How to Build a Wood Slat Wall - Step by Step | The Lake House Project Ep 20

  Рет қаралды 1,848,330

Golden Key Design

Golden Key Design

Күн бұрын

Пікірлер: 735
@priscilajaelwebb1664
@priscilajaelwebb1664 8 ай бұрын
Going to do this for the reception of our language school in Brazil. Thank you. I love this!!!
@GoldenKeyDesign
@GoldenKeyDesign 8 ай бұрын
Wonderful!
@carolkhumalo8222
@carolkhumalo8222 11 ай бұрын
I love the box around the switch box idea...brilliant and looks slick.
@GoldenKeyDesign
@GoldenKeyDesign 11 ай бұрын
Thanks!!
@eq2046
@eq2046 2 жыл бұрын
Thanks for sharing. Putting an MDF under the slats is a brilliant idea that makes nailing much easier.
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you! Yes, it allowed me to nail the boards wherever without having to worry about hitting a stud and it paints very well too!
@MrSteeDoo
@MrSteeDoo 2 жыл бұрын
at $53 a sheet it is too painful for me to purchase 3/4" mdf
@DarrenMossAU
@DarrenMossAU 4 ай бұрын
Great job, well measured and executed. I like the timber trim around the outlet and light switches. Well done!
@GoldenKeyDesign
@GoldenKeyDesign 4 ай бұрын
Thank you very much!
@beaverlakepumpdauphin2169
@beaverlakepumpdauphin2169 5 ай бұрын
Great video. All the important information in a quick, concise matter. Walk looks fantastic.
@carloantoniomartinelli5418
@carloantoniomartinelli5418 2 жыл бұрын
Congratulations ! You have done a FINE JOB ! And proven once again the adage " Measure twice ( or more if you need ) and cut once. Above all I like very much the way you THINK first. The results are on yourn side. BRAVO.
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you for the kind words! Really appreciate the support!
@jim9520
@jim9520 8 ай бұрын
Thank you for this video. Very, very nice. Beatiful.
@GoldenKeyDesign
@GoldenKeyDesign 8 ай бұрын
Thank you very much!
@gordthor5351
@gordthor5351 Жыл бұрын
A tip so you are far less likely to have brad nails blowout, is to always hold your nailer perpendicular to the length of the board. In other words, the chisel tip of brad nails will veer to either side of the chisel tip, rather than up and down (due to following the grain of the wood). That is why you want to hold your brad nailer horizontal when nailing vertical boards together. It's better to have the nail veer off on the 8' length of the board, rather than on the 3/4" width of the board.
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Thanks for the tip!
@missEshoe
@missEshoe 2 жыл бұрын
Rewatching this video over and over again. Going to try this out in my new condo-thank you for this instructional video!!
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Haha, that’s awesome! I’m glad you enjoyed the video are able to use it as a guide! Good luck with the project and let me know how it goes!
@ΙΛΙΑΔΑΓΑΛΑΝΟΥΛΗ
@ΙΛΙΑΔΑΓΑΛΑΝΟΥΛΗ 8 ай бұрын
Great job well done it looks professional!!! Enjoy
@GoldenKeyDesign
@GoldenKeyDesign 8 ай бұрын
Thank you!
@Baudesign
@Baudesign Жыл бұрын
Very nice result. Did I notice that at 11:10 you used 18 ga nails? In hard wood, doesn't it tend to bend or fail? Thanks.
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Thank you! I was actually using a pin nailer which uses 23 gauges nails. The nails are so thin that they go into hardwood with no problems
@MH-hi6ug
@MH-hi6ug Ай бұрын
Love your videos! I liked the white light switches better but you do you! 🙏
@chrisfrancis8446
@chrisfrancis8446 2 жыл бұрын
Sweet, this is a great example of we Im wanting to do in my place. thanks
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Perfect! I’m glad you enjoyed it and found it helpful 😁 thanks for watching!
@thearchibaldtuttle
@thearchibaldtuttle 2 жыл бұрын
The slat wall looks nice and the house is even noicer!!
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you, really appreciate it!
@cynthianorwood6333
@cynthianorwood6333 2 жыл бұрын
Awesome Job.. have you taught about making the light covers and outlets covers black
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you! I mentioned at the end of the video that I planned to swap them out for black and I already posted the video about it! They are from Buster+Punch
@MAD42
@MAD42 2 жыл бұрын
good job, dude. thank you for sharing.
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you!
