really happy with the coil and tension especially at the heads. Trying to find a nice way to "un-F" it when I get a 3d printer for sure.

[@discrtidunkwn]

@@DigitalSpaceport yeah, custom pieces to fit your needs at the touch of a button and a bit of time is nice. So many great printers out there now. It's a fun rabbit hole.

[@MrJJ65]

Wireless back-up in a metal case???

[@DigitalSpaceport]

One of many mistakes I have made. Need an update video on the network, its evolved so much since this video.

[@BryanSeitz]

Looks like OM1 fiber which isn’t for 10G?

[@DigitalSpaceport]

OM2 50/125 which is also orange and does negotiate at 10g and speeds at 9gbit solid over the distances it's run for me. It may be getting used as the pull string for OS2 however given new switch is much faster.

[@likeglue42]

It's nice but that spool of fiber feels like wasted space in the network panel. Clean for what it's worth tho.

[@DigitalSpaceport]

Yeah this is really more of a demark for the houses internal network and the racks and workbench drops and it is indeed wasteful (and a tad hackie) but it was like OM2 vomit in there prior. Thanks!

[@MatthewSmith-se2rb]

Get some side cutters for trimming those zip ties flush. Trust me your arms will thank you later

[@DigitalSpaceport]

Im looking now and like what Im seeing!

[@BlueNoteStan]

I'm not upset at the fact that you used zip-ties, more so the fact that you tried to break them off with the tip of the strippers and when that didn't work, you used the cutting part of the tool. The first time you did it, I was like, yeah, that don't work homie, but then you kept doing it and I'm like, c'mon man, surely you learned the first two times... but nope... kept on doing it. Otherwise, great video!

[@DigitalSpaceport]

Did I go back and fix this? Yes. Did I clip myself with an edge off one of the zip ties, yes.

[@ICgasm]

Buy a pair of side cutters, using a wire crimper is a poor choice.

[@DigitalSpaceport]

yeah I am looking at some sets now

[@balla2172]

Eek I have to much more powerful gear need an actual wall mount rack

[@includenull]

How quintessentially American

[@DigitalSpaceport]

do they not use these in other parts of the world?

[@includenull]

@@DigitalSpaceport In the UK at least I've never seen one of these in-wall media boxes, not even in new builds. Most of our houses here are built of brick. I've only ever seen these in videos from people in the US and sometimes Canada.

[@DigitalSpaceport]

You are lucky these things are not great to add stuff into after the fact and you always need to add stuff in later.

[@includenull]

@@DigitalSpaceport More often than not in the UK I see people install a small wall mounted network cabinet high up in a closet, or under their stairs. That seems to be the go-to for people who need more networking equipment in their houses.

[@technerd9655]

Whyyyy? I am absolutely against the use of these structured media panels. A STANDARD 19" Rack, while not as space efficient and not as aestetically pleasing, is far superior for many reasons. Even for home use! 1) standard 2) easier to work with, easier to troubleshoot 3) more options available, no vendor lock-in 4) more hardware options, rack mounted router, rack mounted switches, etc. 5) more expandability 6) Ethernet, fibre, and Coax patch panels (though I guess you could just mount a Coax splitter to a blank panel by drilling a few holes or 3D printing one. Etc. Etc. Yes, these look nicer, but just are not properly functional. That SmartThingsIoT hub ideally should be placed much closer to your Z[ed]-wave/Zigbee devices for more reliable wireless signal, at least you knew enough to connect it to Ethernet and not WiFi! (I wish more smart devices like smart switches (anything that are stationary really) would use PoE, MoCA, or Powerline networking instead of wireless (wired is ALWAY superior to wireless whenever mobility is not needed and practical).

[@justinhannah1023]

wrong type of fiber for 10G. need to use aqua or velvet colored OM3 or OM4 fiber. youre using OM2 multimode which is not qualified for 10G+. its like trying to run gigabit on cat3 phone wire. 😒

[@DigitalSpaceport]

OM2 does work (*and used to be rated as such) for MM 10Gbit over the distances sub-80 meters. I am using a 30 meter max length. I did not purchase it new for this use, but rather got it free with a server room cleanout. I would of course purchase OM3+ for any modern runs but I also believe in being cheap and not wasting money. In addition it does work without issue at 10Gbit without error.

