How to bind SPI receiver with an ACCESS radio in D16. 📻✈

****Note, There have been some changed since this video. This will not work if you update your internal RF (isrm) or (XJT) module to any FW version 2.x or higher!****
This is not a new feature but the most frequent questions that i get is how to bind a new ACCESS enabled radio to a micro drone / whoop. This can be done with the newer breed of radios using ACCST D16 mode. Here I cover how to make that happen.
I still recommend going with an external XJT or multi protocol module to enable D8 mode. I have experienced a LOT of range and reliability issues with SPI receivers in D16 mode.
CLI SPI Bind commands based on different Betaflight versions:
For Betaflight 4.1.x type bind_rx
For Betaflight 4.0.x type bind_rx_spi
For Betaflight 3.x type frsky_bind
AND DON'T FORGET TO TYPE SAVE WHEN YOU ARE DONE!
XJT Lite: www.banggood.c...
Frsky X9 Lite S: www.banggood.c...
Mobula 6: www.banggood.c...
GetFPV referral link: www.getfpv.com...
If you would like a set of your own radio grips please visit my Etsy store: www.etsy.com/s...
Help support me by clicking through this link the next time you purchase from banggood. www.banggood.c...
These videos take a lot of time shooting and editing. If you like my content, please like and subscribe. Leave a comment if you have any questions. Thanks for watchin'!
Help support me by clicking through this link the next time you purchase from banggood. www.banggood.c...
If you really want to support me, head over to my Patreon page: / tweetfpv
If you need one-on-one troubleshooting for your equipment, come over to Discord and I can help you out: / discord
Buy me a beer or two: paypal.me/TweetFPV
Like me on Facebook / tweetfpv-100489554756112
Follow me on Instagram / tweetfpv
If you're looking for a great precision screwdriver set for working on your drones, I use and recommend this one:
www.amazon.com...
Thank you and keep flying!
Note: The links above are affiliate links. By clicking one of them before you purchase anything on Amazon, or banggood you're helping support me making videos for this channel.

[@TweetFPV]

*****Note, There have been some changed since this video. This will not work if you update your internal RF (isrm) or (XJT) module to any FW version 2.x or higher!*****

[@gabkimus7721]

i have the new version 2.15, it dont work so what is the difference in the process ?

[@TweetFPV]

@@gabkimus7721 You will need to downgrade your ISRM (Internal RF) FW to 1.1.3 to use D16 with a SPI based receiver. You can find the FW at frsky's download page for your radio click the "history" link and you'll get the FW you need.

[@gabkimus7721]

okay thank you, i will try

[@jarjarrose]

Bro, let me tell you, you are a god. I've been hitting my head against the wall for hours while trying to bind this thing. I can't believe all I had to do was type "save"! Thanks a bunch, man!

[@TweetFPV]

I'm glad it helped you! If I have a dollar for everyone who's had this issue..... 😂

[@skybork5555]

I'm from Russia.Thank you so much for the video!!! I tried everything, tried to connect the drone for three days, this video is the only correct solution to the problem with connecting the drone!!

[@TweetFPV]

I'm glad this video helped you out.

[@RYVENANT]

You're not kidding with the "this is the part people always forget". I ALWAYS forget that part. Thanks for the help man. Great video, straight to the point.

[@jimcrouch683]

Thank you again for your help! I was going back and forth with HappyModel and together we got the Mobula7 to bind with the Taranis QX7 ACCESS radio. Here are the steps I did: FrSky QX7 Radio: ISRM 2.1.6, BetaFlight: version 4.3.0, BetaFlight: Receiver Mode: SPI Rx, BetaFlight: SPI Bus Receiver Provider: FRSKY_X_V2, BetaFlight: CLI Line: Bind_RX (Lights next to USB indicated binding mode), FrSky QX7 Radio: bind in ACCST D16 for 6-8 seconds (Lights nest ro USB indicated a bind!), BetaFlight: CLI Line: Save, Disconnect USB Power to Mobula7 (FrSky QX7 Radio reported "Lost signal"), FrSky QX7 Radio: Bind off, Reconnected USB, BetaFlight shows bound via Receiver tab corresponds with stick movement on FrSky QX7 Radio!

[@TweetFPV]

Awesome! I'm glad bf finally has incorporated a accst v2 code into the spi based boards.

[@damianus]

That "save" saved my life!

[@TweetFPV]

If I had a dollar for everyone who has said that 😂 glad it got you going!

[@PawkBus]

Great Video. No one else out of all the videos I have watched mentioned typing save. thanks for the help !

[@FlyHighWisconsin]

this is the second time I've had to watch this video. First was for the TH2, this time was the TH2 freestyle because I forgot! Thank you so much again!!

[@TweetFPV]

awesome!

[@bryanbaker5603]

OMG!!! You don't know how many videos I went through to get my Taranis x9d+ SE 2019 to work with the TinyHawk2 and yours was it. Even bought an external XJT module for it. After upgrading the receiver firmware and following your procedure, I finally got it to work. Can't speak to the range question yet but Thank you!

