Hoover Vision Hd & Candy Washing Machine E08 Error Fault Code Replace Carbon Brushes

[@Andeecee]

Excellent tutorial

[@stug5654]

Thank you! I disassembled mine and noticed the carbon brush had actually stuck so worked it in and out a few times to clear the dust. I then re-assembled and voila, all working again :) Only took 30mins or so.

[@sirwillsy]

Ditto! My Candy is less than 3yrs old and had plenty of carbon left. Thanks for this video!

[@Fairway689]

Hi Paul, you have just saved me the cost of bringing a washing machine repair person to my home. Thank you. Great Video, well explained.

[@pjstock135]

I have a Blomberg washer that failed. In North America they are rare and it is almost impossible to find DIY repair tips and help. Based on this video I took the plunge, inspected my brushes and one brush was completely worn down. Replacement carbon brushes are also scarce here and insanely expensive but with a bit of research I found some in the UK (where they are commonly used) and had a friend mail them to me. Reinstalled, problem solve. Bravo and thank you.

[@familyplans3788]

thanks for doing this video , after lots of swearing and cursing to get the electric connector to disconnect i , out of frustration , tipped the washing machine over on its side and saw the bushes were there sitting looking at me , as others have said i wouldnt have had the confidence to start this , keep up the great work

[@snakeywales]

Brilliant step by step instructions. Changed the brushes in our Candy Washing Machine this morning. Thank you so much

[@senarathdanawalagamageupal3869]

Thank you so much for the short & sweet video. No time waste. Good teacher, God bless you!

[@nickic8759]

Love it! Totally just repaired my parents’ washing machine. Happy with that, thank you so much x

[@susanrogerson2449]

Husband as asked me to thank you for your video , you have saved him having to buy a new washing machine only cost £8 for the brushes and about a hours work altogether .

[@How-to-repair]

Thanks please remember to subscribe as that's is was keeps this channel going. Thanks 👍

[@el_kraken]

Excellent tutorial. Would just like to add that after I installed the brushes and fixed the E08 error code on my machine, it was super noisy and started displaying an E09 error code when it entered its spin cycle, indicating some problem with the motor triac on the circuit board. After I reset the machine/ran it through self-test mode and put it through a few more noisy washes, the noise and new error code disappeared and the machine now works normally. I would wager the new brushes needed some time and a few test washes to "bed in".

[@KG-zx4mh]

I’m having same issue after replacing brushes, how did you reset it?

[@peterclegg4786]

Thank you so much, this was a really helpful video and I've managed to temporarily fix the motor on my washing machine with new carbon brushes on the way. Saved me a lot of money I can ill afford at the moment! Will definitely subscribe, cheers 👍

[@How-to-repair]

Huge thanks for your comment mate and I'm glad it was helpful. Please remember to subscribe to our channel, as that really helps us 😇 Since we work very hard in our warehouse making free video guides for you all on appliances, we always appreciate a beer, offering a choice of single or round beer. www.how-to-repair.com/help/buy-paul-a-beer/

[@pmckerna]

Many thanks; washing machine repaired for £9! Wouldn’t have known where to start without this video. 👍🏻

[@How-to-repair]

Really glad it helped you fix your problem Thank you for leaving a comment this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@ukp42]

Thank for saving me a fortune in repairs/buying new machine!

[@marcinadamczyk2431]

Thanks for that video, i can fix my washing machine instead of buying a new one 😊

[@ivanbercessy5923]

Thank You! I hav succesfully repair my cand machine, with the help of a toothbursh, hav cleaned the sgments, and the connecting carbons. And it is working now, like a charm!

[@CoutsoudisGeorge]

Awesome video thanks so much - well and clearly presented and you make it look achievable!

[@How-to-repair]

Thank you very much for the compliment. Yes my videos are very long but they are designed so you do the job correctly too many people have not got with retention span. If they can't fix it in five minutes, they just go and buy a new one that's half the problem with the world today. have a great Christmas and a happy New Year glad we could help you @CoutsoudisGeorge this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍

[@badgers1975]

Brilliant video thanks, got the bushes. 10 minute job, back up and running. Glad i came here first as Hoover's website states that it's an issue with the motor sensor and i needed an engineer. Happy wife and wallet

[@How-to-repair]

I'm glad we were able to help you if you ever need for the help we have live streams now every couple of weeks

[@monikag-s9872]

Fantastic Video! Thank you so much - my washing machine is working again! I bought you a round of beer online via your homepage! Thanks and cheers!

