#honda

  Рет қаралды 53,391

Bay Viewz

Bay Viewz

Күн бұрын

Пікірлер: 60
@norcal94116
@norcal94116 Жыл бұрын
The caliper pistons was improperly wound. That will Damage the parking brake motor.
@playboy7_16_79
@playboy7_16_79 Жыл бұрын
You're absolutely correct about that. You gotta turn on the vehicle but just in the on position (don't start the car). Then you can take a needle nose pliers and turn the caliper in. Also my guy,you never put grease on the rotors .
@preetkumar9270
@preetkumar9270 3 ай бұрын
If you have a hand held OBD monitoring instrument or if you can borrow one from a friend you can put the E-Brake in maintenance mode and that will turn the motor back and then allow you to use a normal disc brake piston compressor tool to push the piston back.
@ericgardia4575
@ericgardia4575 2 жыл бұрын
Grease should never go on the surface of the rotor or the pad surface. Sorry to call you out but it’s better to know.
@velvetbear7184
@velvetbear7184 Жыл бұрын
And using old rotors on new pads causes pulsation, squeaking, and brake fade. Also have the right tools, saves a lot of damage to the car and the person fixing it.
@ScoobyGoesDeep
@ScoobyGoesDeep Жыл бұрын
​@@velvetbear7184 you don't have to replace rotors everytime you do a brake job.
@FatThumbPEARL
@FatThumbPEARL 4 ай бұрын
Can someone tell me how to get the sensor out without a hook tool?
@patlee9704
@patlee9704 2 жыл бұрын
Um. Yeah you NEVER put grease on a rotor. It will contaminate the pads but also be a possible cause for a car to not stop or at the very least reduce braking distance
@russherman3310
@russherman3310 2 жыл бұрын
I think it's brake-clean, not grease.
@gersonrivas1624
@gersonrivas1624 Жыл бұрын
What about if emergency brake warning is blinking after I'd replaced rear brake pads exactly like you did
@BayViewz
@BayViewz Жыл бұрын
I never ran into that issue. But if it happens I would suggest disconnecting and reconnecting the car battery.
@5ohmobn
@5ohmobn Жыл бұрын
I’m getting same issue any way to fix it
@cuzcraven6847
@cuzcraven6847 Жыл бұрын
What needs to be done is unplug and disconnect the parking brake motor before you compress the piston.
@theschuntz
@theschuntz Жыл бұрын
Whats the part number?
@BayViewz
@BayViewz Жыл бұрын
You would have to call or go to the dealership for that. I don't know it from the top of my head.
@jamesmonteon2787
@jamesmonteon2787 Жыл бұрын
You can get the same pads at Napa auto parts, for about 45 bucks, part act1878. Akebono makes the pads for Honda. Honda just box them in their own Honda labeled box and jack up the price lol.
@realtalk7704
@realtalk7704 2 жыл бұрын
It be helpful if someone else is holding your camera so that you can see a complete video I didn't see which way you turned the piston
@mallion7373
@mallion7373 Жыл бұрын
Can someone explain the piston part more ?.. what is the purpose of turning it ?
@BayViewz
@BayViewz Жыл бұрын
With the new braking system for the newer cars, instead of using a c-clamp like traditional braking system, for this Honda you have to turn it for the piston to go back in before installing the new brake pads. Hopes this helps and brings more clarity
@mallion7373
@mallion7373 Жыл бұрын
@@BayViewz how will I know it’s back in
@BayViewz
@BayViewz Жыл бұрын
@@mallion7373 when you see that the piston is flushed in and you can no longer turn it back in.
@mallion7373
@mallion7373 Жыл бұрын
@@BayViewz this really helped thanks man
@nickycasty9403
@nickycasty9403 Жыл бұрын
Same problem I turned the piston all the way clockwise but it stopped is it because of auto zone brakes
@julianmolina673
@julianmolina673 Жыл бұрын
I am turning the piston on the caliper however it is still not retracting enough for me to install new break pads. Any advice?
@BayViewz
@BayViewz Жыл бұрын
Use a c-clamp to pressed it back in flushed.
@michaelagostinacchio1493
@michaelagostinacchio1493 10 ай бұрын
This caliper is not a push in ,just be patient and twist it,it does retract,they do have a special tool for it or just use a needle nose pliers,it is much harder but it does work ,good luck!
@HondaMom
@HondaMom 4 ай бұрын
I couldnt even get that first screw out
@AdriansBass
@AdriansBass Жыл бұрын
6:22-6:23 you skipped like 20 steps. Come on, man.
@BayViewz
@BayViewz Жыл бұрын
It doesn't take 20 steps to change and install new brake pads. Thanks for watching!!!
@AdriansBass
@AdriansBass Жыл бұрын
@@BayViewz even if it was just one step we have no clue what you did. You have to look at it my way. For someone who or relying solely on your “instructional video” for the job it’s best to show every step. You jumped over very important steps bud. But thanks all the same.
@anon2414
@anon2414 Жыл бұрын
The caliber only turned down about a 1/4 of an inch and stopped. Not turning anymore. Do you have any suggestions. Car ignition is on and e brake is off
@BayViewz
@BayViewz Жыл бұрын
You're talking about the piston right? Try using a c-clamp to pushed it back in fully.
