Homemade Hydraulic Vise

Thanks to the use of hydraulic cylinder the vice is very and strong, the work is much faster and more comfortable. I powered the vise with a hydraulic pump driven by compressed air.
Music:
1. Cousmic - Hasta La Vista
2. Anno Domini Beats - The Truth
3. Anno Domini Beats - Lifelong
4. Patrick Patrikios - Select
5. Cheel - Anywhen - You Say
6. Verified Picasso - Yo Picasso

[@КонстантинПоваляев-м3к]

На работу мастера можно смотреть не отрываясь. Браво и респект! лайк и подписка!

[@WorkshopFromScratch]

Спасибо 😁

[@muhammadjjanwar]

@@WorkshopFromScratch ...

[@DrFiero]

I modded my cheap-o harbor fright press to use a similar air/hydraulic pump and a salvaged ram - being able to use BOTH hands, and not have the whole mess jumping around while you're pumping is SO much of an improvement! I was pressing the bushings out of my 110lb leaf springs, and there's just no way I could have held it up AND pumped.

[@spideybrent]

Hello from Yorkton, Saskatchewan, Canada. Thanks for sharing your great video’s please keep them coming.

[@silvergrizzly316]

Everything you fabricate comes out looking like a million bucks!!! BEAUTIFUL, EXCELLENT WORK my friend!!! 👍👍👏

[@WorkshopFromScratch]

Thank you 😁

[@allencarter6721]

What gauge steel did you use?

[@alexwitteried3893]

I like that he kept the ram spring accessible. That's the most likely component to wear out first meaning being able to easily replace it will be handy. As long as the pressure vessel itself holds out this will probably last decades.

[@dfairfull2542]

Well done! If you lineup the back jaws with the edge of your bench, long pieces of pipe or flat bar can be clamped from the floor up through the jaws of the vice. Cheers from Canada

[@gordonagent7037]

Great job, very practical when you need that third hand I bet. Love the attention to the finish that you give your projects. That whole idea of the ram could be used in so many applications. Thanks for sharing

[@WorkshopFromScratch]

Thank you 😁

[@maribelcandila3538]

You

[@praveenmalla7835]

@@WorkshopFromScratch how much cost sir we want that one

[@praveenmalla7835]

@@WorkshopFromScratch please sir it's very important to me

[@notthisguyagain8557]

Project was so good, that I watched the advertising. Lol. You have sublime welding skills.

[@WorkshopFromScratch]

Thank you 😁

[@DaniiLAga]

Мое уважение, это больше на искусство похоже. Прекрасная работа)

[@leemitchell3020]

I had a welding instructor when I was learning to weld in "83", he use to say " grinders and paint make a welder what he ain't" LOL. Your welds are good enough to not have to grind so much..,😎

[@vladislavborisov]

Восхитительная работа, что крайне редко можно встретить на этой хостинговой платформе!

[@getsmartr]

Nice vise. I like to use the back of the vise as a small anvil sometimes. You could bolt down a replaceable piece of hard steel there. It looks like a good size

[@WorkshopFromScratch]

Thank you 😁

[@shaunybonny688]

Could make some press brake dies for that really easily too I’m sure. Bad ass build

[@markh2128]

Very solid workmanship! Especially the attention to detail. Now if you make up a set of drawings with all the materials that would be nice. I would buy it.

[@WorkshopFromScratch]

Thank you :) I will try to do and share with subscribers :)

[@geekstudio4582]

@@WorkshopFromScratch especially the materials part. Awesome work man ,,keep up

[@ЕвгенийКосенко-ы7у]

Спасибо за увлекательное видео. Смотрю с удовольствием! Были бы ещё чертежи, цены бы вам небыло.

[@ApprenticeGM]

What a terrific vice you've built mate - superb workmanship, good design and thanks so much for sharing. I'm impressed and want one!

[@dagins90]

It’s not a vise, it’s a work of art.

[@papamalta]

Buenisimo el trabajo. Solo es dificil trabajar ocho horas con una moral de ese color

[@nikddd5524]

Не удержался зайти и поставить лайкос. Не просто, а как охренительно. Ух, огонь, браво!!!

[@abduali4916]

J

[@gregpaterno1446]

best engineer ive seen up to now

[@cvicracer]

Awesome!!! that things belongs in a museum. Its a work of art!!!

[@WorkshopFromScratch]

Thank you 😁

[@Jon-ov3ko]

PIĘKNIE I FACHOWO WYKONANE. GRATULUJĘ I POZDRAWIAM.

[@TheChube25]

Best video I've seen on KZbin, genius!

[@MachiningwithJoe]

This is a great projects. Really impressed with how it functions and you have made it in a way a looks solid and not flimsy at all. Keep it up 👍

[@rubenariza2315]

Seria muy bueno que con cada video montes un documento relacionando materiales, planos y enlaces donde compras los cilindros hidráulicos y demás, muchas gracias por tus videos son excelentes!

[@manitobaman5588]

Hypnotic work sounds and music. Quality work.