[@How-to-repair]

Sorry for the late reply I was away on holiday. I'm glad you sorted your machine. Have a great Christmas and a happy New Year. Thank you for subscribing to the channel

[@bcji10]

Thank you - like others here, our brushes just needed a good clean + push in and out.

[@undrahh]

Paul, you are a total legend! saved me and many more a small fortune

[@How-to-repair]

glad it helped Jayson Thanks 👍 for watching and please remember to subscribe to the Channel as that's what keeps us going in able to make the video for you

[@stephenmorse342]

Hi, thanks for the tutorial. It took me less than 30mins to extract the machine, remove the motor, clean the commutator, check the brushes and re-assemble. Boom... worked a treat. :)

[@How-to-repair]

Glad it was helpful! Thank you for leaving a comment this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@Glenn7719]

The exact same motor as what was in my mums machine, got the brushes off amazon as shes impatient and wanting next day delivery. All done and washing machine back up and working again, saves her money as she was close to buying a new one until i had a look at it.

[@eiresuduke]

Thank you! I followed your instructions and it's back up and running

[@How-to-repair]

You're welcome! please remember to subscribe to the Channel as that's what keeps us going and able to make videos for you

[@philaldo7332]

thank you, you have saved me £400 quid. many thanks

[@How-to-repair]

Glad I could help we have a live show every couple of weeks if you need more help

[@tomobrien7827]

Brilliant video. Very practical advice and instructions. Thank you very much, made it so easy to do.

[@How-to-repair]

Glad it helped

[@DirtyRockinScoundrel]

Thanks so much, fixed my washing machine with this advice. Brilliant:)

[@SnotGirrrl]

Bought you a beer, thanks so much for this tutorial! Not the first time you have saved us from the threat of having to buy a new washing machine!

[@How-to-repair]

cheers will enjoy it

[@edwarda.710]

Thank you very much, washing machine is working again!

[@samihein5441]

Thank you for the video. Fixed my Candy washingmachine 🤜🤛

[@moisesrodrigues2797]

Beautifully explained, thank you sir

[@Lorraines3DPrints]

Would this be a cause of clicking? I have a hoover dxc c49w3/1-80 machine. And with power off but door open it does some fast clicks in a 2 second burst or so. We did have e08 flash up and it stall on rinse & spin. So wouldn't finish the cycle so reset the dial to rinse and it carried on

[@hfjchan]

Thank you so much. I replaced 2 times for every 3 years already and the machine keep working just like new. But I don't know why, the second time the washing machine won't start because of the brushes is finished, there is no fault code at all.

[@johanndominik2032]

This was of so much help for me. Thank you very much.

[@How-to-repair]

Thank you for leaving a comment this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@gordonway8]

Fantastic tutorial - thank you. I want to buy the spares from you but currently showing as out of stock - do you know when they will be back in stock. Thanks again.

[@datmancunian]

Hi Paul,I've been in touch with your help desk. They were going to help me decide whether i needed brushes or the whole motor. The phone line provided doesn't seem to work. Les.

[@koshh383]

Hey! I have a Candy's Grand Evo 1702D, the machine runs perfectly, there's no problem with the rotation speed, the drying and draining is totally normal, however, when I try to use the machine on wash cycle (any), it runs for sometime but after 10 minutes or so shows E08 error. I've also noticed that the time gap between two rotations during the wash cycle is big enough 2-3 mins. After watching this video, we tried changing the carbon brushes but it's all still the same. Since the machine works fine during drying cycle, could you suggest what's the problem?

[@jamesmccarthy4455]

Cheers great video. When I restarted the machine the drum is spinning but not speeding up for the rinse cycle. Any idea why, thanks.

[@How-to-repair]

Hi, I will need the full model number of the identification plate and the details of your problem so that I can provide you with useful literature. Please use our contact us page and make sure you fill out the request for what your problem is. A video shoot of the problem would be perfect as well. I will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

[@officialmysteriousrider6327]

Ive just replaced the motor speed sensor on this model washing machine as it was displaying e08 now it spinning with the belt off but it just falts out with the belt on meaning not turning. ive looked at the capacitors on the main board & the smallest one looks black suity onit ive spoke to a local engineer on the phone explaining that the bushes looked good & motor also plus fitted new speed sensor tacho but still getting this problem do you reckon that it could be the smallest capacitor as i put a screwdriver against it & i can feel it clicking as it cuts the machine out do you reckon it could be this capacity ? ? ?

