i also build my own compressed earth block machine in india.. looking for best cheap method for conveyor belt.. you saved my days.. thanks man..
@rodalo16364 жыл бұрын
Tnaks tou you for watching
@taseluio8 жыл бұрын
cutting the metal without shirt, LIKE A MAN!!! great!!
@thehllcdotcom7 жыл бұрын
hahaha i just was saying the same ... dude is a bad ass
@mrtechnophile34836 жыл бұрын
Like a man with lots of small burns...
@rodalo16364 жыл бұрын
Hi I was a very hot day, inside was a oven, greetings
@rodalo16364 жыл бұрын
Hi friend, was an very hot day like an oven
@UriahRain5 ай бұрын
If you like that tune check out..Rainmaker One Less Reason
@rodalo16365 ай бұрын
Nice, thanks.
@seekgodfirst16058 жыл бұрын
Great job, I'm doing something similar on a much smaller scale. Thank you for the video
@rodalo16368 жыл бұрын
Thanks
@TheBoczk267 жыл бұрын
Where did you get the belt from? I am looking at making a similar project myself.
@rodalo16366 жыл бұрын
Bought in a rubber factory
@jacksonvilledrivemap40122 жыл бұрын
Wide Maya, have your contractor Use a simple conveyor and save the backs and knocks of the workers. Good luck.
@arbenibraimi65843 жыл бұрын
Great job sir. I just wanted to ask for the rollers arent they a litle bit thinner or what.. i have a conveyor but the rollers are thiker thanks
@rodalo16363 жыл бұрын
Hello Arben, they are made of PVC but their terminals have wood and in the center they have a metal tube that is crossed with an iron from side to side
@arbenibraimi65843 жыл бұрын
Thanks
@matisspinka56115 жыл бұрын
Hi, nice diy video, what kind of bearing do you use for small rollers (pvc pipe)?
@rodalo16364 жыл бұрын
Yes pvc pipe
@jamig.7254 Жыл бұрын
What was the overall cost of making it- per meter?
@lucaslivas58639 жыл бұрын
Very nice job!!!! 10!
@hlkihglkhglkhg6 жыл бұрын
Great video, Thanks. I would also like to know what belt material you used. Cheers
@rodalo16366 жыл бұрын
Hi, just a rubber 4mm, thanks
@guyokeng94714 жыл бұрын
Very illustrative video! Thank you! Just some clarities: 1. On both extremities of the U profile: one has a U cut but how the yellow roller can rest in. Screws are there but I can't understand how the roller is hold not to fall. And at the other extremity what happened to the cuts made.
@rodalo16364 жыл бұрын
Each bearing has 2 bolts below that are tightened to the structure, to tighten the belt, you release them and you adjust the endless screw until you achieve the proper tension and then tighten the lower bolts to secure it, greetings
@alexmattyspac76053 жыл бұрын
Welding with all that bare skin💪
@johndeleo30785 жыл бұрын
Great video, I have a question on the Blue rollers. Could you describe how these are constructed. I like the idea of using PVC to help keep the weight down for the conveyor I am building and would like to use your roller design.
@rodalo16364 жыл бұрын
Hi, pvc tubes and hardwood end tips crossed from side to side by a central metal tube inside the tube an iron that is affirmed on the sides of the structure, greetings.
@rodalo16362 жыл бұрын
Sure, +56 9 9824 3103
@job38four107 жыл бұрын
I got the impression that it's a warm day in the neighborhood. Nice build, what's the rollers made of and how are they held in place?
@rodalo16367 жыл бұрын
Pvc, plastic lids and center of metal tube crossed by a smooth 8mm iron and yes it was very warm
@hcmv94334 жыл бұрын
Hola. Una pregunta técnica espero me la puedas resolver: al no tener el sistema de rodillos en V (que al parecer son mejores para transportar agregados) tuviste algún problema con la cinta en cuanto o a si sube bien el material, si se sale la arena por los bordes, si no se desalinea la cinta constantemente, etc. Gracias y Saludos desde México.
@rodalo16364 жыл бұрын
No para nada, lo único es que al cargar en la tolva, si es arena o algo parecido, ten el recaudo de poner una goma atrás para evitar que caiga al suelo, saludos
@TheNightwalker2476 жыл бұрын
Thanks for the great video
@rodalo16366 жыл бұрын
Any time thanks to you
@JoshPLewis4 жыл бұрын
How many horse power is the motor, and what is its rpm? Is it three phase or single phase?
@rodalo16364 жыл бұрын
Just 1.
@GoldMiningGermany4 жыл бұрын
Awesome! I need this :D Keep on!
