NOTE CHOKED AND CHOKELESS CARBS the primer bulb ONLY primes the carburettor, it doesn't add any fuel to the motor. Two or three slow revolutions of the motor via the pull start will draw the air and fuel mixture into the motor and will prime the engine ready to fire. Then retract the pull start fully and then pull up till you feel the resistance and compression, just after TDC allow the pull start to recoil, then one swift pull will start your engine. The method mentioned above is the best way to start these engines, as you prime and oil the engine case with slow pulls. Hardcore yanking on the pull start can cause scoring from dry piston rings, and more likely to damage the pull start itself either snapping the cord or breaking the plastic part that engages with the flywheel. Please Haggard if your going to educate your thousands of followers, do it correctly 😊
@HaggardRC4 ай бұрын
Let’s agree to disagree. I don’t overthink things (generally) in my opinion your way is overthought to make it seem more complicated than it actually is lol. Which is exactly why I made that video.
@SNAFU..4 ай бұрын
Hahaha!hee! Someone else has noticed the amount of BS that comes out of Benjamins cakehole....
@SNAFU..4 ай бұрын
Matt has finally noticed the amount of BS that Benjamin spews from his cakehole....
@SNAFU..4 ай бұрын
@@HaggardRC let's all agree that Benjamin is a donkey......
@SNAFU..4 ай бұрын
@@HaggardRC Let's all agree you are a Muppet.....
@s.o.sSavage4 ай бұрын
This is also useful to know for people who have petrol garden equipment 👍
@HaggardRC4 ай бұрын
It is indeed, I spent a lot of time explaining and explaining how to start strimmers on the golf course lol
Good for RC fun I had being playing with my RC for a while glad to find back to see your video in e back home 🏠
@mikelozza60744 ай бұрын
have you got flying a helicopter in your notebook?
@HaggardRC4 ай бұрын
@SNAFU.. Glad you’re looking forward to it, it’s coming and it was great fun! Only went through 2 sets of blades as well. 🤡
@SNAFU..4 ай бұрын
@@HaggardRC Muppet!
@SNAFU..4 ай бұрын
@@HaggardRC Benjamin the donkey lying again.......
@lottiecooper6094 ай бұрын
Good afternoon my friend, my name is Ralph and I spoke to you recently about my cen Ctr 5.0 I picked up from a friend a few weeks ago. I need a part for the carb. The carb has a round shaft that slides in and out and on the end of the shaft there is a fitting I believe it's called the carb throttle arm that I need. It has a grub screw on one side of it and a ball end on the other that snaps onto the linkage going to the throttle servo. I tried a 3.3 Traxxas carb throttle arm but it's to small. If you have one or know anyone who has one I really need this part and will gladly buy it from you. If not can I use a different carb or can I use a different motor? I don't have a clue because I'm new to nitro and don't want to buy a motor that won't fit. I now have about $750.00 invested and can't drive it. Please help me if you can. I don't even know what glow plug to use because all the books that came with the car tell me nothing. Sorry if I'm bothering you. Thank you my friend.
@alexgarrod90934 ай бұрын
Swwet bud put exust ends one mine put new pull starter on hsp broke today on run and gladiator truck think rush need adjusting Couse using 25 20% gone too only run if tev it keep it idle less plug bit warm