[@TweetFPV]

Awesome I'm glad to help. For some reason my videos dont get discovered easily.

[@papapun]

Posting this for anyone looking. This worked for me using an X-lite s radio and the betafpv beta85 pro. thank you for making this video.

[@TweetFPV]

thanks for watching!

[@Kaizer14th]

your comment about "save" - saved my day(night)

[@TweetFPV]

Glad i was able to help you out!

[@yonimushermusic]

hey dude just wanna say thanks, I was very frustrated and this really calmed my nerves

[@TweetFPV]

Glad I could help

[@adirondaxrex]

You are my hero. I've been going in circles for days because I thought the binding problem was with the cheapo FC, not he expensive receiver I had just gone to lengths to update.

[@dmitrym2922]

That "save" command got me. Thanks!

[@NikolasHarcsztark]

Thank you soooo much! Using a Betafpv 65s and got confused with all this binding stuff... Youve truely saved me ;D

[@TweetFPV]

Glad I could help!

[@user-ju4kp4jr1q]

Man, thank you so much :) this "save" thing really helped!

[@TweetFPV]

No, problem!

[@TheAcydbuzz]

For real! How has no other documentation I read mentioned save after the bind command!? I'm going to drop a couple geedubs on your patreon right now.

[@TweetFPV]

I'm always happy to help. Thank you for your support!

[@justinfoster6135]

no way!!! your a life saver!!!!! i cant believe this worked, btw i didnt update the opentx and am still on 2.3.0

[@TweetFPV]

Awesome!

[@MrLOWBOTTOMS]

Thank u so much! Went through hundreds of videos and yours helped! All the other videos the whoops had buttons to bind.

[@TweetFPV]

Glad it helped! all of these whoop do have a bind button but i believe that the CLI method is 100% reliable. The button has a lot of guess work haha

[@bighandswork2]

Thank you! U saved me from returning my FC :)

[@TweetFPV]

I'm glad it helped you!

[@kkaminski]

After watching 1st minute I thought You will going to tell us a way to use D8 natively on X9 lite. I was about to lose my hair since I have ordered XJT Lite for myself 2 days ago. Anyway, good video just 1 tip for others - if You are flying in EU on LBT stuff make sure you choose FRSKY_X_LBT as SPI Bus Receiver provider in Betaflight.

[@TweetFPV]

Oh yea good point. I always forget about the lbt stuff.

[@stevendroogmans1941]

Thanks! That solved the problem for me

[@zuqafpv]

i selected frsky x lbt version on my th2 indoor and bind with my taranis xd9+ 2019 easily with old internal rf firmware but i have a rxloss issue when im flying like 1min and rxloss randomly how can i solve this problem

[@romanstepanenko-0119]

@@zuqafpv Yeah. I have the same. For me helps to change "PID loop frecuency" (In System configuration) to 2 kHz or below. Looks like the CPU on whoop overloaded at 8 kHz. But Gyro update freq still 8 kHz. And it's just fine for me.

[@andyross1454]

This video just helped me finally bind my mob6 hd to my xlite (EU) after hours of searching. Had to add a lua script too to get mine working. Thanks so much for the help. Subscribed!

[@TweetFPV]

I'm glad this helped you out!

[@L3GENDZLuLKeK]

Got it bound thank you sir. Screw the bind button. Ty

[@TweetFPV]

Yea bind button is so last year 😂

[@dronecrashtv8314]

This is the video that made stupid fpv goggle guy possible. Thank you for all the insight on this fresh world. JB for Prez!

[@TweetFPV]

I'm happy you enjoyed it!

[@paulgiusti6779]

As usual great video and thank you! Unfortunately, the XJT Lite modules on the shelf's now will not work for D8 mode. I asked Wayne at Aloft Hobbies in Novato, CA what was up as I could not bind any of my D8 receivers. He has a direct pipeline to FrSky and told me while D8 shows as an option in the XJT lite bind choices, it is not active due to D8 being illegal in Europe. One of our Multi GP club members has the iRange lite multi-module and that does work for D8 but costs over 1.5 times more than the XJT Lite and as far a I can tell only Bangood carries it so good luck getting one of those out of China right now! Sigh, I agree with you I love-love-love my X9 Lite and hate I have to take my big clunky Q7S to whoop races!

[@jackjohnson4524]

Ive been strugging since my Taranis & Beta85 were delivered hours ago. This the video I was looking for.

[@TweetFPV]

I'm glad that this helped!

[@jackjohnson4524]

TweetFPV got me in the air this past weekend. First flights with the QX7, and 5 lipo packs didn’t feel like enough 😂

[@HDBoy]

Thanks, works good on my BetaFPV Beta85 Pro 2 Brushless Whoop 2S Quadcopter (Frsky): Firmware: BTFL 4.2.8 : bind_rx

[@timothysearcy697]

sweet. thats a confirmation enough for me. are you using acct 2.0 or 1.1.3?

