Hi guys, here's my homemade throttle body synchronisation manometer.
Пікірлер: 22
@brent072 жыл бұрын
Thanks man I did one for my Honda cbr 1000rr and yeah, it runs perfect.
@twistedfatebuilds2 жыл бұрын
Awesome buddy, I still have it going as I run it over the K1100 every now and then to make sure everything's still good. 😉
@larryschatz29833 жыл бұрын
really good mate 😁 good one 😁😎
@twistedfatebuilds3 жыл бұрын
Thanks Larry, actually had to pull it out again the other day to check the K and happy to report it's still working perfectly 😉
@Feinrizulwur3 жыл бұрын
First see you have correct coolant for aluminum motors. Then check compression and ignition. Adjust the valves and check the fuel pressure and the air filter. THEN adjust the suction. A lot of job to build a tube checker so I built one with valves from old gas stoves and manometers I already had. BTW Check rubber houses for leaks.
@kc3291913 жыл бұрын
Good video!
@twistedfatebuilds3 жыл бұрын
Thanks buddy 😉 She is still working perfectly I've only just re balanced the TB's again after giving the injectors another clean out 💪
@williampetrey6623 жыл бұрын
Dude....bike is beautiful! Really hate that the exhaust is blocking that beautiful rear wheel. That's a good focal point of those bikes. Just my opinion. Great video
@twistedfatebuilds3 жыл бұрын
Thanks for the comment William 🙏 the OEM was only stuck on there to pass it's roadworthy inspection then quickly horse kicked straight off for a right hand conversion pipe and S100RR TERMI shorty I had already sitting patiently waiting. You'll see this in my later vids 😉
@TheCalvinSkinner2 жыл бұрын
Where did you get the little black and blue valves in the tube there?
@twistedfatebuilds2 жыл бұрын
From our local hardware store (Bunnings) buddy. They are for irrigation drip systems
@samslaby48823 жыл бұрын
Does there need to be some sort of relief valve in the system to avoid sucking the ATF all the way up the hose and into the engine?
@twistedfatebuilds3 жыл бұрын
Hi Sam, not at all buddy I actually installed some valves up the top to start with as I was worried the same thing would happen but removed them when it didn't. I had a lot of hose and draped it up over a step ladder to make sure nothing got sucked high enough. When I first did it one line shot up pretty quick but I cut the engine well before it got up near the top of my looped hose and adjusted that TB for less suction which sorted it out to balance across the others
@samslaby48823 жыл бұрын
@@twistedfatebuilds Thanks for responding so quickly. I'm gonna build using your design. It's cleaner than some of the other DIY designs on youtube. I think what I didn't understand until now is the effect of the common reservoir. If each tube had its own reservoir I think the fluid would in fact be sucked all the way up the tube. But because there's a common reservoir the different hoses are 'competing', in a sense, and so fluid can't be sucked all the way up the hose.
@twistedfatebuilds3 жыл бұрын
@@samslaby4882 No probs mate. I have seen them work by just linking the 4 tubes at the bottom too but I liked the resivor idea better so went that way and it works perfectly. Just make sure to leave a lot of tube and hang the loop up high in case you have a TB that's way out of sync as it it suck it up quickly. If it's really bad you can always bench sync them first to get close then finish on the manometer
@edgarrivera4801 Жыл бұрын
Me podría ayudar , no he podido con este sistema , el liquido me llega al motor por lo que me toca apagarlo , cual seria la solución
@twistedfatebuilds Жыл бұрын
Hi there, not sure why this is happening? You can add restrictors to the line with adjustable taps or filters to add resistance but I didn't have this issue so not 100% sure sorry.
@venanciotavares16362 жыл бұрын
Wich back rims are you using in your bike
@twistedfatebuilds2 жыл бұрын
It's a k1200LT mate. Direct swap for the tri spoke
@ModernMountainLiving9 күн бұрын
$30 Au is 1cent US. I am laughing and crying at the same time realizing this is a three year old video. That's Bidenomics working, right?
@johncooney93327 күн бұрын
Why are you being political on a KZbin video about synching carbs? You probably know very little about either subject.
@ModernMountainLiving6 күн бұрын
@@johncooney9332 Ohhhh Butt Hurt Johnny got me! Answer: Carb Synch, very little and why I am watching. Why: because I am an American Patriot that loves my Freedom and exercising it. Now I have to go act like a liberal and cry cause Johnny hurt my feelings.