[@georgevarghese1184]

Wonderful tutorial. Thanks for this valuable video.

[@How-to-repair]

@georgevarghese1184 please remember to subscribe to our channel as that really helps us kzbin.infoe432SAb2g08 Thanks, Paul 👍

[@simonwolfendale790]

Hi, my hoover displays a E08 error half way through a cycle no matter what cycle I have it on. I've had new brushes fitted a few days ago but can find what's wrong. Any ideas would be appreciated. Thanks

[@redrazor9996]

Thank you new bushes ordered. 👌

[@How-to-repair]

Great! Thank you for leaving a comment, I would love you to leave your opinion on our poll about manufactures building in obsolescence to appliances. kzbin.infoUgkxygHomnUySd_bYjaJBdEHPO6T4dYo9Ahm and this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@redrazor9996]

@@How-to-repair yes happy to do so!!

[@boardsteman]

Excellent video Paul, saved me a fortune. I’ll be buying you a beer. I can hear the belt sounds different after refitting it though, a slight squeaking noise now. Any ideas?

[@michaelwaite6725]

Good video but don't you need to clean the armature as well ?

[@How-to-repair]

you should if very bad but this one was not not scored or damaged

[@nhaang1040]

Thanks for this video (from Ho Chi Minh City, Vietnam)

[@How-to-repair]

It was a pleasure to assist you even if you are too far to be able to sell the parts please remember to subscribe to the channel

[@stephenjoseph4561]

I have felt the washing machine to be more noisy with new brushes, is that normal .or is it bcos I'm doing somethingwrong? Pls advice

[@Fragmon1]

I have the same Problem:)

[@Fragmon1]

Thank you for the tutorial. Now it works but after replace the brush, the Motor makes more noice specialy higher sounds. What can be the problem?

[@How-to-repair]

They will make more noise while they're bedding in

[@How-to-repair]

Thanks please remember to subscribe as that's is was keeps this channel going. Thanks 👍

[@jonb705]

Thank you so much 🙏 Exactly what I needed to do really appreciate the Video 👍

[@How-to-repair]

Glad it helped please remember to share the channel is that really does help us. @user-ts7dh1rv8r please remember to subscribe to our channel as that really helps us kzbin.infoe432SAb2g08 Thanks, Paul 👍

[@lifesastitch9997]

I was getting E08 error code so I followed the steps on this vid and was able to fit new carbon brushes, although when I got it put back together it only worked once and is now doing the same thing again, same error code even though new brushes fitted. If anyone has any ideas I would be very grateful!

[@How-to-repair]

i would check motor again

[@HonestBill]

@@How-to-repair Hi Paul, I was delighted to see my machine working again after replacing the brushes. The old ones were worn exactly as you described. But, the same thing has happened with me. Strangely, it finishes the washing cycle, then shows E08. Door will not release. I then put on a drain and spin cycle which allows the door to release when finished. What is to be checked on the motor again?

[@Fordmk1]

I had the same problem with my hoover washing machine E08 code so replaced the carbon bushes as they were worn did 1 wash and it flashed E09 checked to motor again and refitted the carbon bushes and made another wash and at the end of the wash its now E08 Fault again cannot figger out what what the problem is...

[@stephenjoseph1244]

I tried to change the brush but now the Machine makes a loud screeching noise, is that normal. Will it reduce over time

[@mrdavidpollock]

Thanks so much for this tutorial. I fixed my old machine. One question though, is it normal to be a bit noisy (whiny) with new brushes?

[@How-to-repair]

Could be until they ware in Thank you for leaving a comment, I would love you to leave your opinion on our poll about manufactures building in obsolescence to appliances. kzbin.infoUgkxygHomnUySd_bYjaJBdEHPO6T4dYo9Ahm and this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@andrewarmistead7488]

I cannot find the link to the brushes but could you tell me if they’re compatible with model number wdx0c 485a 80 please thank you

[@mohang6107]

In my home I have one candy grand O washing machine, past one week keeps on buzzy noise while spinning and at the end it displayed e07 ( error). While taking out the clothes there is hot and some smoke. What should I do, kindly guide us

[@Ryan39840]

What if it's not the brushes as we have changed them

[@number9scores]

E08 only appeared when i ran the self test. Washer drained and filled but wouldnt start spin. No code shoen.

[@anthonylopes2998]

I'm not getting an error code but the drum isn't spinning, do you think it's the same problem?