@bexaminer1
@bexaminer1 8 ай бұрын
Nice looking accent wall. I'm going to do the same thing on a wall I have. I know you used a but joint on the two boxes you made for the outlet and light switch. I wondered if you didn't consider doing 45 degree cuts on those. That's probably a little over the top, but I wondered.
@shannonakey8436
@shannonakey8436 9 ай бұрын
Thank you for this video we be using this in our motel renovation.
@JosephVoeller
@JosephVoeller Жыл бұрын
Project look great! Just confirmed you used 1.5 in wide boards with 1.5 in spaces?
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Thank you! And yes, that’s correct 😁
@rick-val22
@rick-val22 6 ай бұрын
The surrounds on the light switches and outlet look really good
@bojanbokur2345
@bojanbokur2345 Жыл бұрын
When you used the router 11:45, how did you get up all the way to the ceiling without the router base getting in the way?
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Good question! I used my orbital sander to finish it off but you could also use a chisel too 😁
@noahcohen6426
@noahcohen6426 Жыл бұрын
Great work man. Love the attention to detail. That nail popping out made me a little sad for you haha! Top job
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Thank you so much! I was really frustrated too, but all turned out okay
@garrettslight3664
@garrettslight3664 Жыл бұрын
Loved the project. One question I had, what’s the purpose of the mdf wall? Could you have nailed/glued it directly to the sheet rock? I realize it might ruin that wall if you had to change it up, but just curious
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Thanks! As you saw in the beginning of the video, the drywall was torn up and it would be a lot of work to patch it up. So the MDF covers all that up and is a nice paint surface. It also allows the slats to be nailed anywhere and have a strong connection to the wall
@orenbaranes457
@orenbaranes457 2 жыл бұрын
its look great. To fix the wood slat to the wall you used nails. How did you hide the nails? What nails did you use?
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you! I used pin nails which are 23 gauge. They are so small that they are pretty much invisible unless you stare at the wall from a few inches away and even then its hard to find them. You can still use wood filler on all holes if you'd like. If you use brad nails which are 18 gauge, you definitely need wood filler as the holes will be quite large. Hope that helps!
@TheMusic4lifetime
@TheMusic4lifetime 2 жыл бұрын
Great design. Why did you attach the MDF board to the ball and why didn't you nail the wood slats directly to the wall without the MDFs. What is the advantage..
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thanks! The advantage is that you can nail the slats anywhere and have strong holding power with the nail. If you just nail into drywall without hitting a stud the slat is not secured as well
@timogronroos4642
@timogronroos4642 2 жыл бұрын
Looks great! One small thing could be to leave just a small gap between the slats and the floor to have a moisture barrier between them.
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you! And that’s a good thought, thanks for the tip
@bob1705
@bob1705 2 жыл бұрын
Thank you for this video. As an avid DIY'er, you filled in a lot of the how-to gaps for me. I'm actually doing this in a 70's era sunken living room where one wall is 9' and the other is 8' on an angle to the adjacent 9' wall. Should look pretty cool when I'm done!
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you, I really appreciate it! I’m glad you found the video helpful and good luck with your project!
@JonesersRX7
@JonesersRX7 2 жыл бұрын
Get some Lutron Claro satin black outlets and screwless outlet/switchplate covers. Will get rid of the eyesore of the white. Looks really good, nice work.
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
We ended up going with Buster and Punch black and brass plates! I posted a video on it already and you can see it in this videos thumbnail
@GabeSchultz1
@GabeSchultz1 2 жыл бұрын
Brilliant to add that detail around the outlets!
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Agreed! Really happy with the way it turned out!
@rwhite9994
@rwhite9994 2 жыл бұрын
Here is a tip. Cut out a jig block for your spacing, but make it long, 2/3, and give it feet. That way you can lean it against the wall. Then, walk away, put it next to your last stile, place the jig, nail off the next stile, place the jig and walk away. That way you do not have to pick up 3 little blocks off the floor or out of your pocket all the time.
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Good idea, appreciate the tip!
@alitsah
@alitsah Жыл бұрын
Did you use the little plastic electrical spacers behind the wall plate and switch or how did you bring the outlet that far out with the wood?
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
You can use those, but I added a box extender which achieves the same purpose
@MaraxYTube
@MaraxYTube 2 жыл бұрын
Just a tip for caulking. Put some soap and water in spray bottle. after you put caulk spray it and it goes off smooth with no sticking :)
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Great tip, but that’s more helpful for silicone caulk. This caulk was acrylic or water-based so a damp finger does the trick!
@NBcal
@NBcal 18 күн бұрын
Amazing vid! Your planning and design ideas are impeccable. What kind of varnish did you use?