[@HDBoy]

@@timothysearcy697 I didn't upgrade my QX7 to ACCST 2.0, because if I'm right it will no longer work with receivers with original ACCST protocol, so the firmware version is: 2.3.9 , internal RF XJT D8 .Hope it helps.

[@gautamsenthilkumar823]

Thanks a lot for the video I was able to bind it to d8 easily using xjt lite module.

[@lionelc9819]

You save my life with the command 'save', thank you very much!!!!!!!!!!! :) My case Tinyhawk 2 with x9d+se in eu_lbt

[@TweetFPV]

Glad i could help!

[@Sensei_Ishikawa]

how you did that ? i struggle alot ...tried so many things . i have same setup th2 with x9d+se eu_lbt. do i have change the spi to frsky_x_lbt or not ?

[@TweetFPV]

If you have a lbt radio then you need to use frsky_x_lbt but you can not be on isrm v2.x you need to be on v1.1.3

[@Sensei_Ishikawa]

@@TweetFPV it finally worked. i guess i hadn't waited long enough after the bind_rx command. thanks for the help

[@TweetFPV]

No problem! If you need any more help feel free to ask over on my discord server. You can find the link on my website www.tweetfpv.com

[@djroman75]

Great video! If I had been able to see this video a few weeks ago. I would have saved soo many hours of research. 👍🏼

[@vedder30]

This worked great and relatively painless for binding a Taranis X9D SE 2019 to a BetaFPV Meteor 65 - Great Video!

[@TweetFPV]

Glad it helped!

[@papierkorbknackwurst]

I tie exactly the same things as you do. Which software versions do you have on your remote control and your meteor 65

[@TweetFPV]

Opentx v2.3.11 isrm V 1.1.3 betaflight 4.2.0

[@papierkorbknackwurst]

@@TweetFPV betaflight 2.4 !? You mean 4.2

[@TweetFPV]

Yes

[@Blakeaholics]

O M F G I wasted an entire day missing typing save. Thank you thank you thank you thank you. I apparently got my shit setup in minutes and yet wasted my day lol.

[@deanelizardo993]

Absolutely fixed my binding issue. Thanks!

[@TweetFPV]

Glad it helped!

[@kennyadamik9801]

Thank you...order the mode but been dieing to use my radio

[@timofunk5374]

You made my day! Thanks a lot, take care!

[@kennyadamik9801]

So I did this and it worked, but I got the xjt mod and it makes a huge difference

[@TweetFPV]

the the external XJT is the way to go for sure!

[@zuqafpv]

i selected frsky x lbt version on my th2 indoor and bind with my taranis xd9+ 2019 easily with old internal rf firmware but i have a rxloss issue when im flying like 1min and rxloss randomly how can i solve this problem guys

[@RYVENANT]

Do you have any idea what would cause the Taranis to freak out? I got mine binded but after setting up the switches, it won't arm. The taranis is also constantly saying "Telemetry Lost" or "Telemetry Recovered" or "RF Signal Critical" and nothing I'm doing is getting the drone moving. Tried binding with both Telemetry on and off in the model settings, tried switching the Rx back to FRSKY_D (which led to it not binding at all) and I'm at a loss. Any clue what could be happening here man?

[@jimcrouch683]

Still no joy. Set the ISRM to 1.1.3 and followed your directions to a T. I have the FrSky QX7 ACCESS and the Mobula7. Been beating my head on this for a week! I have been going back and forth with HappyModel as well, and still no joy.

[@theronin48]

Cli binding has worked great for some whoops but still can't get it to bind with newbeedrone FCs.

[@TweetFPV]

Idk if newbeedrone fc recievers are on a spi bus

[@BrandonBeans]

Those boards only bind by single pressing the boot/bind button on them.

[@hotchicken2852]

You sir just got a like and a sub. Thanks for your help ! He really means it when it’s says SAVE !

[@TweetFPV]

Glad it helped

[@787sever]

So I got my 1s Mobula 7 bound now it was the new firmware not playing nice. But now the damn thing has no throttle response on the throttle stick everything including thr responds in bf correctly but when armed there is zero motor spin up except for pitch and roll if i give it right stick input i get the correct yaw/roll motor spin but no main power on thr wtf is wrong ?

[@xmonstar420x]

thank you for the clear instructions.. im having trouble still with a quad running xm+ that i bought second hand and im unsure if its accst 1 or 2 and cant get it to bind.. would love some help and willing to compensate for your time..

[@xmonstar420x]

BTW - this did work binding to my TH freestyle II !!!

[@TweetFPV]

I can certainly help you out. If your radio currently works with your th2 then your radio has access v1 fw on it. You will need to flash accst 1.x fw to your xm+ or upgrade the fw on your radio.. The down side to upgrading your radio is it will then be incompatible with your th2.