[@How-to-repair]

Check the motor if it has carbon brushes fitted, then inspect them @anthonylopes2998 please remember to subscribe to our channel as that really helps us kzbin.infoe432SAb2g08 Thanks, Paul 👍

[@racheyfox9023]

Hi Paul, great video , thank you, im having trouble with the link to purchase the carbon brushes though, it doesn't bring anything up on your page, please help 🙏 thanks in advance kind sir 😊

[@How-to-repair]

sorry rachey bee having trouble with wesite lat fem weeks if you still need help contact me through please remember to subscribe to the Channel as that's what keeps us going and able to make videos for you

[@frankmurphyburr3598]

Thank you sir 😊

[@engmech337]

Hi electrolux EDC2086GDW dryer showin R 32 what is reason

[@msdb100]

I have and candy rapido 11 kg but the buttons dont operate i dont know the problem

[@uwaosasereomorodion]

Thanks for the video

[@salahmname2457]

Hello, thanks for this video. I want to please ask you. I have the error code that you have, but I did not find the product on your site. Can you help me if you have this? This is the model number Hoover HL4 1472D3 / 1 - S

[@How-to-repair]

if you fill out the contact us form I will try and help you www.how-to-repair.com/help/contact-us/ Thank you For leaving a comment this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@zayanirahal8125]

Is there a representative of your company in the Kingdom of Morocco, I have a problem E08Thank you

[@How-to-repair]

no sorry Thank you for leaving a comment, I would love you to leave your opinion on our poll about manufactures building in obsolescence to appliances. kzbin.infoUgkxygHomnUySd_bYjaJBdEHPO6T4dYo9Ahm and this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@mohmedsirajkasadiya9367]

Great job appreciate

[@How-to-repair]

Glad you enjoyed the video. I hope you manage to get your washing machine sorted. @mohmedsirajkasadiya9367 please remember to subscribe to our channel as that really helps us kzbin.infoe432SAb2g08 Thanks, Paul 👍

[@dhulme]

Thank you!

[@landrover944]

Thank-you.

[@How-to-repair]

Our pleasure! thanks 👍 for watching and please remember to subscribe to the Channel as that's what keeps us going in able to make the video for you

[@terryharkins4891]

Hi a followed your video put brushes on now saying e09 error,,

[@How-to-repair]

First thing I would check is all the wiring on the circuit board there is a chance if the carbon brushes were badly worn. You may have damaged a component on the circuit board, but without having a machine in front of me I'm unable to be much more assistance. Sorry this happened before Christmas. Hope you have a good one @terryharkins4891 this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍

[@honkytonk52]

Thanks for this

[@How-to-repair]

My pleasure!

[@twoflower8264]

Thanks mate saved me a fortune and pissed off wife lol

[@fadiamine2503]

THANKS But how could you be sur that brushes are the problem

[@pedrocruz360]

I did that, and it didn't work. What had possible gone wrong? Machine never showed E08 error again. Motor tries to start, but it stops right away

[@How-to-repair]

Hi, I will need the full model number of the identification plate and the details of your problem so that I can provide you with useful literature. Please use our contact us page and make sure you fill out the request for what your problem is. A video shoot of the problem would be perfect as well. I will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

[@landrover944]

Thank-you

[@How-to-repair]

thanks 👍 for watching and please remember to subscribe to the Channel as that's what keeps us going in able to make the video for you

[@raza786ali]

Hi dear, I like your video, excellent Can you help me to find carbon brushes for My washing machine Candy Grand Vita 8kg A+++1600 Mod GVS 168D3-80 Showing error code 08 I couldn't find in link as you mentioned in video. Much appreciated Thanks Raza

[@albertosacco9380]

Grande!!

[@SnotGirrrl]

Tried to follow all your links to purchase replacement carbon brushes and none worked at all. just thought you should know

[@cicciosinger6322]

complimenti grazie mille

[@Portugal_Algarve]

My washing machine candy display E07 and E09 😞

[@marcusflint3168]

You are an absolute lifesaver thank you so much! Get a nice blow job for this as well! Not all heroes wear capes 👍🏻

[@chrisbalanda9368]

Should kept the motor top of the machine easyer how things change

[@chrisbalanda9368]

Plastic pully keep costs down

[@SASI4real]

Porca Madonna manco il tempo di usare la lavatrice e gli è presa sta roba

[@swfcnumber1wawaw69]

I changed the motor brushes as they were totally worn down. I’ve put the machine back on and the drum is rotating now. At the end of the cycle, I am still getting an E08 Error flash up is it a case of waiting for the Motor brushes To bed in or is there something else wrong?