HOMEMADE 588cc 3 CYLINDER GX FINALLY GETS ITS TURBO!!//Part 2

[@matthewf1979]

It should make some boost with a moderate load. Crazy contraption you slapped together! Nice work on the manifolds too. That stuff takes forever.

[@tomplumb1]

Man!!! pls do not leave it so long between videos! The fabrication content is awesome and seeing you problems solve and design custom parts is what makes this channel. please keep it up!

[@councilhousecreations8035]

Thanks man this year I'm getting on it!!

[@timurmurzabekov3821]

How hp?

[@tucker934]

@tomplumb1 be a bit easy on him. this kind work takes quite a bit of brainstorming, patience there’s a whole list I could name. Just in the engineering aspect that’s including his time editing the video which can take a lot of time! Be patient my friend if the creator were to rush he could run into all sorts of issues and end the whole project because of one very tiny mistake!

[@Potato37184]

​@@timurmurzabekov3821 20hp

[@reddenley9822]

I watched you build this engine, sir, and I have to tell you that you are an amazing fabricator. The stainless cool side and all the pipe work is just awesome. I love your work. Great channel.

[@councilhousecreations8035]

Wow, thanks!

[@Dontfearthereaper001]

Awesome for the draw-through set up. We need to see more of it. It's so simple and cheap.

[@councilhousecreations8035]

Thanks man not sure how it will hold up might switch to a blow thru but we'll see how it goes first

[@ivorscruton5121]

​@@councilhousecreations8035Blow through would require the carburettor to be pressurised, additionally the fuel pressure would need to be increased above atmospheric, in direct proportion to the boost. Not overly complicated with the use of a fuel pressure regulator with a boost nipple added to the atmospheric side of the diaphragm to fool it into thinking that's what the atmospheric pressure is. The carburettor needs to be sealed, which is the tricky part, with overflow and other venting, such as through the slide. My project was turbo charging an old Austin Mini. First I attempted fuel injection using a Volkswagen CIS, minus one injector, it would either idle with poor high end, or have high end without idle. Frustrated, I eventually found a Daihatsu Chrade turbo carburettor which was a blow through system, this solved all problems. Good luck, I hope this tidbit of information may help avoid some potential pitfalls.

[@gabrielwalker421]

yep draw through is the way to go for carb turbo

[@oceanpathway]

Sounds like a diesel engine in a semi truck Glad you are back after a long time ❤

[@councilhousecreations8035]

Thanks man I hope it performs

[@RallyRanchMotorsport]

It's refreshing to see some proper fabrication with something like this. My favourite thing is that awesome 3 into 1 exhaust collector you created. It actually makes the engine/s sound great 😁

[@KianaRYN]

T

[@tonystanton9223]

i totally love that you engineer like i do, you havent fallen into the new age cnc everything, theres something special about hand crafting everything, measurements are not important, that looks about right is so much better ,totally love this man, keep it up

[@councilhousecreations8035]

Thanks man if it looks gd it is gd!

[@tonystanton9223]

@@councilhousecreations8035 exactly

[@HeartLessGem_]

The master returns! Been checkin youtube every now and then to see if you've uploaded, excited to see where this build goes 👍🏽 love a little turbo noise 🤙🏾🇦🇺

[@councilhousecreations8035]

Thanks man I won't lie it's basically a noise machine lol 😆

[@HeartLessGem_]

@@councilhousecreations8035 well you are a machinist 🤷🏽‍♂️ you'd probably be able to make an adapter plate to mate a motor bike gearbox upto it, could make a cart 😁 weither its off road or on the street! Makin a gearbox adapter is a little hard but considering you've slapped 3 motors together and put a little turbo on it, I'd say you can do anything 👌🏾🤙🏾

[@forced4ph]

I love that you’re using so much stick welding. It adds more vibe to this already mad project. 😂

[@lucid523]

Honestly seeing 3, 1 cylinder engines is pretty cool and the fact it sounds like a 3 cylinder is so cool, I'd love to see like more options like 4 cylinders maybe if you could a 5 cylinder with all of them and etc etc love to see all types of number of cylinders with 1 cylinder engines ngl its a great experiment love this fr

[@theusedbox]

Amazing build sir the time you take to make it right is very refreshing, subscribed.

[@councilhousecreations8035]

Hey man thanks a bunch!

