Honda Goldwing | Remove Carburetors 🛵

Hello Everyone! It has been a while since last upload.
This is a part of the fuel system section of the project. I repaired the gas tank so no it is time to work on the carburetors.
In this video I remove the carburetor assembly for cleaning and rebuild. It can be a little bit of a pain but not too bad. Removing the carburetor assembly from the Honda Valkyrie is much more of a pain!
I hope this helps with your bike project!

[@masongrace5670]

I cant tell you how much this video helped me, never worked on an engine before but started working on a 81 gl1100i that hasnt run in 15 years cheers man

[@TomAsay64]

Thank you so much! I’m glad that I inspired you to start working on your bike!

[@DTBaker-gq4fd]

Doing my GL1000 carbs tomorrow. Have only ever replaced throttle cables, so this is very interesting. Thanks for the excellent video.

[@cncbuss1]

Great views on how to do this. Thanks Tony! Cheers from Montreal, Canada!

[@TomAsay64]

Thank you! Greetings from Florida!

[@davycrockett8752]

Thank you for your thoughful and succient work Brother.

[@TomAsay64]

You are very welcome! Thanks for watching!

[@jasonlandry1503]

Awesome,just picked up an 82 gl1100,very helpfull

[@annielamote6046]

Bedankt Tom voor deze opname!prachtig uitgelegd,veel van geleerd,grts robert

[@TomAsay64]

Je bent van harte welkom! Bedankt voor het kijken!

[@TechnMoto]

nice breakdown. at some point I will be using this info. thanks

[@TomAsay64]

Glad it was helpful!

[@jurgenschneller8478]

Very well done! So good for me, to learn! Many thanks!

[@TomAsay64]

You're very welcome!

[@Akifrend]

In the case of GL1000 it is nor necessary to remove the intake boots, just rotate them, you neither need to remove the vaccum covers, but it is easier to remover the carbs if you remove the small vaccumm valve. just some tips from my experience, thanks for sharing this video

[@TomAsay64]

I did try with the vacuum covers on but it was just too tight for comfort. Rotating the right side intake boots may have worked but removing them just made it easier. There may be more space available on the GL1000. Thanks for the info and please keep the tips coming! I’m glad you enjoyed the video!

[@Britcheflee]

Excellent - just how a to do video should be done - saved it for my upcoming job.

[@TomAsay64]

Awesome! Have fun on your upcoming job! Thanks for watching and saving! There are two more videos on the carbs as well.

[@jamespolucha8790]

Man I was fighting with the cables with the carbs mounted , I’ll have to try your way, thanks

[@TomAsay64]

Those cables were a pain!

[@williamchristie7365]

Excellent video. I need to replace the fuel line from the fuel pump to the carb assembly. It looks like the same hose you left connected. Is it possible to remove that hose without removing the carbs?

[@edwardallan197]

Thank you. Will be doing it all very soon.....

[@TomAsay64]

Best of luck!

[@williamgibbs9672]

Excellent job!

[@TomAsay64]

Thank you very much!

[@Rambo-lc5bl]

Thanks so much very helpful information

[@TomAsay64]

You are very welcome! Thanks for watching!

[@Akifrend]

Yours is a bit different to my 1976 wing

[@TomAsay64]

Yes, there probably is a difference because of the year and the size. As I replied above, I did try what you said. Thanks again!

[@RochesterAstro]

why do repair guys always play music , I cant hear what hes saying

[@RuhRohRaggie069]

thank you I have Clymer for my 83 aspencade but its photos are so dark its all but worthless but you covered it all my friend

[@TomAsay64]

Great to hear!