How to fix Maytag washer error code E01 F09 and E1 F9.

[@rebeccaparks1100]

You are the only person on the whole Internet that had the exact washer that I have and had such simplistic instructions. Thank you so much as I have been at wit’s end for two weeks trying to figure this out. And I did not want to call a Maytag repairman because they will charge an arm and a leg and I don’t have either to spare. Your dad is a champion. And you definitely are. Thank you thank you so much!

[@killmimes]

The designers knew exactly what they were doing with the placement of the drain filter. .... It is this way so you almost certainly will have to call a Maytag certified repair tech...great job lady! You rock! And the downvoter can suck drain water

[@jcstuart6978]

what a racket! i'm in the same boat with little to no space to work with - terrible

[@derekdaling5236]

I’m sure a million people have mentioned this but there is an access panel that your bowl is sitting on. E01 F09 is the code. It is all about drainage. Tip the washer against a wall to access the bottom panel with 1/4 nut driver.

[@luism7328]

Do You know what F08 E00 is about???? Thanks so much

[@RebbleRabb]

Wow, much simpler than I thought. You saved us money and clothes!

[@GrandTheftWatto]

This worked for me! You saved my family a service call - thanks!

[@BeckyGarcia-ku3bl]

Thank you! Your comment that they should make this easier to access is 1000 percent correct! I can't believe it pulled your underwear in there! Unfortunately, my units are stacked so I can't get to the back very easily but if I can get a repair man out at least I'll know to ask if they can fix this. Other models had this "coin trap" in front but this one is crazy difficult to access! You're a rock star!

[@GroProOrg]

Thanks for making a good visual video showing us all you did.

[@williamfatta4255]

awesome video thanks for taking the time to make this!

[@janetdurham621]

Thank you! This is extremely helpful.

[@janemary8795]

Thank you for posting. It really helped

[@killmimes]

Ok,though my Maytag is similar to yours, I found out that on my unit drain filter faces forward. I bested the engineering demons today! With my mighty hole saw of justice...I cut a permanent access port on the front of the unit! Tremble before me Maytag and weep!

[@suburbanwisdom]

Well done and great commentary! I just cleared ours and hoping to be able to reset the washer, but so far it still won't start.

[@truebluepatriot2739]

Was probably the pump..

[@tonynguyen7966]

Thank you so much for this video , I solved my problem 👍👍👍

[@lourdesislas2941]

Thank you so much 🙏🏻

[@jones1394]

Thank you for the video and instructions. I look everywhere how to fix my washer and you was the only one spot on🙂. I like part pulling the panties leopard out LOL 😆 but seriously if it wasn't for you I would still be lost. Great video and problem solved. Take care ❤ 🙂

[@borg7ofnone]

I have to say you are awesome thanks for the info

[@shannonlee1010]

I bet this is my problem! I'm going to try this right now!!! EDIT..... IT WORKED! Yay! I'm so happy! Grose 3 yrs worth of lint, wrappers, coins, oil and vinegar packet lol. 😁💪

[@kararothe7019]

Baha 8 years here

[@mrslalaolds]

Good video, valuable info! Had I known about the filter, and the difficulty of reaching THIS one, would have chosen a different machine. I run two loads a day. This one grows MOLD like crazy. $200 for a new rubber gasket (over and over) but doesn't fix the mold growing factory (it's in this hard to reach filter.) Ridiculous design. Must be to keep their 'certified' techs busy. I call scam.

[@killmimes]

I would take the filter with the gasket to AutoZone ormothe auto parts store and ask them to match a gasket...

[@Kepe63]

Just an FYI, there's another KZbin video that shows you the correct positioning of the guts of that drain plug so you won't get clothes coming through it. Yes it could be easier but it's really not that hard to clean. Seen way worse

[@parsapersian80]

You are amazing. Thank you It's a terrible design.

[@Amazingrace32511]

thanks You saved us with this video

[@w5cdt]

Thanks! good job!

[@hunter8turkey1]

Thanks So Much

[@EricB-somejibberish]

thank you, just got the error

[@Dieppaloveplants]

Thank u so much i have same washer but in white and have same issue tomorrow i will be doinvg that i fix my dryer lol too have same code

[@tonymackey370]

Thank You

[@martinvalencia535]

Thanks for the info

[@jereksliwinski2789]

Thank you! 🥂

[@feedyourhead7464]

Thank you

[@zonianinexile]

Love a self-sufficient woman!