[@MrGiXxEr]

Technically, with the addition of the turbo it makes it a racing motor. So in essence, it's a GSXR600 now.

[@councilhousecreations8035]

Exactly!!

[@oryxr5354]

I wouldn't agree with you on it being a GSXR600, I'd rather say it's a Triumph Daytona 600, with it being a 3 cylinder

[@GrichaBarbarin]

КПД трёх моторов будет меньше

[@ХОББИ_Олега]

​@@GrichaBarbarin Нет, КПД наоборот лучше, так как гораздо легче крутить три маленьких поршня, работающие по очереди, чем один огромный, вращающийся "впустую" большую часть своей работы. Но тут дело не в этом. Дело в том, что крайний двигатель, через который проходит мощность всех трёх моторов, просто не выдержит. То есть от этой компоновки толку нет...

[@GrichaBarbarin]

@@ХОББИ_Олега имел в виду по сравнению с одним трехцилиндровым двигателем.

[@S1lentRunning]

Astonishing work on those manifolds, I take my hat off to you sir

[@councilhousecreations8035]

Thank you very much!

[@bobaverage]

Fair play doing it all with the stick welder.

[@TheMrDarius]

One thing is for certain is that how thick that exhaust tubing is, you never have to worry about it getting any rust holes anytime soon like conventional car exhaust tubing. Pretty stout! I’m impressed.

[@martyn5799]

We need to crowd fund this lad get him some tools like a drill press etc etc if anyone who knows how to ser it up please get on it asap.What he puts together with the tools he already owns is absolutely amazing 💯💯🔥🔥

[@bikingnutcase0]

I've gotta commend you on your patience welding all those pie-cuts with a stick welder, very very nice! I found the "Splink!" of the slag popping off at 16:17 particularly satisfying!

[@daphantomstranger]

When this popped up in my feed I clicked right away! Didn't even question it.

[@Jesse_Drinkmilk]

Finally. A small KZbinr who can weld

[@SoutheastCaliforniaSirens2006]

For weeks now, I literally had plans to build a DIY subcompact car from scratch using parts and a chassis salvaged from a second gen Honda Pilot. This would have also used a few parts from the third gen Odyssey such as the gauge cluster and petals but a steering wheel from a Freightliner M2 112. However, the engine for it is actually an interesting choice. i coincidentally settled on a similar idea to this, except its a bespoke 672cc monobloc turbo based on the Predator 224 with a turbo from a GM L3B or VW TDI. This would be mated to something like an Aisin F21-250 but idk at the moment bc its still in the planning phase.

[@Codrin.70]

Man you are a genius! This is called a profession! Congratulations !!!

[@shyamricky597]

This channel is becoming a holy grail of over engineering brilliance.keep it up mate 👍 From India

[@PALM311]

Planning on building a three cylinder out of three horizontal Briggs and Stratton engines and this build will help me out! Sounds and runs absolutely awesome ! “Triple Threat”!

[@boccatxrx5023]

The joys of the arc welder! So wholesome mate! Ive made jusr about everything using a $99 stick welder for 22 years! Just bought my first MIG/TIG the other day, its nice but the ark does the job too!!

[@BIGSMOKE-bl2lq]

Always used stick got a mig now just use it for quick easy jobs but if it needs some strength bust out the stick and if its gotta look pretty i take it to work and tig

[@councilhousecreations8035]

I use a Lincoln 3 phase mig at work all day but I've only got a little single phase mig at home so it just feels better doin most things here with the stick. Its amazing how many comments I get because of the stick welder

[@The3chordwonder]

Those collectors are gorgeous. Nice fabrication job!

[@mostlymotorized]

😂nice. Good clean fun. Get a temp gun on each exhaust port at the head. More than likely doesnt get the same A/F ratio to each cyl with a draw thru setup. Fuel tends to puddle in the tube bends, maybe that can be tuned somehow

[@councilhousecreations8035]

Thanks man u might be right. Might switch to a blow thru setup in the future

[@rdallas81]

Blow through is the way to go. ​@@councilhousecreations8035

[@theoverlanderutv2747]

The machining and fabrication is ultimately impressive. Bit the fact that it sounds immaculate is really something to be admired. I have a little 800cc inline 3 in my kawasaki sxs, and though the exhaust sound is similar, it is so heavily muffled and detuned, it just doesn't have that attractive exhaust note this has. The turbo just adds to it

[@councilhousecreations8035]

Thank you very much!