[@xmonstar420x]

@@TweetFPV so I'm new to the hobby and that's the receiver I was told I had and I couldn't find a matching picture on the internet and come to find out it's not a XM plus even though I had bought a new one to install and replace in case it was broken. It's actually an rsxr .. one of the wires was broken on it and I tried to resecure it to the plastic clip or whatever that plugs onto the receiver but even though it's getting powered I don't think that s bus wire is connected well because I can't get it into s bus mode in the blue light will not flash it all no matter what I try so that's my theory on it and now I have the choice between messing with the rxsr or just replacing it with the new XM Plus. Sorry for the novel however just trying to explain in detail to avoid any confusion and asking what would you do if you were me. Thank you so much

[@grzbiet]

helped a lot, thank you

[@emrahksk83]

Hi is it possible to add external sbus receiver (radiolink) on fc that have internal spi frsky receiver?. Will it work? I want buy uz65 but this have not "no receiver" version or "radiolink receiver" version.

[@TweetFPV]

Typically you can. Most spi boards do have at least 1 uart broken out on the board but the soldering is very difficult as the pads are very small.

[@emrahksk83]

@@TweetFPV i will try. Thank you

[@Ghigster2]

Have you had any problems with arming if you use trim? On my x-lite-pro, if i trim it, then dis-arm, it wont arm again until I center the trims out. Any help would be greatly appreciated.

[@dannygayhart1614]

I just bought a new Taranis X Lite Pro and a TinyHawk S. I also have a new R_SRX receiver and a XSR_Sim modular , none will bind! I have Open TX 2.3.9 in TX and use Beta flight 10.7.0. Been working for hours with no luck, Got any ideas.

[@TweetFPV]

You need to make sure your bootloader is on the same version so 2. 3.9. Did you flash new fw to your internal module (isrm)?

[@technicallyjake]

mine only connects if on my transmitter i turn race mode on then off and then i try and bind

[@thomaskrogh2036]

Hi there, Great video and explanation. I have tried everything and I can't get my Tinyhawk S to bind with my Taranis X9 lite. I followed all the steps (also in your other video on how to update firmware). I did it all except one thing. I updated to the 2.3.7 opentx firmware instead of 2.3.5 and I updated the bootloader to 2.3.7. Can that be what courses me the troubles? Or should it work with that firmware and bootloader as well? All the best from Denmark

[@TweetFPV]

the boot loader not being updated can cause issues with binding. also the ISRM FW needs to be on v1.1.3 the V2.x WILL NOT work with the spi boards on D16

[@thomaskrogh2036]

@@TweetFPV alright thanks. I'll try to upload the bootloader and the ISRM to the exact same version as you have in the video. I just couldn't seem to find it.

[@stephenpolkowski8409]

@@TweetFPV Thank you so much!!!!!!! I finally got my FrSky X-Lite S to connect to my Tinyhawk S in D16 mode. I upgraded to OpenTX 2.3.7. I down graded my ISRM FW to v1.1.3 and it starts working! Cheers.

[@MrSabram07]

Thank you for this, I am new and this totally confused me

[@TweetFPV]

Glad it was helpful!

[@georgecollins3794]

I cannot bind my jumper t18 to my iflight 65s spi d16 drone. Please help I have tried every frsky channel on my radio and tried to do it on betaflight and got error messages. I have a tiny hawk 2 that works fine with frsky d8

[@TweetFPV]

In betaflight what reciever protocol are you set to?

[@byahenilloydie9359]

How about on x18 ethos cant make it to bind

[@E4zlLP]

Thank you so much! worked out+

[@TweetFPV]

Awesome!

[@JULIANysuHOHNER]

With d16 on my taranis xlite9 i wont have issues like range or something else?i want to know if is worth keeping this radio to fly tiny whoops like tiny hawk or others that have d8?

[@TweetFPV]

Most likely you will experience poor range on d16 mode when bound to a spi reciever. A external mpm is a good idea for d8 mode.

[@uniquewebshop7084]

Can you please explain me how to bind a moblite 7 with a taranis x9 lite eu lbt please?

[@TweetFPV]

Ok. I'm working on that video now..

[@TweetFPV]

But basically same process but you select frsky_x_lbt in betaflight. If you don't see that then you'll need to update bf. Be sure to back up your betaflight settings.

[@TweetFPV]

I really hope you already got it bound but if not here you go! kzbin.info/www/bejne/eYCvZqN_m81ojtE

[@hardtmuthsv]

I have bata65s copter and taranis x9 lite. FW 2.3.12 and I can't bind copter to taranis x9 lite. is it possible that problem with FW 2.3.12?

[@TweetFPV]

No, its not a problem with openTX V 2.3 12. The issue you most likely have is that your internal rf module fw is incorrect. The highest isrm version fw that will work with these spi based receivers is v1. 1.3 it is also region specific. If your radio says isrm version x.x.x EU then you need to change your rx protocol in bf to frsky_x_lbt. If says x.x.x fcc then you need to change it to frsky_x

[@izaya8986]

Thank you for your effort. apparantly it was too much to mention to hit :save: after bind for the other instruction vids. smh

[@TweetFPV]

I have found that other reviewers are taking the easy way out and not talking about how to get these radios to work and are just suggesting buying something else. These are really good radios one you figure out thier quirks.

