Honda K Series Cam Cap Torque Sequence / Specs

[@jamespatterson9446]

Wish other folks videos were short and to the point like this one. Much appreciated 👍

[@AdrianoPereira78]

Thanks from Brazil! I owe you several beers.

[@Jana-zo8uq]

Weres the number 10 socket bolt at cant see in video

[@sanuyapaul1759]

Thank you... And which cylinder head bolt on Honda crv rd1 am i going to unscrew first, second, third, fourth, fifth, etc.

[@jjh.v]

One of my studs got stripped for my valve cover. Is ok to loosen the cap bolt just one? Will affect the engine or not? Or do I have too loosen everything in sequence then re-tighten everything.

[@johnwatson-sw2ql]

Is that last 10 mm bolt that you put in important or can it live without it? The reason I asked is when I took mine apart and didn't have a 10 mm in there, it was just empty

[@hondaresource]

I’ve seen a lot without them. It’s fine without it

[@dlouis1830]

If I loosen these could I rotate a cam shaft sprocket that is locked up back to TDC? Much appreciated

[@ryleepowers]

i didn’t have a torque wrench on hand so i tightened these all good and tight with a 1/4” drive ratchet lol. I’m a bit concerned is there any way it could do damage to the cam if they are too tight? They are definitely tight enough not on the loose side.

[@hondaresource]

They'll probably be fine

[@ryleepowers]

@@hondaresource thanks for the reply. I started it up about an hour ago after allowing the rtv to dry for a day on my valve cover and it seems to run great.

[@stevenreinke5706]

I have a 2013 CRV is the torque and sequence the same as on this engine.

[@hondaresource]

Yes, should be

[@hassanmohamed8904]

Thanks for the video, after tightening one of the bolts, I can see air bubbles coming out at the bolt head, what would be the reason?

[@hondaresource]

It's just oil from the bolt hole coming out

[@hassanmohamed8904]

Thanks a lot for the quick reply. So this's okay? I keep hearing from others that this can be due to a bad head gasket.

[@hondaresource]

@@hassanmohamed8904 cam cap bolt holes have no relevance to the head gasket

[@osvaldofrancoperez38]

Hello for a Honda 2.4 2009 ? It should be the same that one has 23 bolts I think

[@hondaresource]

yes, same thing

[@osvaldofrancoperez38]

Thanks for responding

[@israelrosales4021]

Amigo me regalarias los torques de biela y bancada de ese motor k20z3 😅

[@jcarlos462]

what is the torque cam caps honda crv 99 ?

[@hondaresource]

8.7 ft/lb

[@cristianluevano8623]

Yk the camshaft torque specs for a Honda Accord 2008 3.5L ??

[@hondaresource]

are you referring to the gear onto the cam?

[@idrcookiez620]

Hey man, so I stripped the nut on one of those studs for the valve cover. So I took that bolt out and I replaced it with a new one, torqued it down to 15ft and the first click snapped the bolt. Do you think this happened because I replaced just one bolt and didn’t do the sequence? Or maybe it was my torque wrench??

[@hondaresource]

15 ft/lb shouldn't break one of those bolts. May want to check your torque wrench

[@idrcookiez620]

@@hondaresource so without doing the pattern and just replacing one of those bolts it shouldn’t have broken?

[@hondaresource]

@@idrcookiez620 definitely not

[@vincentwelshman8435]

What was the torque spec I couldn't hear ?

[@hondaresource]

16ft/lb

[@Resistculturaldecline]

Do the cam cap fasteners require threadlocker ?

[@hondaresource]

No sir

[@Resistculturaldecline]

@@hondaresource Thanks for the quick reply 👍

[@yusofahmad4675]

Torque for cap cam b16b?

[@hondaresource]

Should be same as all b series vtec heads

[@shawnaking4652]

What about torque specs for a 2006 honda accord 2.4 motor cam shaft

[@hondaresource]

Same as this one

[@bthompson1767]

That torque wrench clicks alot

[@hondaresource]

I need to invest in a new one for sure!

[@Almostboosted]

Awesome thank you

[@clintavo]

Thank you!

[@hondaresource]

Hope it helps

[@Dc5Knightv2]

Thanks

[@hondaresource]

Welcome

[@EdgarARomeroOrellana]

2006 acura tsx is the same pounds of torque

[@hondaresource]

yes.

[@kevinilg2657]

Thank you 👍