[@nop3noperson]

Dangit..every youtube channel is doing this. You show the results at the beginning of the video. Awesome build mate. Awesome.

[@oryxr5354]

So happy to see you made another video, hope there are many more in 2024!

[@councilhousecreations8035]

I hope so!

[@slimshady6718]

Well !!! I don’t know how I come across this channel ? ……..but I’m glad I did ! New sub 👍👍👍awesome skills !

[@damnthiccassboye7138]

love it , imagine putting stage 3 kits on all those predators can put out some serious power

[@sophakpeth4346]

I’m happy to see your back! Thank you for uploading again.

[@councilhousecreations8035]

My pleasure!

[@christopherizon1167]

I really appreciate the extensive use of the angle grinder

[@hermanbotha1449]

Been waiting for this video for so long!! Thanks for documenting it. I love your work and obviously so do you!! Cant wait for the next one. Keep it up!!!

[@TheShamanizer]

Fuckin' 'ell, feel like I been waiting forever for this video upload. Sounds like my old speed triple. Beast mode engaged!

[@councilhousecreations8035]

thanks man

[@BuildBreakFix]

Omg bro is stick welding this! Damn liked and subscribe that is amazing all in itself!

[@isaacbrown511]

Lol you watched this too

[@karlalton3170]

Good to see you back Gezzer , great job 😁😁🤘🤘

[@councilhousecreations8035]

Hey, thanks!

[@nonarrativeboxingnunn9856]

My Man!Been Waitin' On This One!!!!💪🏿💪🏿💪🏿💪🏿💪🏿

[@JayHaell]

The fact you welded the manifold with stick is awesome, I couldn't do it properly even with TIG, probably... Glad to see you back 💪

[@councilhousecreations8035]

Thanks man stick all the way 💪

[@MosinMaster]

The welds on your manifold are pretty darn nice for a home welding setup! If you can find/afford it look for some MG Super 600 rod. It is crazy expensive, but it's basically cheater rod. As long as the metal is clean it will basically run itself. I use it at work for air brake pipes on railroad cars, and it would be perfect for this application.

[@manoo422]

The main question is what are you going to do with it? As you said once under load it might start producing some positive boost.

[@S-North]

That's some quality fabrication. Great to see you're back!

[@councilhousecreations8035]

Hey, thanks!

[@BenRelle]

Awesome! Turbo needs an oil feed, though, right? Is the black one with the fuel tank on doing anything? HT lead looks sketchy and didn't seem to sound too much different when you turned it off. Need something to put it in now!

[@deborahchesser7375]

There’s another guy that took everything apart as a kid. I took the motor off Dads tiller, it worked great on my go kart until I had a sudden pain in my ass. It was my Dads foot ! He said boy how long did it take you to get that motor off my tiller ? I said about thir thir thirty minutes 😆 he said I’ll give you 25 to get it back on there ! And so begins my career as an electro-mechanical technician. We couldn’t help it, if 2 batteries made your toy run ok, then surely 4 made it run even better? Tinkering is the best therapy, now days I spend it on vintage motorcycles, my true love. 🐾✌️🇺🇸

[@dav1dsm1th]

Good to see a new post from you. Thanks for the videos.

[@councilhousecreations8035]

Thanks man

[@haydenc2742]

Now get a small tank of oil, get one of those super cheap 12vdc clacker fuel pumps, plumb in the turbo so it has oil for the bearings, and do a full run in test on that little beast! (I think redbeard did that for a small diesel engine he put a turbo on) Might go as far as finding a cheapo muffler too...just to tame it down....if you want So awesome...keep em coming!!!!

[@TheAyrCaveShop]

Just came across your channel, that's some crazy mad scientist stuff...love it 👍👍

[@BoostedMike2]

mans got a lathe............but not a measuring device, finally a creator who's work is less accurate than mine

[@jayflow7949]

Bro Your Arc Welding is on Point!!! Positional Arc Welding Pipe is The Hardest Kinda Welding!!!!