[@AllenOxendine]

Excuse my ignorance but I’m new to FPV flying. I purchased the Tiny Hawk Freestyle. Didn’t know what kind of transmitter I needed. My second transmitter is the Taranis FrSky x9 Lite. Will this work on the Tiny Hawk?

[@TweetFPV]

It will.

[@AllenOxendine]

@@TweetFPV I've spent so many hours looking for help. I'll give this a try..

[@TweetFPV]

If you have troubles hit me up on discord. I've help more people than I can count with using that radio and Quad combo.

[@AllenOxendine]

@@TweetFPV I'm still looking for your upgrade video..

[@mr.miami.3053]

You are the effing man !!!!

[@TweetFPV]

thanks

[@ryankraft322]

New to all of this and the Taranis Q X7 Access with a tinyhawk 2 has given me a bad introduction. Is there a receiver that works with the tinyhawk 2 without having to do all the mumbo jumbo?

[@TweetFPV]

There is but your best option is to purchase a external multiprotocol module for your radio.

[@ryankraft322]

@@TweetFPV Got it. Thanks.

[@anthonylawell4979]

Hey man I did what you said just getting into this hobby. This video seems a bit dated so maybe the newer firmware doesn't work? Did everything I said and I can't get it to bind :(. I noticed that when I created a new model I didn't get that option to select what kinda model either. Plz help I'll buy u a beer!

[@TweetFPV]

I can certainly help you out. Head over to my discord. Its way easier to troj le shoot that in the KZbin dialogs box. www.tweetfpv.com

[@OLEHFPV]

so I tried this but using emuflight and I did the frsky_bind commant and save and it didnt work

[@TweetFPV]

I haven't tried it on emu. I don't see why it wouldn't work. You are probably missing a step ot don't have one of the setting correct.

[@niioniio]

I'm spending second day to try get the TaranisQ X7 ACCESS working with my tihyhawk2. I use the ACCST D16 mode, the TH and radio are bind together, but in betaFlight and also during flight the RSSI often drops to zero (like every 10s). Any advice here?

[@TweetFPV]

The only recommendation I have for you is to get an external multiprotocol module. These radios and fc do work in d16 mode but they do suffer from terrible range and poor connection quality. Some work well others do not. Sounds like yours is one of the do nots.

[@niioniio]

@@TweetFPV would be also solution to install separate frsky rx into tinyhawk?

[@TweetFPV]

Yea that would work too. But the mpm will do more for you in the long run.

[@oscartothewild]

Hey man great video! I decided to get an XJT module for my QX7 Access to avoid the D16 hussle, but it turns out that my QX7 module bay is way bigger than the x9d and I cannot plug in the XJT. Do you know of any other modules that I cant attach to the QX7? Thanks!!

[@TweetFPV]

The module bay for the qx7 and the x9d are the same. The x9 lite and xlite use the mini Jr bay. If you have the qx7 you need to look for a xjt module like this one www.amainhobbies.com/frsky-xjt-transmitter-module-frk-3030401/p1167046

[@illmilltube]

I'm guessing this doesn't work with the newer firmware update for the radio that's required to use the r9m lite pro module and newer r9 ota receivers. can you confirm which firmware version or release date you have here please?

[@TweetFPV]

I'm using opentx 2.3.9 ISRM FW v 1.1.3 and this will not work with V 2.x FW. Your R9 fw is independent of your internal (ISRM) FW. so you can run older ISRM FW and current R9 FW at the same time.

[@blam3329]

I've been able to bind SPI receivers to the X-Lite pro and X9 Lite for a while now using the frsky_spi_autobind CLI method. We recently got our shipment of Archer RS receivers in from the factory. I was not able to register/bind them at all until I updated to ISRM 2.x, which killed my ability to bind to SPI receivers. Their "technical rep" sent me the link to this video, but it doesn't seem to address that. Is there a workaround for that yet, or will I have to flash the ISRM back and forth?

[@TweetFPV]

Unfortunately You will need to reflash your isrm back and forth. Or purchase a external multiprotocol module or the xjt lite module to use d8.

[@keithcarpenter5254]

Will this work on an eu lbt radio (accst x9d+)? Or do i have to do the firmware update, as I've been told, on discord? This is a whole lot less faffing around than doing that? Tia.

[@TweetFPV]

Same process but you need to select frsky_x_lbt in betaflight

[@TrentTationnaiseXization]

O man thank you!

[@TweetFPV]

Hope it helped.

[@richifpv6908]

Heeeey :) Thanks a lot for your video ! However, impossible to bind my bet65s with my taranis qx7 ACCESS... I flashed the 1.1.3 isrm firmware, I'm in eu, and the spi receiver is set to FRSKY_X_LBT. Also, I'm well on the 2.3.5 version of openTX... Don't understand what is going on. Any help would be welcome :) Cheers !