@rodalo16364 жыл бұрын
Thanks my friend
@mannyyabar76597 жыл бұрын
The naked welder yeah!
@rodalo16366 жыл бұрын
Yeah, thanks
@lucaslivas58639 жыл бұрын
Very nice job!!!! +10
@danwalters42248 жыл бұрын
That's awesome. I'm looking to do something similar. What did you use for the actual belt please?
@7731188 жыл бұрын
How do you contact Rodalo1636?
@rodalo16368 жыл бұрын
Thanks, just went to belt Factory and ask for 7mm thikness
@fernandomonteroespino95898 жыл бұрын
Nice work, you have a lot of creativity :)
@rodalo16368 жыл бұрын
Thanks, my friend
@rodalo16364 жыл бұрын
Thanks my friend
@robertorosasolivares38364 жыл бұрын
buenas tardes amigo, disculpa para que tipo de material es tu banda transportadora??????????
@rodalo16364 жыл бұрын
Hola Roberto, es goma caucho con un refuerzo interior de tela, saludos
@wannabejeeper8 жыл бұрын
What kind of reduction are you running to get it to that speed?
@rodalo16364 жыл бұрын
I experimented as I found the right speed with different pinion and chainwheels
@davidyoussef96264 жыл бұрын
This is how EL CHAPO escaped from prison :))) GREAT JOB CHEERS...
@rodalo16364 жыл бұрын
Thanks my friend
@zrun174 жыл бұрын
Keren.....
@rodalo16364 жыл бұрын
Thanks, my friend.
@bharatkumar66994 жыл бұрын
What is the cost of that rubber conveyor belt I am doing a project on it can u please tell me where I can get that rubber belt
@rodalo16364 жыл бұрын
For a 20 foot long conveyor belt you need rubber at least 4mm thick. In rubber it is worth approximately 6 dollars per foot. I bought this one from a rubber band factory. Regards.
@rananadeemtv18824 жыл бұрын
Nice
@rodalo16364 жыл бұрын
Thanks
@itsjustnotlikethat8 жыл бұрын
Pretty cool, so how much did this cost you when all's said and done?
@rodalo16368 жыл бұрын
Close to 500 Us
@jasone95 жыл бұрын
That's a bargain. Have you since built anymore?
@rodalo16364 жыл бұрын
No, I need only 2, thanks
@isabelcortes85405 жыл бұрын
what motor did you use ?
@rodalo16364 жыл бұрын
1 hp 1440 rpm
@stevenuluitoga20987 жыл бұрын
nice job
@rodalo16367 жыл бұрын
thanks
@dylano.s88004 жыл бұрын
What kind of U profiles have you used?
@rodalo16364 жыл бұрын
2mm 50mmX50mmX100 6m
@Iliketoweldandbraze4 жыл бұрын
You got to come up north and work you can actually put clothes on and then roll around on the hot Steel
@rodalo16364 жыл бұрын
Any time my friend, was to hot day.
@kjmcdow85037 жыл бұрын
I'm making a Diy conveyor belt on the floor well I called it the conveyor belts mini
@rodalo16366 жыл бұрын
Great
@BobVerwey4 жыл бұрын
when someone has so little self respect in terms of safety...its a shame really...its not manly..it really is'nt!
@rodalo16364 жыл бұрын
I'm sorry you think so, maybe you have a delicate skin.
@drelaw20022 жыл бұрын
Keep weldin' bro, shirtless.....hella cool
@BobVerwey2 жыл бұрын
@@rodalo1636 LOL I'm from Africa. I have a thick skin...and anyone who builds a conveyor is a boss..so keep on trucking..
@rodalo16362 жыл бұрын
@@drelaw2002 Thanks Andre, all the good vibes to you
@TV-jf9so8 жыл бұрын
ممتاز
@pillashsd58363 жыл бұрын
Excellent ... Sir... I'm searching how to make convey belt structure .. I'm lucky to watch video .. really I like it .. way of making I'm planning to make ..new conveyor belt ...flat I need ur help for technically ... Can u provide urs mail I'd.. or whatsapp number.. If I get ur support .. easily I can make it ..pls sir.. I'm from india .. Regarding my poultry I have to need conveyor .. I have
@rodalo16363 жыл бұрын
Sure, these days I'm a bit busy but I'll do what I can. Many greetings, Rodrigo. rodalo1636@yahoo.com
@pillashsd58363 жыл бұрын
@@rodalo1636 Length 50 feet Width 1 feet Height from the floor 3 feet Flat conveyor belt ... Weight 150 kg (feed bags will go on that belt.. 1 bag weight 50kg ) Can u tell me ..which material required ...with Specification