[@WorkshopFromScratch]

Thank you 😁

[@amyasseektruth8246]

you need to build these and sell them. You'd make a killing!!!!!

[@josephma5098]

I really enjoy watching such videos. better than some movies.

[@honeycuttracing]

Very cool build, seen a few of these but your design is the most straight forward one seen and really considering this as a future project for our shop, thanks for the inspiration!!😎

[@WorkshopFromScratch]

Thank you 😁

[@DanKoning777]

Now you're just showing off :) *Well done like always.* God bless.

[@WorkshopFromScratch]

Thanks 😁

[@이종오-y9c]

²

[@AM-dn4lk]

She is a beauty and definitely a keeper.

[@danielmeecham464]

Just excellent work. Here is a guy that who pays attention to detail and quality. Thanks for sharing this one!

[@WorkshopFromScratch]

Thank you 😁

[@alanatkinson9364]

You'd never know it was home made,excellent job sir.👍👍👍👍👍👌👌👌👌🇬🇧🇬🇧🇬🇧

[@HG-bs3en]

Your finishing with an angle grinder is lovely to watch. Most engineers in New Zealand are super lazy with finishing, and often leave ugly and sharp edges on their finished work.

[@teckbugz1278]

Wow! I didn't know milk was sooooo helpful when drilling/cutting metal. You really learn something everyday! Awesome project!

[@OneManEngineering]

🤙🏼🤙🏼Yeah, breast milk is the best I heard!🤙🏼🤙🏼

[@troydaigle1260]

Wow. Great job. I wish I had one. I admire people like you, that are so creative. Wow

[@aldofernandez8978]

Buenas tardes señor, lo felicito, hizo un gran trabajo, la prensa es estupenda. Le mando un saludo desde Argentina.

[@roarkemurdock3027]

Awesome video! Small tip (albeit unnecessary for this project) if you support and secure both ends of the workpiece when you cut on the bandsaw you will cut a cleaner and truer cut. As the kerf gets deep enough that the unsupported piece starts to bend before falling it changes the angle of the cut slightly on the unsupported side. Again not necessary for this project as your rounded the edges and it’s not critical

[@josephgrant9137]

I must have ONE. Thanks Der Guy.

[@rockysuperstar1]

NICE JOB . You should put a plan and Material list together for that build . :-))

[@howardgrant4254]

Yes, please. The hydraulic ram can be had from Harbor Freight but I'd like to know where you got the pedal. Great vids so far. Now I've got to start binge watching your channel too. Keep em coming.

[@WorkshopFromScratch]

Thank you :) I bought the pump and actuator from the amazon store, sample link : www.amazon.de/-/en/Pneumatic-Hydraulic-Drive-Rocker-HA1-Pump/dp/B00W76LLVC

[@bobguevs1233]

watching from the Philippines excellent job nice work...

[@andresoviedo5509]

So beautiful, I don't know what I liked more # 1 the process, # 2 color, # 3 the final result.

[@xmachine7003]

Constructive criticism- I would have drilled holes on the backing plates to rosebud weld to the triangular struts on the inside. A more solid jaw could be achieved. It is very good the way it is. Better with the rosebud. I like your work and your video format. Excellent!! Thank you,Chuck.

[@BASF111]

Очень круто😎! Я столько лет прожил и такого никогда не видел, лайк!))

[@janeycole3327]

A very classy bit of gear. I learned a lot fast. Just sad I don't have that sort of workshop. John Warner. Australia

[@danmoreton1788]

Great welding and fabrication skills!

[@brucemansfield2501]

You didn’t put the vice far enough forward on the bench to put a long piece vertically in the vice and have it extend past the end of the bench. You always position a vice that way.

[@notaname59]

Kudos for showing what music you used!

[@chrisaquino2892]

One of the best skilled fabricators I’ve seen, great idea and nicely done.

[@electronic7979]

Excellent project

[@WorkshopFromScratch]

Thank you 😁

[@navid9852]

This is great. Adding some sort of force transducer to monitor the applied force could be pretty useful.

[@WorkshopFromScratch]

Thank you 😁

[@juanpablodominguez8975]

@@WorkshopFromScratch do you sell the plans for this vice? Thanks

[@AlteredCarbons]

half inch plate ? looks great. i been looking to buy a small vise but looks much more fun to build one

[@3rdaxis649]

That's badass. Want one. Would be cool to have a pressure gauge somewhere on it as well.

[@mishathecarman4231]

Yes, agree.

[@mikebourret3624]

Nice job! would you happen to have any plans with dimensions?

[@randyerickson2154]

Why aren’t all vices like this. 👍

[@theogriengl958]

Kompliment! Super handwerkliche Fähigkeiten! Schöne Arbeit und besser als gekauft! BR from Austria

[@tattoos1988]

Very nice what a build I like the idea it’s all hand cut and welded together thanks for sharing

[@WorkshopFromScratch]

Thank you 😁

[@notasbignow1]

Dude that’s absolutely amazing wow

[@MOUNTAINEAGLES]

Excellent work!! 👍

[@WorkshopFromScratch]

Thank you 😁

[@rickyseddon4786]

Big fan of the orange paint you use for your projects 👍🏻

[@multimummitransporte]

Servus Perfekt möchte auch solch ein super Schraubstock haben 👍👌

[@MCsCreations]

Fantastic work, dude! Really well done! 😃 It seems strong as hell! 😮 Anyway, stay safe there with your family! 🖖😊

[@WorkshopFromScratch]

Thank you 😁

[@robrodriguez4866]

Probably makes an excellent press.

