Seriously. Thank you for this. I been procrastinating cleaning behind the front sprocket cover specifically because I saw the clutch system attached and was worried there might be something I wasn't prepared to deal with when taking it off. ❤
@Motourev Жыл бұрын
Easier than you think buddy
@stevelutwyche4 ай бұрын
Thanks for posting this, I’ve got to tackle it on my 2002 VFR this weekend. Also, as a Brummie living in exile down south, it’s great to hear a Midlands accent on a KZbin tutorial! 👍
@garybroom84184 ай бұрын
Mate, this was a great vid. I'm just doing exactly the same on my 800Fi only taken a week! doing it on the drive between rain storms and awaiting the chain splitter etc etc. But all went well until the easy bit of refitting the front sprocket cover, and after trying to see why its not going on the last 10mm I guessed its that rod. As this has taken an age I think the piston, just quietly crept out a little each day. But thanks to you I now know what to do! Incidentally I removed my sprocket cover in one piece, so fewer bolts to get wrong ( as you mentioned I think there's three long ones, but one of these is about 8mm shorter than the others o/a length probably about 110mm, so to be just a little shorter is annoying). But I will now remove the clutch bit to push the piston back and maybe the other bit if the mounting that fits over the sprocket nut doesn't align easily. Thanks again ....rains stopped so lets see if I can do this!
@colinjarvis27392 жыл бұрын
Great job guys that's gotta feel nice to ride again now. Good tip for keeping bolts in order is to poke them through a piece of card in the same position as you take them off.🤘
@Motourev2 жыл бұрын
Great idea cheers
@TheKlunssi Жыл бұрын
Nice video, just what I was looking for. Got confused because on one page of the repair manual for my 1999 VFR it was told that the clutch needs to be drained before removing the slave cylinder, but I didn't believe that was necessary: just as your video confirmed.
@alfredopereira68842 жыл бұрын
Thanks for the video. Very helpful, particularly the link testing as I had no idea how to know when it is time to replace it.
@joshsvoss2 жыл бұрын
Thanks for making the video! I just discovered that my 98 VFR chain is way too lose. Trying to research now to see if I can remedy it or if I need to replace it.
@BRUM99225 ай бұрын
Craig i`m doing this now to mine and yes front sprocket was full of dudu, my bike has rear seat frame off as well as i found a bad earth that had melted all the way to the fuel tank pump, wires and gubbins all over the damn place lol.😁
@pitfireX Жыл бұрын
Great video fellas! Big help!
@crumblymal84792 жыл бұрын
Good one went well the old sprockets didn't look horrendous but that chain was certainly buggered ,bet it felt and sounded great .👍
@Motourev2 жыл бұрын
Feels like a new bike
@stevecavill4005 Жыл бұрын
Great vid. I'm going to be doing my Gen5 shortly. Quick question - is it ok to tighten the front sprocket against the gearbox, or is it better being in neutral and tightening it with the backwheel on the ground once the chain has been fitted. Ta.
@Motourev Жыл бұрын
I would say with back wheel on ground. I imagine against the gearbox that the gear would turn.
@martinivanov1319 Жыл бұрын
thx bro. my chain is tight>loose>tight>loose so i guess my front sprocket is not centered and i had to take that front cover. thx for guide
@kafaristm38745 ай бұрын
Tight /loose /tight means that your chain needs to be replaced. Nothing else.... Chain will stretch irregular and boom it looks like it's tight, then you will move it by half a turn and boom it's loose. Please replace it to prevent additional wear of sprockets and all of that :D
@frostbite422 Жыл бұрын
what is that plastic cover he removes at 6:09? my chain broke while riding and cracked it and I'm looking to get a replacement. future thank you for the helpful video (for when I do get around to getting another chain xD)
@Motourev Жыл бұрын
That’s the front sprocket cover
@rmtheg234 Жыл бұрын
Whats the oem linkage length for the vfr800?
@Motourev Жыл бұрын
No idea
@SaurianSoul7 ай бұрын
I'm sure you've already found the answer by now. But for future scrollers OEM is 530 - 110 links
@MatsModén6 ай бұрын
Its 108 links oem!
@dalewintle80992 жыл бұрын
Great video Craig , The AD Extreme bike cleaner did well there usally for something with heavy grease or old chain lube the Extreme chain and sprocket cleaner will shift it with ease , your new apprentice looks a bit dodgy tho 🤣🤣🤣🤣🤣🤣🤣🤣
@Motourev2 жыл бұрын
Yeah I’ve sacked him, caught him sleeping on the job 😂
@SeanieVoiceOver10 ай бұрын
Did I count 16 teeth on that front sprocket ? ⚙️ my Viffer has 17 teeth on the front but looking at some ads for chain / sprocket set kits online a lot are saying OEM is 17 front and a lot say OEM is 16 ????
@logazeuze7 ай бұрын
Not sure if you found your answer somewhere else in between but for what it's worth the haynes manual (for VFRs 2002-2009) is stating that final drive is 16/43 ✌🏻
@SeanieVoiceOver7 ай бұрын
@@logazeuze thanks 🙏 the chain & sprocket kit I ordered was 16 / 43 my mechanic messaged me saying did I want to change the gearing because the existing front sprocket was 17, turns out my speedo is accurate now with the 16 tooth front, the previous mechanic obviously gave me what he had not what I needed 😜
@Baza7652 жыл бұрын
Top job fella's,talking of brushing your teeth,if you dont get that crap up off the decking Mav,you'll have none to brush lol ;-) Ride Safe Mr B \m/
@BatterseaBill2 жыл бұрын
Should have held the sprockets together side by side to compare.
@univegymgala Жыл бұрын
What size of tool did You use to adjust te chain tension? (C-wrench)
@Motourev Жыл бұрын
The one that came with the bike
@univegymgala Жыл бұрын
@@Motourev Thanks for The tip!! I looked in The tool bag under The Seat and it was in there!!
@macidontrepost70932 жыл бұрын
be careful with old bikes our mondeo takes ages to start up probably because we go to every carboot at 7am in Skegness
@82ryans2 жыл бұрын
What did put on the frame near the seat? Carbon fiber tape?
@Motourev2 жыл бұрын
Yes just carbon wrap as the paint work was crap
@joshsvoss2 жыл бұрын
8:30 how did you keep the rear wheel still while you took out the bolts??