[@samakram3992]

Next time, just tilt it back ward, and open the panel underneath, with 4 screws and you can reach this part trouble free,

[@rebeccaparks1100]

This particular washer does not have the toe kick panel underneath the door. My last front loader did and it made clean out so much easier. This video is correct, there is no way to access the clean out filter without going in through the back panel.

[@mrstiffanyalexandrashain4489]

I also have the exact washer with the bottom part.. I forgot about doing it from the bottom this second time around and only remembered when I was like wow I don’t remember the motor looking like this lol 😊

[@haroldkline4898]

That is called a torx bit dear. Just fyi. Nice job, btw!

[@rushangadhuria2676]

Hey what size drill beat did u use

[@jimjohnston7688]

Found about $2.50 in loose chance, car keys, drill bit, tweezers, etc in the filter. Clearly I need to empty my pockets before washing.

[@aliveli3519]

i opened mine from back surprise!!!I guess after these helping videos they changed its place! my filter was looking front and it was all the way front end!!! I could reach with my arm but not seems possible to take it out or clean it from back!!!don't know what to do!!!

[@analtofsomeonenamereece7520]

I just tried this and only the cap came off. The trap wasn't attached. Don't know how to get the rest out

[@EdWard-ju2gh]

If your washer is eating clothes I think your issue is something else? Have you talked to Maytag about this? Also when you do this you should go ahead and rinse your line buy dumping water into the tub and letting it drain back down into your bowl. You'll be surprised at much loose gunk is still in there. Great instructions overall.

[@mrstiffanyalexandrashain4489]

Yeah but that’s assuming the line is long enough

[@wmweber91]

I just run a clean cycle in my washer after. I add a tab bit of dawn and vinegar to my load every now and then and that helps to keep my lines from being gunky. The only time it stinks if something’s is physically blocking drain.

[@Weedledeedle3]

What if it’s being stubborn to turn? What can I do ?

[@truebluepatriot2739]

Use 1/2 warm water and 1/2 white vinegar t clean all parts of the trap inside and out to get rid of the smell and mold.

[@wmweber91]

I’ve been doing that with a squirt of dawn and it works great! I only notice a smell if the line is physically clogged.

[@candicew.957]

Have you gotten the error code FL LO? This is my issue I’m going to try this method

[@candicew.957]

Also when I turn water off am I able to easily remove those silver hose and connect them back? Should I remove it from the washer or water knobs? I’m asking because when I pull my washer forward it’s pulling not enough room

[@laredodl]

I made my own fix. I can send you a photo if you want

[@killmimes]

I want to see!

[@charlesstuart6882]

T15 or T20 the T stands for Torx

[@debbiemoore7580]

I HATE THIS MACHINE!!!! Why would they ever create this stupid thing!!! I am 66 years and not able to this!!!

[@DineshPatel-lc4no]

The older machines have a little door access to filter, they did this so we would have to use their services (what a rip off)

[@ericlakota6512]

My maytag you needto take the whole front off because the drain trap is pointed front its nuts and you cant get it from the front eather

[@DineshPatel-lc4no]

Mines the same way, I told my wife I’m gonna cut a door in front so I don’t have to take the whole thing apart

[@curtisabshire5997]

The only thing I found in mine was about $2 in change

[@dsmeadows2848]

Maytag used to be a good washer.. These front loading washing machines are made to break and to have so many service calls for this Horrid Design.. My last washer lasted me for over 40 years, but this new one is non stop trouble. Under ware, socks, and any other small item will get sucked into the filter then you have to be able to move your washer to get the back off of it and clear the filter.. Over and over again.. This is non stop and happening all the time.. Maytag is not the high quality it used to be, non stop service calls.. This kind of washing machine is expensive to have if you can afford all those service calls... I am an old lady and I cannot move that damn washer it is too heavy.. and I live on a fixed income.. Don't buy this washing machine it is nothing but trouble and expensive.. I have used most all types of washing machines from the old wringer washing machine to top loader and never had trouble like this with a washing machine.. I bought it because it uses less water than my old top loader.. Save yourself the trouble and non stop trouble this machine has. Don't buy it , it is not worth it.. It is JUNK.. Who ever designed this washer put a lot of cheap plastic parts and they hide the filter clean out so you have to call a service repair person.. I have cleaned this filter so many times for a sock or under ware.. It ruins anything sucked into that filter... A washing machine that breaks at least 5 to 6 times a year.. Minimum payout for repairs are $150.00 .. And it is that damn filter..

[@wmweber91]

I have started using laundry bags for socks and undies and I get the code much less often!!