@nellof1244
@nellof1244 Жыл бұрын
Car does not need to be on and should not be. They sell a cube at the auto parts store that I'll match up with the dimples you put it on the end of a 3/8 ratchet push in and twist at the same time. If you want to spend a 100 bucks or more they sell other tools to compress the piston. Places like autozone will also rent it to you for free
@anon2414
@anon2414 Жыл бұрын
​​​@@nellof1244I took off the electric brake plastic part from the back. You need to twist the spline bolt then you can compress the caliper. Other videos show you how to do that. I was using the tool from AutoZone it wasn't moving anything
@alexthegadfly
@alexthegadfly 4 ай бұрын
You need to warn people about the parking brake- if its on, and the person doesnt check it or do the old wheel spin trick, you could cause someone to mess up their parking brake sensor thus costing them $$$ to get it fixed
@Kittana1498
@Kittana1498 Жыл бұрын
Ty
@beeswax3012
@beeswax3012 2 жыл бұрын
I think you're supposed the grease the edges of the pads where it slides into the shoes. Other than that great video.
@ganshyamsukhai6364
@ganshyamsukhai6364 2 жыл бұрын
If u grease the clips you're creating an area to collect dirt and debris. Deff not suppose to smother the back of the pads with grease either
@kimquyluu6771
@kimquyluu6771 2 жыл бұрын
Thank you share clip
@BayViewz
@BayViewz 2 жыл бұрын
You welcome
@kimquyluu6771
@kimquyluu6771 2 жыл бұрын
@@BayViewzI am vietnam
@BayViewz
@BayViewz 2 жыл бұрын
@@kimquyluu6771 nice to meet you sir. Thanks for watching.
@bigdaddy8286
@bigdaddy8286 2 жыл бұрын
Bro u said I don’t have a 7mm so we just gonna use this. Lol what size did you use
@BayViewz
@BayViewz 2 жыл бұрын
I believe it's a 7 mm Allen key. If you have a set try it out. I might he wrong as I did this video months ago lol. Sorry if I'm wrong.
@alexzaragoza9834
@alexzaragoza9834 2 жыл бұрын
The piston I did not turn it how you did with the pliers I just pushed it straight back , and my brake light on the dash board is blinking do you think cus of that ,? My electric brake still works tho
@BayViewz
@BayViewz 2 жыл бұрын
I turned it with the pliers and then when it stopped turning I used a c-clamp to pushed it back in. What you did probably triggered it. I would scan the car to make sure there are no codes and disconnect the car battery for a few mins to see it the brake light on the dash stops blinking.
@prestonmiller7749
@prestonmiller7749 2 жыл бұрын
Do you have to turn it a certain way? Counter clockwise or clockwise?
@vigourdiy5084
@vigourdiy5084 Жыл бұрын
@@BayViewz The correct way is to use a diagnostic tool to put the brakes in "service mode" then manually turn the piston back clockwise or counter clockwise, it depends on make & model. If you dont you can definitely damage the piston or the actuator motor & its internal parts/gears. These caliper motors are built with "limit stops", so if the brake light is flashing it's possible the cars system cant correlate with the rear brakes & it's actual position. You may have to "relearn" the system.
@Thomasrulesrs
@Thomasrulesrs Жыл бұрын
@@vigourdiy5084 there is also a way to put the electronic brake into “maintenance mode” to c clamp the piston. I don’t find the pliers to be efficient or trustworthy enough to not damage the piston.
@lsay24
@lsay24 8 ай бұрын
I can’t even see anything past 5 minutes. You skipped a part and your arm blocks the camera
@CounterStike24
@CounterStike24 2 жыл бұрын
More helpful than damned autozone
@BayViewz
@BayViewz 2 жыл бұрын
Bro 😆
@ronjoseph5601
@ronjoseph5601 2 жыл бұрын
You grease the brake pads wrong bruh….is this your very first time
@slumygoat
@slumygoat 2 жыл бұрын
He greased the backing of the brake pads not the contact side. It is perfectly applicable and recommended when changing pads ! To ensure noise and vibration free braking.
@ExcaliburTTP
@ExcaliburTTP 2 жыл бұрын
at least he didnt grease the pad materials
@playboy7_16_79
@playboy7_16_79 Жыл бұрын
​@@ExcaliburTTP he put grease on the rotors,it's still going to get on the pads 🤔
@playboy7_16_79
@playboy7_16_79 Жыл бұрын
Never put grease on your rotors !!!
2019 Honda Accord Rear Brake Replacement NO SCANNER REQUIRED.
19:28
Dan The Brake Man
Рет қаралды 2,5 М.
coco在求救? #小丑 #天使 #shorts
00:29
好人小丑
Рет қаралды 120 МЛН
My scorpion was taken away from me 😢
00:55
TyphoonFast 5
Рет қаралды 2,7 МЛН
Мен атып көрмегенмін ! | Qalam | 5 серия
25:41
4 Ways to Retract Brake Piston on a Honda Accord with Electronic Parking Brake
18:54
Changing Nissan Tiida (versa) Caliper, model year 2007.
6:57
Jus d' great.
Рет қаралды 26
Bigger Engine.
2:03:51
SimonFordman
Рет қаралды 279 М.
2012, 2013, 2014 and 2015 Honda Civic Rear Brakes Replacement.
6:38
Mundo The Fix It All Guy
Рет қаралды 112
By Recycling Iron to Complete the Process of Making Motorcycle Wheel Hubs
15:57
coco在求救? #小丑 #天使 #shorts
00:29
好人小丑
Рет қаралды 120 МЛН