[@TweetFPV]

Is your radio setup as fcc or lbt in the module version page?

[@richifpv6908]

@@TweetFPV I'm trying to flash the old xjt firmware in FCC but not working... In the module page it says, ISRM-N 1.1.1/1.1.3EU

[@TweetFPV]

Have you tried using frsky_x the non lbt version?

[@TweetFPV]

I haven't dealt too much with the lbt issues.

[@richifpv6908]

@@TweetFPV Yop also tried this one :(

[@jrrmos]

Hi my friend. Do you have the SRM version v.1.1.3 to share.? I have the taranis x9 lite S. Tks

[@TweetFPV]

You can find it at frsky.com under the download section.

[@amgadmohsen5934]

I have followed the same steps, but unfortunately it didn't go through. the qx7 access Tx operating system is up to date 2.3.9 Betaflight version 4.0.0 is uptodate 10.7.0 Configuration is Frsky_x in the CLI: bind_rx_spi, then put the radio on bind mode D16 then hit Save. nothing worked! :( Can you please tell me if there is anything I need to check

[@TweetFPV]

check to see if your bootloader is v 2.3.9 as well.

[@AA-gl1dr]

Thank you so much!

[@cometpowell]

Got it to bind. Now I’m dealing with loss of RX or bad RX, rendering my TH2 useless. Any ideas? Using a taranis x7 with access

[@TweetFPV]

You can try disabling telemetry, or re-binding but this is a side effect of using d16 with these spi boards. Some are great and some are terrible. It's a complete roll of the dice. You unfortunately might just have one of the bad ones. I highly recommend getting an external module for these spi d8 quads or you can add an external rx

[@Toys4boysDrdrone]

hey thanks for you video, i already made the bind with the drone, nut then it happens as if lost signal and comes back after a few seconds. Any idea it might be? Thanks

[@TweetFPV]

Might just have the controller too close to the board. Sometimes they get swamped out.

[@Toys4boysDrdrone]

@@TweetFPV ok thanks, i hate this BetaFPV SPI receivers

[@TweetFPV]

It's all spi frsky clone receivers.

[@goldexpo2219]

THANK YOU!

[@carsonoliphant7985]

Thank you sooooo much!!!!! Liked and subed this was such a huge help finally could bind up to my d16 receiver

[@TweetFPV]

Glad I could help

[@jousiff91]

when I choose SPI RX support and choose FRSKY_X the save and reboot. when i connect again it goes back to the default one! I have beta 85 whoop drone!

[@TweetFPV]

That's really wierd. After you save it goes back to frsky_d?

[@jousiff91]

@@TweetFPV no the default one is: "PWM RX input(one wire per channel)"

[@TweetFPV]

Which version of the beta 85 do you have? Some came with no receiver.

[@jousiff91]

@@TweetFPV frsky fcc xm+. I sure there is one because i am pressing the bind button like all the videos am watching haha. the problem is the red and green lights are just solid when i press the binding button and connect the battery while my transmitter is on binding mode

[@TweetFPV]

@@jousiff91 Something isn't adding up here. If its XM+ then you aren't using an SPI board. which would make sense why it wont save the changes to the protocol like you mentioned before. Is the "bind" button you are pressing on the flight controller or on a separate board? Pictures would really help. Head over to my discord and i can help you better over there. www.tweetfpv.com link to my discord server is there.

[@nickoncomputer9081]

I had the opposite experience with my x lite pro. When I bound my tiny hawks using D16 they had decent range but once I got the xjt external module and bound in d8 they have poor signal even when only a few feet away. Any ideas what might cause that?

[@TweetFPV]

This is odd. I would say you possibly have a faulty module. D8 in my experience is always better than d8 with the spi boards.

[@nickoncomputer9081]

TweetFPV faulty module meaning faulty xjt lite?

[@UrFatUncIe]

damn, unfortunately my emax and x9 lite still won't bind Dx

[@TweetFPV]

Go to www.tweetfpv.com and join my discord. We can help you get it up and going over there.

[@teobass82]

Hi, a non-Frsky module multi-protocol does not work, but a Frsky ACCST module could work on ACCESS radios? I don't understand this strategy...

[@TweetFPV]

Non-frsky mpm does work. The tbs one does not.

[@teobass82]

@@TweetFPV Are you sure? If I take a QX7 ACCESS and put in an ACCST module does it work? For example irangex or Frsky XJT? Now there is firmware 2.x.x, someone has problems

[@TweetFPV]

Yes it works as long as you have updated your opentx os past version 2.3.3

[@TweetFPV]

Take other people problems with a grain of sand 50% of opeple using this stuff have zero idea how it works. Not that frsky makes it easy.

[@teobass82]

@@TweetFPV thank you. Usually the simplest test is to try 😉 Then there is another thing of and I have doubts, if you upgrade a radio to Frsky v2.x.x you get a D16 V2. Does the D8 still work?