[@justinhannah1023]

@@DigitalSpaceport are you using 850nm or 1350nm optics?

[@justinhannah1023]

@Digital Spaceport oh yeah you could probably use a white string for 30 meters. 😆

[@DigitalSpaceport]

@@justinhannah1023 850

[@LetsPlayWithLinux]

What is this? Talking about not to bend the fibre connection but doing exactly this! Also why do you put an 4G Backup router in this metal cabinet? This is really american work... Looks nice, works like dump.

[@DigitalSpaceport]

Im getting a 3d printer to print a better loop and the signal to the 4G backup is great. I am not far from a tower and it feeds via cat6 to the router and then to the 5 AP wireless mesh for the house. Funny you just lump everyone in like that, very much stereotyping. I hope you have a good day all the same.

[@LetsPlayWithLinux]

@@DigitalSpaceport I didn't wanna sound rude, it's just an american thing to do things nice looking but not technically perfect ;)

[@TheSouthernMale]

Well crap, was about to purchase 8 more 20TiB SATA drives from you but you are out of stock 😭 I am starting to wonder if this is a plot by you against me so I will not catch you.

[@DigitalSpaceport]

They will be in Friday or Monday and prices down a tad and JBOD 3 gets repurposed in ~3.5 hrs muhahahaha.

[@TheSouthernMale]

@@DigitalSpaceport Well you do not think I will let you get away with that now do you? LOL, I just checked, since joining the same pool you are on I have contributed (Found) 3 blocks, to you 2 blocks, so there is that Haaa back at ya.

[@TheSouthernMale]

@@DigitalSpaceport I will check your site on Friday, credit card sitting here waiting.

[@TheSouthernMale]

Make that 4 to your 2. :)

[@DigitalSpaceport]

I "should" be around 6-7 by now

[@akletke1]

Flush cutters man... C'mon...

[@DigitalSpaceport]

I did go back and trim this up with some nippers (based on the overwhelming feedback to do so) and tips are not protruding any longer.

[@aleksandr296]

10Gbit fiber for home ?? WTF !??

[@BigWill3855]

Getting pretty common now.

[@scotmaciver]

lol that's what I came to ask. 1 gig is overkill for 99.9999% of folks, much less 10.

[@gromit_2959]

@@scotmaciver Does this meen I have to tear down my 40Gpbs setup?

[@WillOnSomething]

It's becoming more common, even if residential subscribers aren't currently getting full 10Gbit's provisioned on their plan. It's more of future proofing when you want/need higher speeds later. Comcast has been using 10gig fiber equipment for it's "gigabit pro" service (fiber based service thats different from their trad cable offerings) for a while now, and residential customers only had 2 gigs of the circuit, and apparently now they've started upgrading customers over to 4Gbit tiers

[@DigitalSpaceport]

I wonder how you will feel when the 40Gbit video is out... JK lol? But seriously I have been running 10Gbit for 6 or so years and love it connected to my unraid server with a super fast NVME storage array for files I access often.

[@UKsystems]

I hope that panel isn’t metal because if you’re putting anything that that uses wireless communications inside, you have absolutely absolutely no clue what you’re doing

[@icebread9335]

This is some really cool content, but I must be honest... wtf is up with this chia bullshit... it doesn't get any clicks, only this kind of video here

[@teenhon]

wtf u need all this crap for tho

[@greenis3006]

All this and you don't have a 3d printer to make cable guides for that coax?

[@DigitalSpaceport]

I just looked this up and am looking for a decent 3d printer. I need it for so many things and hoped to get one for Christmas but didn't.

[@Wffgcdewffkdhrhdb]

Nothing wrong using cable ties. But the colour of the cable tie make me frustrated 😣 w t F colour is that ???? 😣😣