@KiNgDaNcEr
@KiNgDaNcEr 10 ай бұрын
Amazing! Such an inspiration. What shade of danish oil is that? Its absolutely perfect!
@tuckerleary
@tuckerleary 2 жыл бұрын
this came out great, really a joy to watch and happy to hear you'd be switching the outlet and switch plates out because that was the only thing I thought looked off. Taking notes from this one, nice build!
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you, I really appreciate it! I posted a video on the new switches too if you want to check it out!
@FRSP53
@FRSP53 Жыл бұрын
Legrand.....;) @@GoldenKeyDesign
@SENTIENT.7
@SENTIENT.7 2 жыл бұрын
what color black paint did you use? Love it
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
We used Limousine Leather by Behr which is the same color as Tricorn Black by Sherwin Williams
@twinenk15
@twinenk15 2 жыл бұрын
Flat or satin?
@ferdinand59
@ferdinand59 9 ай бұрын
Very nice project. Was it 1.5” slats and 1.5” spacing in between?
@GoldenKeyDesign
@GoldenKeyDesign 9 ай бұрын
Thanks! And yes, that’s correct
@Saywhatohno
@Saywhatohno 6 ай бұрын
Amazing video!!! Do you think 1x2 framing lumber would work for slat wall
@GoldenKeyDesign
@GoldenKeyDesign 6 ай бұрын
Thanks! Yes, it would! You just have to make sure the lumber is nice and straight
@Saywhatohno
@Saywhatohno 6 ай бұрын
@@GoldenKeyDesign oh so I need a planar I guess. I saw you guys using it too
@GoldenKeyDesign
@GoldenKeyDesign 6 ай бұрын
@@Saywhatohno No, you don't need a planer. We didn't use one in this project - just a table saw. The 1x2s are already the correct size, but in order for the wall to look good, you need them to be straight rather than warped or bowed
@Saywhatohno
@Saywhatohno 6 ай бұрын
@@GoldenKeyDesign oh so you just straightened it on the go? Because I thought planar can one side straightened
@IAmZen_007
@IAmZen_007 2 жыл бұрын
Very nice!! Love it! Grts from 🇧🇪 Belgium
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you so much!
@rojaspedro7560
@rojaspedro7560 2 жыл бұрын
This is beutiful work. I would love to replicate this. One question I have is, why use the MDF and not apply the slats direclty to wall after it has been plastered and painted black?
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you! As I mentioned in the video, it allows you to nail the slats anywhere on the wall and get a solid hold with the nail. If you just go into plaster, the nail doesn’t have that much holding power. I also mentioned that it was easier to cover the damaged drywall in my case rather than spend the time to patch it. Hope that helps!
@carissadonato531
@carissadonato531 2 жыл бұрын
It gives so much character . Good job
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you! Agreed on the character 😁
@TheBandoury
@TheBandoury 2 жыл бұрын
Perfection! I like the light switch boxes too
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you! I really love how it turned out too!
@NathanBudd
@NathanBudd 2 жыл бұрын
This is great! Very inspiring! One thing I don't understand or I missed you explain... why did the MDF panels not sit flush (gap at the top but not the bottom) but the slats of wood all seemed to meet vertically?
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you! The ceiling was not parallel with the floor causing the gaps at the top of the MDF. I then filled the gaps with caulk. It is not as noticeable with the slats since I cut each of them to fit flush with the ceiling (each is a slightly different length). Hope that helps!
@linnsoltwedel
@linnsoltwedel Жыл бұрын
I think it looks awesome! :D I am very exited to to something like that, its very popular these days.
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Thank you!
@linnsoltwedel
@linnsoltwedel Жыл бұрын
@@GoldenKeyDesign I just channel and I love it!
@ljensen9364
@ljensen9364 29 күн бұрын
Beautiful work!
@aub8670
@aub8670 2 жыл бұрын
Why did you leave a gap between the mdf boards? Was it to allow for expansion?
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
No, it was because the floor was unlevel. It is an older house so things are not square haha
@KingFox76
@KingFox76 Жыл бұрын
The wall looks great and you did a great job on the video, I appreciate that. What type of shoes are you wearing?
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Thank you so much!! I’m just wearing new balances. Nothing special - bought them about 5 years ago
@BaoNguyen-so2rv
@BaoNguyen-so2rv 2 жыл бұрын
Looks fantastic! If you're willing, are you able to share the total time and or material cost of this project? Wife is asking for something like this right now.. ;)
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you! Time depends a lot on if you need to mill your boards. Assuming the boards are already milled, it will take about 2 days (16 hours) to install. Cost also depends on lumber prices and species of wood. Pine might be $150ish and oak will be $750ish. Hope that helps!