[@CarbonGlassMan]

Is access d16 the same as d16? I have the XSR Sim dongle and it's refusing to bind with my x9 lite. I assume that means they're different?

[@TweetFPV]

There is no access d16. Its either access or accst d16. It is possible to bind to your Sim dongle in accst d16 mode but you will need to make sure your internal rf fw is compatible. V1.1.3 on your isrm should be what works.

[@CarbonGlassMan]

@@TweetFPV That's it. Accst d16. I was going off memory on what it was called. I'll have to check the firmware versions. That's probably what the problem is. I seen one guy say "I dint know why you would ever want to flash new firmware to your gongle" then I seen another guy flash new firmware to it and his radio and that made it work. I don't recall if I ever updated the firmware on my x9 lite or not. It's been so long ago now. Thanks for the answer.

[@TweetFPV]

No problem.

[@MrSabram07]

I'm at work so I'll have to double check, but I think my Taranis QX7 will not go into ACCST It will only go into a ACCESS or ACCESS16. Am I remembering correctly, is anybody aware of this?

[@TweetFPV]

you are not remembering correctly. Your new model QX7 will do ACCESS and ACCST D16

[@MrSabram07]

@@TweetFPV That's exactly right and I learned how to update it and now it's working. But I wouldn't have figured that out without your video so thank you

[@hayden_mx8075]

What did you say to type at the end to bind it

[@TweetFPV]

Bind_rx

[@TweetFPV]

But it depends on the version of bf you have on the board.

[@aceqman]

Of course it is FrsSky's fault!!! It used to work so they could enable it if they want. Just sold mine and bought a T16!

[@TheAcydbuzz]

Okay, now I'm having a different problem. After fiddling with a few settings on Beta flight, I decided to reset the settings and just create a new model on my TX. After doing so, Betaflight isn't preloading the range values for the AUX1-3 controls anymore and I'm not fully understanding how it was setting those up to begin with. No matter how I set the ARM and ANGLE, the Mob6 will not arm and I haven't found a way to create a "crash flip" control from scratch. Should I flash the board on the whoop or is there another way? I'm about ready to just throw this damn thing. I'll get more air time out of it that way. LOL j/k

[@TheAcydbuzz]

Also, has anyone tried out the iRangeX module with anything? I've got one on the way in hopes of using the X-lite with my Mini Convergence.

[@TweetFPV]

Did you flash new fw in bf or did you just hit the reset settings button?

[@TheAcydbuzz]

I just hit the reset settings button thinking it would revert back to the setup it initially created the model with.

[@TweetFPV]

Haha yea that's not how it works unfortunately. Did you back up your settings before you did that? Either way the channels are probably not populating because you need to go to the config tab and enable spi based receiver and frsky_x if you were running d16. Unfortunately this will just be the top of the iceberg of issues you might encounter from clearing the settings.

[@TweetFPV]

discord.gg/YrB7BSv hit me up in discord and I can send you a config dump for the mobula 6 to get you back to stock.

[@david20094]

followed the video really easy to follow but unfortunately i still cant get my x9 lite to bind to my mob 6 - should probably mention Europe based have your or anyone here in the comments had similar issues?

[@TweetFPV]

Have you tried using the frsky_x lbt mode in the bf config tab. I have to admit I have no experience trying to get a EU branded radio to work like this.

[@david20094]

@@TweetFPV I was reading the comments and I saw that so I hopped back into betaflight to check I don't actually get that option for some reason this is my first drone so I'm learning as I go, I have a feeling ill end up needing a external module that supports it natively for some reason. If you have any other suggestions I'd appreciate it! :)

[@TweetFPV]

Hmm what version of bf do you have?

[@david20094]

@@TweetFPV can't remember the exact version but the bind command I get with tab is bind_rx so it's 4.1.x

[@Dave-xv8xh]

I have a Taranis Q X7s ACCESS radio and a Tinyhawk Freestyle. After flashing the ISRM module from v2.1.0 to v1.1.3 I managed to the bind the Tinyhawk to the radio in D16 ACCST mode but the signal is so unstable that the quad is impossible to fly. When I power on the radio and the quad the signal remains "stable" for about 5 seconds then it keeps dropping and coming back every 15s or so. The radio keeps saying "Telemetry Lost, Telemetry Recovered, Telemetry Lost, Telemetry Recovered... RF signal critical" etc. I have tried both FCC and EU (LBT) modes but the issue does not disappear. Does anyone know what the reason could be?

[@TweetFPV]

The reason seams to be an issue with the amount of data sent in d16 mode. Some boards are better than others. This is why i don't really recommend using d16 mode with SPI based boards. The XJT module is the only real way to get D8 for these models to work well.

[@Dave-xv8xh]

@@TweetFPV Thanks a lot for taking your time to read comments to reply! I have read somewhere that FrSky has disabled D8 in newer XJT modules, even if it is displayed as "availble" in openTX...

