This small air compressor looses air too fast, so I added an auxiliary tank to last air a little longer
Пікірлер: 73
@bobbrinkerhoff3592 Жыл бұрын
I did this same thing on a larger scale almost forty years ago , running a 5 hp. 30 gallon Craftsman into a 100 gallon tank . I ran this set-up for over five years with no problems, only tearing it down when I moved to a smaller location , and we used this to mount and dismount tires up to 44 inch diameter.
@cesar8359 Жыл бұрын
That's nice, I hope mine will last that long too. Thanks for watching.
@southern_merican9 ай бұрын
did u just let the compressor fill the 100 gal in one go? or did u give the compressor a break, to keep from overheating?
@bobbrinkerhoff35929 ай бұрын
@@southern_merican let it run , it never overheated .
@oldmanretired1989 ай бұрын
When wrapping the tape on the threads, go the same direction as tightening. Keeps down leaks and makes it easier. I did the same tank set up you showed. Works great. Good video.
@cesar83598 ай бұрын
Great tip! Thanks for watching
@jrjunior0018 ай бұрын
I was just about to say that
@roberthaynie84733 ай бұрын
He is that guy that needs the liquid ptfe.
@edt52767 ай бұрын
Thanks for the video. It's surprising how much harder it is to watch a video with annoying music instead of useful narration (no offense to composer or to DJ that selected it, all music in videos is annoying). I didn't have the patience to endure the whole video. Again, thanks for the video. Just wish youtube would warn us which vids were music instead of narration BEFORE we sit through pre-video commercials.
@cesar83597 ай бұрын
Thanks for your patience in watching my friend, next time I will try my best to explain or narrate the things I am doing.
@Infidel67 Жыл бұрын
It's a good Idea and it works, have done it myself over a year now and the motor is doing fine, it runs 8 hours a day, it's just a booster tank addon.
@cesar8359 Жыл бұрын
Thanks for watching
@OnTheToolsWithSal8 ай бұрын
Tanks are sized off of the duty cycle rating of the electric motor. Twinning two tanks together might give you longer periods of time between compressor cycles but you also made the compressor and motor run longer to top off the tank.
@markluxton3402 Жыл бұрын
I had a similar idea. Check that the portable air tank has the same pressure rating. Mine is 10 pounds less than the original.
@cesar8359 Жыл бұрын
My portable air tank is rated 100 psi and the auxiliary tank that I added is rated 125 psi. Thanks for watching
@poncematagolai7456Күн бұрын
That little plug with the ring at the end of it ? Is that like a check valve?
@user-op6uv5bx1r9 ай бұрын
Thanks for the video It is better to leave the pressure release valve even in the large tank Double safety
@cesar83599 ай бұрын
Thanks for watching
@sofjanmustopoh7232 Жыл бұрын
Nice tinkering. But the 2gal compressor motor are not designed to run that long . It gonna run a lot longer 3+ 11gal , 14 gal or4.5 X longer . The throughput of the pump is still the same . You will have the first tank capacity . But then you have to wait a lot longer for the tank to reach max pressure . I would rather wait till the compressor to catch up with the 3 gal tank than 14 gal tank . It’s a good tinkering .
@cesar8359 Жыл бұрын
Thanks for watching
@asid7315 ай бұрын
Stop complaining about the music and just mute it if you don’t like it. He doesn’t talk anyways.
@alanmajors9100 Жыл бұрын
If anything, I'd say you are smoothing out run cycles for the little pump. How frequently and for how long does the pump run under similar loads with or without the extra tank?
@cesar8359 Жыл бұрын
If without the extra tank, it will take less than 6 minutes to run. If the extra tank is added it will run about more than 18 minutes. Thanks for watching.
@davebrookbank4831Ай бұрын
Yep I am planning to add 20 gal old tank that the motor wore out on. My new compressor is quit fancy for me it is a 10 gal I believe with 2 separate connectors on it so you have 2 circuits, all I am planning to do is bore sight the old tank and clean or treat it as needed then just cut a short jumper from the new 2 circuit tank to the old one. I believe it should fill the old tank with just 1 hose and as I use the new compressor the old tank will empty into the new one as needed. I am a pretty good DIYer but I have never tried this before... I THINK it will work.
@shatnersufolanded77857 ай бұрын
Can I do this with a double stack tank from northern tool its only 90 psi 2.6 hp 4.3 gallons but I want to add a 9 gallon auxillary tank that was 125 psi. Somewhere I read you cant do it unless both tanks are within 10 psi of one another. Great video.
@cesar83597 ай бұрын
Well I just experimented it on mine and I don't condone you to do it but if you are willing to do an experiment like I did, it's your own decision. Thanks for watching
@mechanicalmonster21158 ай бұрын
I cant stop laughing at "powerfist"...