[@CharredSteak]

This sounds fantastic for what it's worth, the turbo just sounds so right

[@carlzrx]

Outstanding work and it’s good to see you back

[@timbyford21083]

This is like bigger than the 4th dimension kid!!!! ❤

[@daylightdies7194]

I hope you are well and life has treated yourself and family well it’s nice to see you back

[@councilhousecreations8035]

Thanks man feels gd to get a video out hopefully this this will be gd

[@notyouraveragegoldenpotato]

Thats some madlad farication with a very basic tooling set up! Nicely done

[@northwoodsrippers9639]

What’s the background music at 19:52 ? Please and thank you!

[@councilhousecreations8035]

It's called autumn haze by West and zander 👍

[@tikiman48]

Incredible. Funny i was thinking about doing something like this all week and then i see this video. Sounds great too, would love to see this on a go cart or something

[@brycemueller7330]

is each motor timed 120 degrees apart so they're not all on the same stroke at the same time, also i've seen people use build an "expansion chamber" type of thing in the intake for boost on small engines

[@brycemueller7330]

Its called a boost bottle I believe

[@caseybinion806]

Very cool I’m glad to see the upgrade But I see something the engine with gas tank it doesn’t have a spark wire on the spark plug ?

[@michaelrobbins9983]

I personally didn't notice this until you said something. Hope he sees these comments and fixes it and let us see the video of it running after the fix lol.

[@councilhousecreations8035]

Lol yeah couldn't fit plug cap on because of the inlet manifold so I put a blue connector with a ring end on it then just screwed it on top of the spark plug. It's a bit crap I know..

[@caseybinion806]

Nice that work sounds good

[@2fxst2drxft]

Wow I never thought they would have sounded like that put together in the same exhaust pipe..

[@inamalabrory8413]

I cannot wait to See it on wheels... Good job..

[@councilhousecreations8035]

Thanks man me too!

[@dogsandwich-b2r]

Glad I waited a year for a comeback💪

[@councilhousecreations8035]

thanks man im not glad i waited a year!

[@emmettwalker8268]

That would be nuts in a bike build

[@life_of_riley88]

Wow, all that hot side work done with a STICK welder is impressive. Seriously, I do a lot of tig welded stainless exhaust work, and there's no way I could do that with a stick welder. I'd be burning holes and cussing like a sailor.

[@councilhousecreations8035]

Thanks mate! I did burn a lot of holes in the stainless pipe but I have the power of editing to smooth it all out 😎👌

[@Adventure_Van_Upgrades]

🎉 🥳 i did wonder what youd been up to all these months with the new workshop space! Looks & sounds great in the introduction , im just about to watch now. Pleased to see you make a return for 2024!

[@councilhousecreations8035]

hey man, yeah hopefully this year will go a lot better, hope your well.

[@Adventure_Van_Upgrades]

@@councilhousecreations8035 I struggle to get all my projects done before starting another that's the biggest issue! Sometimes life is too hectic to make time for filming & family comes first. I hope this year's going to be easier for you.🤞 looks like your channel has exploded over the past few years so there's definitely potential with some regular uploads ( just difficult to achieve when doing these types of projects/experiments). Amazing work on the exhaust/ turbo system pipework it looks brilliant & all done with your trusty stick ✅ Its going to be Very interesting when you get this beast bolted into a machine, looking forward to the eventual test ride videos 😂

[@councilhousecreations8035]

Man u sound just like me I must have started dozens of project in the last year but only a few worked out and I didn't even record them 😅 I even put a man lorry engine in my l200 just didn't have time to film it...

[@PatonMachines]

​@@Adventure_Van_Upgrades Same here! Tend to start more projects before finishing what's on the table!

[@Tmanstomp100]

This thing legit sounds awesome like a truck engine or something

[@loomifidih]

so glad to see you back

[@firstielasty1162]

Wow. You're good with stick welding. I do tig mostly, and would probably not try that if I had only stick. I'm impressed. The "collector" (divider? diffuser?) After the compressor discharge looked difficult and turned out pretty nice.

[@councilhousecreations8035]

Hey thanks yes it was a pain welding 1.5mm tube with 3.2mm rods 😅👍

[@Tommysmess]

I've been waking for this 😎😎😎

[@BlockGod_1832]

you can see at 20:57 that cyl #1 doesn't have the spark plug cable connected or am i missing something?

[@halfnelson6115]

Lol. I've never seen someone take a grinder to a running lathe. 😂 Anyway, your engine is pretty sweet. Good for you.

