How to add a monitor module/pull station to a already programmed fire alarm system

[@vrryan6]

That scene with the camera zoomed in on the keypad with the lights out looked really cool

[@dutchwolf2675]

I like how you corrected at 7:07 instead of writing a correction text on the screen that you voice corrected it.

[@nics-systems-electric]

It was pretty freaking stupid I know I was in a rush actually that’s a lie I was just getting mad and I couldn’t figure out the text and getting rid of that section of audio without getting rid of that section of video so that worked LOL

[@lumenfirealarms]

You won't erase your programmed devices when you use autoprogram to add new ones! Although I always prefer using the software this way I can have the new data base backup! Cool video stay safe and have fun!! ...

[@nics-systems-electric]

I didn’t know that I thought in order to do auto program you couldn’t have other devices already installed in the system

[@lumenfirealarms]

@@nics-systems-electric yes, when you have a system with a lot of devices autoprogram is the faster way to check that all of your devices are communicating correctly then using the software you can just edit and configure types of codes labels etc, and once they are programmed in your panel you can keep using this feature autoprogram to add new devices you just need to keep the devices with loop voltage if not the panelwill tell you device L1M9 is not communicating do you wanna erase or keep it! But you can try next time my friend!! Stay safe and have fun!! ...

[@nics-systems-electric]

@@lumenfirealarms ok maybe I’ll do that I will be installing a control module soon

[@FireTech7]

@@nics-systems-electric i know if you do it on a silent Knight system, it Puts all points as unused and reprograms everything and monitor modules will all be set to alarm I've never dealt with a Fire-Lite but that's how it is for me

[@Exotic_lifestyle_palmbeach]

Good video 🎉

[@willlatino]

Can you explain class A and B loop and give us a visual how it will look. Thanks. You been great help

[@nics-systems-electric]

Yes probably should do that sometime

[@Fahrenheit4051]

What is the correct procedure for disconnecting power? Is it correct to disable power to just the loop you are working on, or the entire panel?

[@ThierryFam]

I will have that panel one day

[@peezyy3]

Hey, awesome video man. I have a dumb question about the resistor that caused the alarm. Did you put the 47k ohm resistor on the actual pull station, or did you place it on the module?

[@nics-systems-electric]

It goes on the pull station

[@minnesotaoutdoorwarningsirens]

Serious question: why do you have the panel mounted so high up?

[@nics-systems-electric]

It's not that high seems pretty normal to me

[@biohazardforce4805]

when it comes to installing stuff this is were my knowledge ends i have a question are you a tech?

[@nics-systems-electric]

No

[@jakeelliott9285]

What made you replace the panel anyway?

[@nics-systems-electric]

Like I’ve said I switched it out because I wanted to have an addressable system gives me a lot of opportunity to make more content

[@tariqulislam6341]

Can you explain INV ID of control module.

[@nics-systems-electric]

Means the point is set to the wrong device from what is actually there say the point is set to a smoke detector but you have a heat detector that would come up with an invalid ID

[@tariqulislam6341]

Yes. I have replaced the monitor module with the control module. Is there any option to normalize it from the panel.

[@tariqulislam6341]

Plz replies this .

[@nics-systems-electric]

@@tariqulislam6341 What do you mean by normalize it just set it to control module instead of modern module and it will get rid of a invalid ID trouble

[@nics-systems-electric]

@@tariqulislam6341 What do you mean by normalize it just set it to control module instead of modern module and it will get rid of a invalid ID trouble

[@VOLTRONDEFENDER4440]

was the tower pull station stil the same edwards 270spo?

[@nics-systems-electric]

Yes

[@VOLTRONDEFENDER4440]

@@nics-systems-electric I’m guessing you couldn’t remove it because Tom the silicone caulk on the side of the pull station

[@nics-systems-electric]

@@VOLTRONDEFENDER4440 nope I had to remove it to change the resistor on the back it pulls right off Silicone is just for sealant it does not glue it together

[@FourtyFiftyEighty]

Any plans on getting a bg-12lk weather proof pull station?

[@nics-systems-electric]

@@FourtyFiftyEighty not yet

[@firealarm300andmore4]

Cool

[@northernfs709]

I would’ve set it to hazard alert

[@FireAlert]

yea, you gota use the 47K not the 4.7K

[@nics-systems-electric]

Yep it’s kind of stupid I wish Firelite would keep one resistor value for everything 4.7 K ohm

[@FireAlert]

7:25 Woah, the polling light looks weird on video

[@nics-systems-electric]

Yeah the video was sped up so it didn’t look right

[@Aaronproductions]

Modules also do that when they are put on an SLC but not programmed in the system

[@FireAlert]

@@Aaronproductions weird, mine don't and i am using a 9200udls

[@Aaronproductions]

@@FireAlert Well, are they programmed into the system? if they are then yeah they’re going to poll normally, double poll at times; also are you running litespeed? you will get weird polling when you put an unprogrammed device on a live litespeed SLC.

[@nics-systems-electric]

@@Aaronproductions The only reason my looks weird is because the video was sped up

[@davienrivera1567]

Oh no fire alarm

[@Fire-hq3rm]

Ok who are you and do you have any idea actually how complicated fire alarms actually are

[@camaronruss9476]

Oh wow 4 minuits ago