How To Replace Ford Expedition Heater Core Hose 5.4 Engine

Рет қаралды 41,047

Күн бұрын

Пікірлер: 36

@HomeOwnerRepair Жыл бұрын

Buy Tools Needed For The Job 🔧BUY Replacement Ford Expedition Heater Core Hose Lower: amzn.to/3LomPLL 🔧BUY Replacement Ford Expedition Heater Core Hose Upper: amzn.to/3UXUleZ 🔧BUY Neiko 3/8 Inch Socket Set On Amazon: amzn.to/3kUuGpN 🔧BUY Ratchet Wrench Set: amzn.to/3mKWIFh 🔧BUY Anti Seize Threat Lubricant: amzn.to/3L9S3WZ

@BullTaco-no9bs 11 ай бұрын

When removing the quick release fitting you must first push the fitting onto the pipe. That will allow you to push both releases in and separate the coller from the keeper.

@HomeOwnerRepair 11 ай бұрын

Thank you for watching our auto repair video that shows you how to replace the heater core hose on a Ford Expedition. We tried that, mu truck has 200,000 on it, this may be an easier repair on a low mileage truck that is also in a dryer climate.

@SP-gz5jx Ай бұрын

Helpful video. Took me about 1.5 hours for my 2014 Expedition. Tabs on 2 of the upper hose connections would not release. Very fiddly and annoying job. I found it was better to let the tabs stay open for 10 minutes to get them re-acclimated to the “open” position. Cost me $139.45 on 9/5/24 for delivered to my house next day Dorman parts 626-642 lower and 626-585 upper, with the Auto Zone 20% discount. So, your part numbers were spot on. Thank you for the tutorial. Love your videos.

@HomeOwnerRepair Ай бұрын

Thanks for checking us out. I am glad this auto repair video that shows you how to replace the heater core hose on a Ford Expedition helped you out.

@neomatrixfree8031 8 ай бұрын

THIS was hugely helpful!

@HomeOwnerRepair 8 ай бұрын

Thank you for watching our auto repair video that shows you how to replace the heater core hoses on a Ford Expedition with a 5.4 engine. Have a great day!

@BryanSegura-ic8dr 10 ай бұрын

Great job Guys, I've watched a lot of your videos ,I just did front wheel bearings ,brake calipers ,brake hoses, rotors and pads on front of 2011 Ford epy, and these videos are big help. I'm getting ready to tackle these heater hoses. Thank You for great videos.

@HomeOwnerRepair 10 ай бұрын

Thank you for watching our auto repair video that shows you how to replace the heater core hoses on a Ford Expedition.

@uio890138 3 ай бұрын

I used a Dremel and small cutting wheel to carefully grind the plastic quick-connects until the hose pulled off. Saved hours.

@HomeOwnerRepair 2 ай бұрын

That's awesome to hear! Dremels can really save the day when it comes to tricky tasks like that. Glad you found a solution!

@austint1151 8 ай бұрын

This was so hard. I just got tiny snippers and cut the clips. Still took 20 minutes to get the angle and not slip. It's just that one back set of clips. The rest was easy. My hands hurt, my back hurts, im taking a shower then a nap. Thanks for the video. I thought i was missing something. Hopefully the dorman metal replacement lasts and i never have to do this again. One question, i have no rear heat now. Is there a check valve in the core? Guessing i put the input and output backwards. Will this cause issues with coolant getting ti engine? Not sure how the cooling loop is done.

@HomeOwnerRepair 8 ай бұрын

I'm not really sure if there is a way to mix these connections up. I would feel the hoses to see if they are getting hot when the truck is up to temperature. Watch this video then double check your connections. Hope this helps you out.

@austint1151 8 ай бұрын

@@HomeOwnerRepair you can mix them up on the rear core. It's the Y shaped line, not the T one. The two aluminum lines underneath. Same connector, the two lines look the same. Oh well, I'll just swap them and see what happens. Thanks for the reply

@twood51 11 ай бұрын

Great video help...Thank you, and good tips from the comments too!!

@HomeOwnerRepair 11 ай бұрын

Thank you for watching our auto repair video that shows you how to replace the heater core hose on a Ford Expedition

@fredfeed4766 Жыл бұрын

Those hoses are easy to put on if you just do the removal in reverse. Put the locking clip on first till it stops. Push the hose on while trying to line up the locking pin holes on the hose with the clips. They slide right on and lock in place. You also will be assured the o ring is seated on the pipe.

@HomeOwnerRepair Жыл бұрын

Thanks for watching and also the added tip. We literally tried everything. Mine were a little stubborn.

@TheDaddy. Жыл бұрын

Mines a 2011 xlt Eddie Bauer edition and it got a lot more room in the front that that

@TheDaddy. Жыл бұрын

Alot

@HomeOwnerRepair Жыл бұрын

Thanks for checking out our Ford Expedition heater core hose replacement video.

@TheDaddy. Жыл бұрын

@@HomeOwnerRepairand I had to change the first one with the 2 quick connects

@TheBayoutransplant 7 ай бұрын

Cut those sobs off, buy some 3/4" heater hose and hose clamps and replace all of that for little expense and hassle.

@HomeOwnerRepair 6 ай бұрын

Thanks for watching

@slunky Ай бұрын

I came here because someone did this on my F150 and the hose and worm clamp blew off under pressure.

@69musicman1973 Жыл бұрын

2 ways to get this line off one is the tool that's designed for it or squeeze the tab push in on the line and then pull it will leave the tab on the broad and allow the hose to come off but there's a tool no fight!!!

@HUFF-N-PUFF-2024 Жыл бұрын

Do you know where to buy the tool?

@torkewrench9191 Жыл бұрын

I need this tool asap 😮‍💨

@HomeOwnerRepair Жыл бұрын

Thanks for watching.