[@ronbradshaw7404]

You really should make it a blow-thru. Those Mikuni VM carbs are easy to adapt, just make a nice, big enough plenum and connect the 3 carburetor fuel overflows on the plenum, pressurising the fuel bowl. You could make it one or 3 carbs!. You will need a pressurised fuel system tho... Greater challenge, greater reward!.

[@limysyenpai537]

welcome back

[@DonnDIY]

Well done! Sounds super 👌🤙

[@councilhousecreations8035]

Hey man Thanks a lot! 🙏

[@Wasketa]

It sounds awesome, like an old diesel truck ❤

[@TorchFpv]

Very cool! Now wire the kill switches together 👍🏼

[@partyalldaypartyallnight1057]

That sounds fantastic! Now i have to build one.

[@64BitMatt]

Brave welding that with Stick. i know i couldn't do it, That thing sounds amazing btw!

[@trxtech3010]

I always wanted to do something like this. Super cool!

[@JamesMwaura-e1j]

I like your fabrication skills broh.

[@bradensmith888]

Could you premix the gas with 2 stroke oil to help prolong the life of the seals in the turbo? I know they don't like sucking straight gas

[@lazarusmunien2087]

Nice workmanship bro,should have boosted it through all three carburetors, think it's crying for more fuel with that extra boost ❤

[@vincehoffman179]

wow sir your manifacturing skills are so good!!

[@metalrott324]

you should reinforce the top and sides of the crankcase with 1/2 inch aluminum plate. I do but I don't want to see it blowup

[@glumpy10]

Sounds amazing!!

[@FarmerFpv]

What in tarnation did you build, son? That is one crazy contraption. Fixin' to fly to the moon? Bout to eat some toad frog and hush puppies while I watch this insanity. Wish I could go out and play with the toys. It's so cold my weenie was an innie all week. It looks like a helmet sitting on shrubbery.

[@F6garage]

My old engine!!! I love it mate

[@fetus2280]

sounds amazing for what it is... I am impressed mate. Good on ya. Cheers.

[@councilhousecreations8035]

It might explode but it'll sound good while it's doing it!!

[@fetus2280]

would make a great vid though ... as long as nobody dies in the process lol @@councilhousecreations8035

[@Spikeinca23.]

Genius. More please...

[@GuildOfCalamity]

LOL, a year goes by and then all of the sudden he hits us with the uber-build... noice

[@greghackney8437]

So independent timing, no firing order? Sound great.

[@nathenleffert_official]

Anyone noticed the 3rd cylinder doesn't have a spark plug boot attached to the spark plug and btw you'll get better throttle response if the carb is before the turbo

[@itstimetoblog5031]

wow, it's beautiful and you're so good at doing that. I wish I had a machine like that, put it on a boat

[@MAD450r2]

Great job so far. Keep up the great woek.

[@3scw]

Got a couple questions one how many bar of pressure does that turbo spool ? Have you strengthened the rods crank and cylinder , cause in my experience its a 7,8k rpm engine , with tuned variation low in the 10k , i know it probably in the aid of science so reliability isnt realy a thing , but these are carbed engines and pick up and gearing is more to do with sproket and chain length by the video it looks like instant delivery , but does it run constantly under the turbo , and my other question is on the lathe it intrest me on how do you know its skimed true cause the needle chisel moves inwards on the resolution of the spindle so how do you know the resolution has skimed 3mm across a 360 degree surface for example

[@keldervasconcelos9926]

Melhor ideia veio agora com isso que vc fez, eu tô querendo fabricar uma jetboat e motor assim fica top 👏👏👏👏👏

[@TylerB175]

Sounds awesome, almost like the the can am maverick turbo engine

[@rexhorning7228]

I really like it!!! Like to see it on a mini bike or go cart

[@peraz968]

Hi. When using lathe and high speed steel tools, you must know what is the maximum rpm. If you get over it, you will burn your tools. For steel diameter around 50mm, maximum speed is abaut 360rpm. Maybe litlle bit over that, but not very much. Forget harry, when doing things with hss. If you want speed, go and get carbide tools. With carbide tools, you can safely approxymetly X3-4 the speed of rpm versus hss. Just you to know the difference of hss and carbide inserts etc.

[@wazittuyoo2147]

Where is it going? Can hardly wait to see the end use.

[@xenomorph1317]

This bearded man is a genius…..