How to Program a Honeywell Wireless 5800PIR Motion Detector into a Vista 20p Security System using a 6160rf keypad.
Пікірлер: 24
@anthonyferrara22225 жыл бұрын
Any chance of getting those instruction in a typed out manner? Will be much easier to read as I go along installing. Thank you
@anthonyc9207 Жыл бұрын
Thank u for the video. It is really helpful. Do you have a video that shows the replacing of a sensor in an existing zone?
@johnprosser5844 жыл бұрын
Thank you. Because I want a bit more sensitivity I have programmed my 5800PIR's as Zone Type 04 Interior follower and Loop 2. During the period that the LED is flashing I am able to get a fault at the keypad. After the LED walk test times out the fault no longer registers at the keypad. If I open the case the the tamper switch will alarm the keypad and instruct to check the motion detector. I have done this with (2) detectors and currently have the zones set too 00 Not used to avoid problems. Any suggestions. I am using a 5881 ENH receiver. After determining that the 5828 RF keypad I have will not work without 2 way communication I am waiting for the arrival of a 5800TM.
@SY-gd6yc5 жыл бұрын
Question. I replaced the batt on the 5800 and followed the instructions. However now the motion detector doesn’t work or detect any motion. What is the trick to get it to work?
@Geoarm5 жыл бұрын
Do you have our alarm monitoring services?
@anthonyferrara22225 жыл бұрын
To install the wireless sensor in the video do I need an installers code or just need to enter my user code before I type in 411 etc? Thank you
@fightingmink4 жыл бұрын
How many IR sensors can we add to the Vista? I’m stuck at only adding one.
@mamiaacia61167 жыл бұрын
Help! I followed these great instructions and was so glad to find them. Before I bought the new sensor I had a "check 16" error code. After following the instructions it worked! I was able to set the alarm. But now the error code came back and I can''t set the alarm unless I bypass. Is there a way to "reset" the pad?
@Geoarm7 жыл бұрын
enter code 1, enter code 1 see if that clears the fault. If not what fault are you currently getting? Good Question on the honeywell vista 20p wired security system.
@mamiaacia61167 жыл бұрын
I entered the code then 1 twice and it didn't reset so I went in to reprogram the new areas where devices had been replaced. It does say "ready to arm" now as it had before but last time the fault codes came up again "check 10" & "check 16". It's hard to know exactly what "check" means.
@Geoarm7 жыл бұрын
Ok, check 10 and check 16 means that there is an issue with zone 10 and zone 16 it could be a battery or a tamper. Are you looking for low cost no contract alarm monitoring services? We have the lowest rates around.
@diegeo91967 жыл бұрын
Hey guys, great video! I have a question, I'm experiencing a problem which is, after following the steps you provided and added the PIR fine, whenever something is detected by it, the keypad starts beeping and not stoping, and the panel is not even armed! I have a wired PIR and works just fine (if something passes in front of it doesn't let you arm for some seconds, and nothing beeps), also added a wireless keypad and works fine too (so transceiver works fine), but I have this problem with the sensor. Any ideas? I'll really appreciate it thanks!
@Geoarm7 жыл бұрын
When is the keypad beeping what does the keypad actually say? Do you have any monitoring services with this panel?
@diegeo91967 жыл бұрын
Thanks guys! Anyways, I already figured out, it was the tamper alarm of the PIR because the cover was not in place, it sounds simple but it was difficult to spot it with a LCD panel...
@Geoarm7 жыл бұрын
That is a very common issue glad you were able to solve it. By any chance are you looking for low cost no contract alarm monitoring services? Our rates start at $8 per month for phone line and $15 per month for cellular?
@toddmason98885 жыл бұрын
Need Programming for a; self contained Mikita - Japan keypad/Motion Dector 2018 a.d. series
@jeffditlevson40387 жыл бұрын
Hey Joe, I have a Safewatch Pro Custom control panel on my ADT Pulse. Would the programming be the same sequences?? Also, I know you skipped over it in the video, but how would I give it an actual name (Front Hall Motion), etc? Great vid by the way.....best I've found to program these things. Just have these last couple questions. Thanks J
@Geoarm7 жыл бұрын
Good morning, in most cases the programming would be the same as Safewatch panels are Honeywell security systems. We usually recommend switching to our alarm monitoring services as we offer the lowest no contract alarm monitoring rates starting at $8 per month. In that fee you will also get unlimited free remote tech support where we can actually in most cases access your panel remotely or guide you through the programming very easily.
@oj94875 жыл бұрын
kzbin.info/www/bejne/o5O8iKmjqLWAgq8 or kzbin.info/www/bejne/eJaudqd9f7Kmfdk
@edsonloya3 жыл бұрын
I followed your instructions, but when I quit the Programming Mode and the 5800PIR detects an object, the panel shows a "CHECK 10" message (10 is the zone where my sensor is installed) and the panel starts beeping (not the alarm, this is disarmed). This PIR was already working and the battery is new. I tried to reprogram the PIR but still getting this message. Any ideas?
@florencet69193 жыл бұрын
I just typed in 4112800 and the panel shows No AC now.
@Rossman2U9 жыл бұрын
when I follow these instructions I get an RF:1s... what does the s indicate
@Geoarm9 жыл бұрын
Ross Man If you are getting rf troubles that could mean that the sensor you are using is to far away from the alarm panel or wireless rf keypad. If this is the case you may want to try adding a www.geoarm.com/honeywell-wireless-security-system-repeater-5800rp.html