@cesar83598 ай бұрын
Thanks for watching
@SILVERK52 ай бұрын
Could you just have run the air line that would go to the tool from the original setup, but run it to the auxiliary tank (with original regulator valve fully open), and duplicate the hardware setup of the main tank on the auxiliary tank (pressure gauge, regulator, pressure valve, airline connector to tool). Am I wrong to think by doing it like I propose, it would allow to use just the original tank if you wanted to, just like before by running the airline to a tool instead of the auxiliary tank, OR using the secondary tank ? Is it because of the extra cost of the hardware to do so ? Or am I understanding this all wrong ? Also, one (major ?) difference between the original setup and an auxiliary tank is that the original tank has 2 holes it in. One with air comming IN from the compressor, and one with air comming OUT to the regulator, pressure valve and gauges. The auxiliary tank has only ONE hole it it. So it is a problem to have a potential situation where the compressor will be trying to push air in the secondairy tank while the tool will be using air, and those two airflow (in and out) will meet at the same "T" junction over the unique hole of the secondary tank ?
@cesar83592 ай бұрын
That was a massive good questions but your first question is I believe it's possible, you can do that I guess. 2nd question is also possible. 3rd question is you might be right, a good solution might fix it. Thanks for watching
@SILVERK52 ай бұрын
@@cesar8359 Thank you for the answer ! I obviously want to increase the volume of my compressor WHEN NEEDED, while being able to EASILY return it to its original configuration (nice portability of single small tank).
@ajbudda1038Ай бұрын
God bless Princess Auto 🙏😂
@cesar8359Ай бұрын
Lol... thanks for watching
@Isaiah5417GdLk Жыл бұрын
crazy, i just did the same thing the other day, only difference i left my compressor as is and just quick couple to my other tank, then barely crack the valve so my compressor gets a rest then back on again to initially fill up the second tank, once full i open the valve all the way. The reason i did this wasnt so much for all the time volume, only to give my impact more startup uga ugas. ( I don't do alot of heavy impacting,.)
@cesar8359 Жыл бұрын
Thanks for watching
@Dnasty13 ай бұрын
Hey great video. I was wondering can you swap your tanks original tank with a new one? I bought a used compressor and want to put a new tank on it so I don't have to worry about anything.
@cesar83593 ай бұрын
Thanks for watching, yes you can replace or swap the old tank with a new one.
@Dnasty13 ай бұрын
Does it require much customization? I see a lot of welded brackets and special holes.@@cesar8359
@susanfroman457 ай бұрын
helpful but would have liked to see it done.
@cesar83597 ай бұрын
Thanks for watching
@mrmotofy Жыл бұрын
Uh that's like a .7cfm compressor and will take 643 days to fill that tank. That's way over the duty cycle and will likely die quickly under normal use. Get a real compressor with 4-5cfm at 90psi or better
@cesar8359 Жыл бұрын
My curiosity brought me to this. Thanks for watching.
@southern_merican9 ай бұрын
the power of the fist is real, 😂
@cesar83598 ай бұрын
Thanks for watching
@jabsondevasconcellos3033Ай бұрын
Música boa e ideias genial 😊
@cesar8359Ай бұрын
Thanks for watching
@asid7315 ай бұрын
I want to add an auxiliary tank to my portable Milwaukee M 18 compressor. What do you think?
@cesar83595 ай бұрын
Sounds like a good idea
@chinhvannguyen16855 ай бұрын
❤ you have cfm with 2 tank? You use motor 3 HP?
@cesar83595 ай бұрын
Thanks for watching
@Mphoto73 ай бұрын
Are serious about actually helping someone? Add a simple on screen parts list/description of what parts and tools one needs to accomplish the job.
@cesar83593 ай бұрын
Thanks for watching and for the suggestions.
@fatherfoxstrongpaw89685 ай бұрын
Jeeze... my O.C.D. is fully triggered.
@cesar83595 ай бұрын
Thanks for watching
@Simracer05 ай бұрын
so wie dau Bunnes das teflon da ran geschklatscht hast,ist es kein wunder das alles undicht ist,dau bis echt a schweren dinlo
@cesar83595 ай бұрын
Thanks for watching
@Pseudoswede Жыл бұрын
But aren’t you then stressing a pump motor designed for a 3Gal capacity to 14Gal workloads? Seems like a recipe for burning out the pump motor to me. Nice try though…
@cesar8359 Жыл бұрын
It's a small pump but let's see how long it will last.
@regularpit1508 Жыл бұрын
It will shorten life but if it's an oil free design it's not meant to last long. You need to check their duty cycle if it's available. If it is an oil free design then put 3in1 silicone oil in the crank portion of the compressor and let it dry then turn it on. I would clean out the dirt from in or around it as well.
@cesar8359 Жыл бұрын
@@regularpit1508 thanks for the advice and thanks for watching
@edb95644 ай бұрын
I can't watch this with that music.
@cesar83594 ай бұрын
Ha ha... mute the audio, but I think you have already watched it. Thanks for watching.
@angelarita71836 ай бұрын
Dont like that music
@cesar83596 ай бұрын
Thanks for watching
@WobblieSkellie5 ай бұрын
Make your own video then.
@vincentpritchett12314 ай бұрын
It is pretty terrible.
@clintonpayne46905 ай бұрын
Like your show do not like the music explain yourself explain yourself on your project