How i Fixed my Maytag F03 E01 Error Code

This was how i fixed my issue. It was the device connected to the pressure switch that have me all that headache.

[@WestBuilt323]

I have the same code , going to take the washer apart tomorrow hopefully I just have to clean the filter but now that I saw your video it’s more info that I didn’t know before 👍👍 Videos like these help a lot of people out there like me

[@Joricano]

That’s what did first. Cleaned the filter. Checked the hoses.. hopefully it fixes your issue

[@WestBuilt323]

Thanks for the reply , so my filter wasn’t clogged up so now I am going to try what you replaced lol hopefully that is my problem and not a bad pump

[@ronaldmitchell7654]

Thank you!!! Resolved my issue without having to do anything else! Thank you!

[@theonlygrizz]

I replaced the control board, replaced the pressure switch, cleaned the trap, and cleaned the "air dome hose" and its attachment that you mention. Same codes remain. I'll purchase a whole new "air dome hose" and cross my fingers. Such a tiny hose for $40, what a rip off. Thanks for the tip; something else to try.

[@bethsytsma8359]

Any updates on this?

[@theonlygrizz]

@@bethsytsma8359 Being on a well, the specific issue I had was at the inlet of the cold water (where the cold water hose screws into the machine to provide water). The screen/orifice was clogged BIG TIME and the machine essentially sensed there was not enough water being supplied. I replaced that contraption (has both cold and hot inlets with some solenoids on top) and BOOM problem solved. I think it was $40 us on Amazon.

[@bethsytsma8359]

@@theonlygrizz thank you, I appreciate it! I'll check that out as well.

[@2kviper877]

Exactly the info I was looking for. Thanks!

[@Joricano]

You’re Welcome..hope this fixes your washer

[@desireehutcheon5044]

Thanks! This worked for us!!

[@Joricano]

Awesome! I’m glad it worked out.

[@theonlygrizz]

After allllll my 'fix' attempts, my issue was a clogged input; where the cold and hot enter the washer.

[@clarisesandi5063]

Thank you very much

[@edwardman1742]

I hear you saying “this is my problem” and showing me an elbow, but what was actually wrong with it? Why was this the issue? How did it fail? Was it clogged, torn, leaking?

[@remegiosampayan1301]

How do i fix the f08 e4 code on the same washer

[@i2aven420]

Thanks man. Seems like my clamps slipped off

[@alexshowcase7288]

Hello... I'm having that exact same problem.... Thank you for the video... Was the part you replaced that black hose? The video was a bit dark.

[@Joricano]

It’s called air dome trap. Amazon link below Supplying Demand W10903220... www.amazon.com/dp/B083C6VLG8?ref=ppx_pop_mob_ap_share

[@mikoloe]

What did you change? did you change the hose from the pressure switch to the tub? or just the fat hose at the tub?

[@Joricano]

I changed the pressure sensor but it didn’t fix the issue. Then i changed the air dome trap and hose and that fixed the issue. I don’t think i needed to change the hose but it was cheap so i did. The part number of the air dome trap is in the comments below

[@rockerac1]

Any idea of anything else to try? I’ve now replaced the pressure switch, the hose, and the air dome, cleaned the trap. And now getting the error code again still… don’t know what else to do.

[@Joricano]

The air dome was my last try. Then i was gonna call the pros if that didn’t work.

[@alexdavis7872]

Bad ccu board the. The big gray one on the top right under the panel

[@farzaddehnavizadeh1959]

Thanks for sharing

[@Joricano]

No problem. Hopefully it helped

[@lawacesw06]

So what exactly did you replace ? Hose? Sensor? Or one way clear valve

[@Joricano]

I replaced the sensor and hose and it didn’t fix the issue. What fixed the issue was when i replaced the air dome trap

[@JJayJ]

As far as updates go, has the washer been working fine since you changed this part?

[@Joricano]

Been working ever since

[@Woody05XAM]

I replaced the pressure switch and the air dome trap and am still getting the error. The machine was draining, and I took the drain hose of the drum to make sure it was empty and am still getting an error. Any other ideas on what might fix it?

[@Joricano]

The air dome trap was my last resort. I was gonna call a service guy after if it didn’t fix it.

[@WestBuilt323]

Maybe your pump is going bad

[@jamesguralski5156]

​@@WestBuilt323can you take some of the hoses apart on 1 side and blow air through them.. ?

[@mitchnn]

What was it called and part number#. Thanks.

[@Joricano]

t’s called air dome trap. Amazon link below Supplying Demand W10903220... www.amazon.com/dp/B083C6VLG8?ref=ppx_pop_mob_ap_share

[@JJayJ]

You're a problem solver. Very helpful! Can you please post the part# and a link for it?

[@Joricano]

Here’s the Amazon link Supplying Demand W10903220... www.amazon.com/dp/B083C6VLG8?ref=ppx_pop_mob_ap_share

[@JJayJ]

@@Joricano Wow, that was fast! Thank you so much. Great video!

[@JJayJ]

@@Joricano You might want to place the link in the video description.

[@Geo-oq7td]

I replaced both switch and bottom part. Still getting codes. Yes I cleaned trap

[@Joricano]

I guess it’s time to call the pros. That was my next move if the airdrome didn’t fix my problem