[@petronilhodasilva1325]

Preciso comprar a válvula do pistão com a bomba pneumática Brasil cidade americana sp

[@petronilhodasilva1325]

Tenho os pistão idralico americanos

[@Igor_Kost.]

Хороший проект! Не так уж и много на Ютюбе действительно качественного DIY, в основном всякий мусор типа "как сделать гаечный ключ из гаечного ключа при помощи гаечных ключей". У Вас же действительно годный контент, так держать!

[@CanaldoGarimpeiro]

Ficou um excelente máquina meu amigo Meus parabéns

[@ianvicedomini2648]

I have a friend who would love a vice like that. Superb engineering and production.

[@johnthompson9625]

The only thing better would have been hammered paint, for that old-school look. Awesome job.

[@WorkshopFromScratch]

Thank you 😁

[@Wingnut_Stickman]

After the lathe restore video, I was afraid you maybe ran out of orange paint! No problem though, good to see it again!

[@sergeelismar3281]

Iiii8

[@sergeelismar3281]

⁸8i8iiiii

[@umermajeed6194]

U r right

[@archimago2010]

well that was amazing!

[@WorkshopFromScratch]

Thank you 😁

[@SlickBrody]

Thank you... so much... for fully welding those joints. You just got a new subscriber, just for that. Love the video by the way

[@henriknordeng]

Love the vise. I have to build one of thoose. Really good work

[@davidfuller764]

So.. this guy shows me his experience strength and hope, I consume it, and .. yes I’m Sub’d & Bell’d but a wealth of knowledge is on this video

[@brindzapal]

I can't get bored of this videó! 👍

[@dieselwrench1826]

Great craftsmanship. Video detail steps are a plus.

[@WorkshopFromScratch]

Thank you 😁

[@glenrugh2815]

Very slick job. NICE.

[@Tramm454]

Very nice tool at the end!

[@xasanmeyliyev3909]

Большое спасибо за такие замечательные изобретения👍👍👌👌

[@nscantling]

I like the idea, the only real issue I see with the vise is that all of your clamp load is dependent on a single M12 bolt.

[@WorkshopFromScratch]

You can always increase the screw diameter :) Thank you :)

[@jeromejumeaux1181]

Super travail, incroyablement efficace. 👋👍♥️😃😃

[@ao2528]

Excellent, beautiful and powerful also, nice job done.

[@PdeeAsiedu]

this guy needs an award ...whatttt

[@mabiteahungout9246]

Super beau et efficace, bravo de Paris France !

[@ismaillouwlouwair6366]

Amazing as always

[@2campercamper]

You are an inspiration thank you for sharing your incredible talents

[@WorkshopFromScratch]

Thank you 😁

[@punkbloater]

Now that’s a REAL vise! 😊👍🏻

[@WorkshopFromScratch]

Thanks 😁

[@browill9]

Awesomeness. I absolutely love it. Thanx for sharing your video.

[@2LateIWon]

Sooooo cool. Great idea and hands free perfect

[@WorkshopFromScratch]

Thank you 😁

[@alexpsyt]

Great Fabrication skills. Nice to see!!!!!

[@khristopkel]

I love how he layered all those unprimed surfaces so the rust has somewhere to live. How nice of him

[@jrand2631]

Brilliant build, and I love the color! 👍👍👍🤩

[@WorkshopFromScratch]

Thank you 😁

[@sergeantwilliams4911]

Damn fine craftsmanship.

[@WorkshopFromScratch]

Thank you 😁

[@mtrestoration3060]

Super pratique je veux le mème 🤩optimisation du temp de travail 👍🏻👍🏻👍🏻

[@MarcoPietrangelo975]

Lavoro fantastico e spettacolare! Sei un grande!!

[@WorkshopFromScratch]

Grazie :)

[@meandkg]

This is awesome! very strong build as well

[@zasuitoka6208]

Dobrá práce, jste šikovný... Zdravím z Čech...

[@WorkshopFromScratch]

Děkuji 😁 pozdravy :)

[@michaelmcswain627]

Wow I really like that vise and it is so powerful, I wish I had one

[@nicolasvitelli7214]

La mejor morsa que e visto excelente fura de serie felicitaciones sos un genio

[@robertthompson371]

Awesome work!

[@matthewhall435]

What a amazing build great job only thing is it needs to be mounted abit more forward so you can drop stuff lower than the table and still have it in the vice 😊 but epic job 👍🏻

[@WorkshopFromScratch]

Thank you 😄

[@toninopuddori7482]

Molto bravo. Complimenti.

[@davidfuller764]

Well, that was amazingly beautiful to me!