[@TweetFPV]

That is not true. D8 works just fine with the XJT module just not the ISRM on newer ACCESS radios. There is a LOT of incorrect info out there by people who just don't understand how these radios work.

[@Dave-xv8xh]

TweetFPV thank you very much!

[@TweetFPV]

no problem.

[@apextos81]

I had my tinyhawk 2 bound to my taranis Q X7 accst. After installing a long range module on the taranis and doing a firmware update I can no longer bind to my tinyhawk. Even when I turn external module off. Can someone help here??

[@TweetFPV]

You might have accidentally flashed over your internal rf moduel. Go to www.frsky-rc.com/taranis-q-x7-3/ and download the ixjt fw but select the "history" version not v2.1 copy that to you sd card and flash your internal module with that fw.

[@ErichHaubrich]

@@TweetFPV My QX7 will not let me overwrite the existing firmware. "FW update error. Not responding"

[@TweetFPV]

Which fw did you have and which are you trying to write?

[@uwtab6898]

I tried over 11 video's to bind the Frsky x-lite with the tinyhawk x, not 1 time it binded to the drone! ... seriously frustrating. Following every instruction exactly like instructed.... :(

[@TweetFPV]

sorry to hear that. This does work. if you would like me to walk you though the process head over to my discord server and i can help you out. discord.gg/YrB7BSv

[@uwtab6898]

@@TweetFPV Thank you for the offer! I managed to bind them. Not sure how but eventually changing back from frsky_d to x did the trick, after few attemps of firmware upgrades etc.. Now so happy practicing :D

[@TweetFPV]

Excellent, I'm always here if you need some help.

[@860studio]

How can I get to that version page on a Taranis x9 lite? I can’t seem to figure out what firmware I’m running

[@TweetFPV]

Hold the menu button to get into the system menu then scroll till you find it.

[@860studio]

@@TweetFPV Perfect. If I upgrade to Open TX 2.3.7 will it connect to my Mobula6?

[@TweetFPV]

Possibly.

[@gautamsenthilkumar823]

I got a betafpv f3 v1.1 board which has frsky rx via sbus protocol how to bind to it using frsky x9 lite. I have both d8 and d16 using xjt lite module.. new to this hobby kindly help me to bind to the brushed fc.

[@TweetFPV]

It's the same process but you can't use the cli command for binding you'll need to be in d8 mode on the xjt lite module

[@gautamsenthilkumar823]

@@TweetFPV yes I tried using d8 but still can't bind to fc red light blinking no solid light

[@TweetFPV]

Hmm that should work. And be fairly straight forward. Have you been able to connect to any other quads with the xjt lite module?

[@TweetFPV]

Also does the led on the back of then xjt lite come when trying to bind?

[@gautamsenthilkumar823]

@@TweetFPV yes

[@paulonoleto1853]

I did exactly everything you did and it didn't work 😔 X9 lite s Mobula 7 (crazybee f4 v2)

[@TweetFPV]

you had to have missed something or some setting didn't take. I can help you out over on my discord server. discord.gg/b2nUTux

[@jlmarco7552]

doesnt work with ISRM-N 1.1.1/2.1.0 :-/

[@TweetFPV]

Correct. V 1.1.3 or older.

[@KassieCBR600RR]

God safer !!!!

[@davidmugami6150]

Will this work on 2.3.12

[@TweetFPV]

Yes

[@davidmugami6150]

@@TweetFPV I'm having issues get it to work on my tinyhawk freestyle 2 I have a frsky x9 li I believe

[@TweetFPV]

It is doable for sure. You just need to make sure all your fws are crooect and bf is setup properly

[@davidmugami6150]

@@TweetFPV what you mean by fws please and I believe I have everything on bf setup right I'm on frsky x for the EU as I'm in the UK I have been trying all day with different settings and it's not binding at all

[@TweetFPV]

Fws = firmwares You need to set in bf to frsky_x_lbt since you are in the eu

[@papierkorbknackwurst]

When enter save, my drone reboot

[@TweetFPV]

Yep that's how it works.

[@papierkorbknackwurst]

@@TweetFPVohh yes have just seen it starts again with you. But then it is not connected with me

[@TweetFPV]

To help you I need more info. 1. what radio are you using? 2. What version of opentx? 3. What ISRM firmware version? 4. Is your radio FCC or EU? 5. What is your bootloader version?

[@papierkorbknackwurst]

ok i have now managed to bind my meteor 65 with the taranis x9d plus se 2019. everything actually works, only when the copter is armed the message comes in osd: rcsmoothing, and I can't start

[@TweetFPV]

That's an odd failure. Have you made any changes in betaflight from the stock firmware setup? What is your cpu usage when you are connected to betaflight?

[@tcturtle89]

Ugh my won’t even connect 😒

[@TweetFPV]

Your doing it wrong then or you don't have your operating system and bootloader updated. There is a small gotya with the rf fw. You need to be on isrm 1.1.3. You can no be on 2.0 or newer.

[@syndicategraphics6140]

Money