@BaoNguyen-so2rv
@BaoNguyen-so2rv 2 жыл бұрын
@@GoldenKeyDesign this is perfect. Thank you so much and again this was an amazing project
@aranck84
@aranck84 2 ай бұрын
This looks great! Nice work!
@GoldenKeyDesign
@GoldenKeyDesign 2 ай бұрын
Thanks!
@blairwhite3973
@blairwhite3973 2 жыл бұрын
If using oak for the slats it is best to use stainless steel nails for attaching them to the MDF. The reason is that the tannin in the oak can react with the iron in the nail and cause black streaks on the wood. The more moisture there is around, the more chance of staining (especially if you’re doing this on an external wall).
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Great tip! This particular wall is inside and does not get much moisture so I haven't has any black streaks and it's been about a year
@destroy43
@destroy43 2 жыл бұрын
Just stumbled onto your video and loving this! Gotta hook a shopvac up to that saw, I think mine hooks right up to it with no adapter even.
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thanks! And yes, dust collection is on my to do list. It’s just a very long list haha
@duanebock840
@duanebock840 Жыл бұрын
My favorite video so far, love the look of this
@kawukiashiraf8756
@kawukiashiraf8756 2 жыл бұрын
Perfection in spacing, but brife me how you calculated that spacing am stuck somewhere
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
There are a variety of ways to do it. I measured the whole wall length, then subtracted out my two end pieces on either side, then divided the remaining distance by the width of my slat/spacing to see how many would fit. Hope that helps!
@kawukiashiraf8756
@kawukiashiraf8756 2 жыл бұрын
@@GoldenKeyDesign got it thanks
@danc2779
@danc2779 2 жыл бұрын
Excellent content and presentation. I hope that your channel will take off 🙂
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you, really appreciate it!
@timmytwister6397
@timmytwister6397 2 жыл бұрын
Spectacular work! Love that you used oak not plywood. The danish oil against black is also a great choice.
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you! Agreed on the oak, danish oil, black combo!
@WGQZ
@WGQZ 8 ай бұрын
I also want to make this wall panel,Really a treasure blogger
@GoldenKeyDesign
@GoldenKeyDesign 8 ай бұрын
Go for it!
@howardsportugal
@howardsportugal 2 жыл бұрын
I so wish I hadn't used that track lolz - great vid!
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thanks!
@Weekbrownies
@Weekbrownies 2 жыл бұрын
looks good, how is it with dust collection?
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you! Do you mean in terms of cleaning the floor? It's not bad and does not collect much dust and it is easy enough to sweep between the slats. But if that is a concern, you can add a baseboard along the bottom for a seamless transition to the floor
@dafecki
@dafecki 11 ай бұрын
Looks great. Is that natural color of danish oil?
@GoldenKeyDesign
@GoldenKeyDesign 11 ай бұрын
Thanks! And yes, natural danish oil 😁
@gerardfenn3988
@gerardfenn3988 2 жыл бұрын
Clean looking Job. Well Done
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you, appreciate it!
@michaelambrose
@michaelambrose 2 жыл бұрын
Nice work!!! Would you mind sharing the total cost of the project?
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you! Everything besides the slats only cost about $50. The oak slats we used added up to about $700 but you can use pine and buy them for closer to $150
@DuncanBuilds
@DuncanBuilds 2 жыл бұрын
love the detail around the electrical plates. that turned out great. whole thing looks awesome.
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you, really appreciate it!
@alexandrugeorge1573
@alexandrugeorge1573 Жыл бұрын
For the extruded switches solution, isn’t there a fire risk with the wood being near the wires?
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
You can add a box extender to negate any fire risk
@farazahmedCH
@farazahmedCH Жыл бұрын
beautifully done
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Thank you! Appreciate it!
@williamweatherall8333
@williamweatherall8333 2 жыл бұрын
That was clever using the mdf panels behind them. This helped me figure out how to do this for myself.
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thanks you! And perfect - glad I could help!
@whimsicalcellbooster
@whimsicalcellbooster 2 жыл бұрын
That clamp on the wood with the glue was deeply satisfying 😄
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Agreed! Woodworking can be very satisfying haha!
@bia_ven
@bia_ven Жыл бұрын
hello I am writing from Italy, I wanted to I saw that you nail but how do you close the holes? with wood filler? Thanks 👏🏽
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Hello! I used a 23 gauge pin nailer which creates a very small hole. It is small enough that you don't even need to fill the hole as it nearly invisible. But you can use wood filler if you want
@2hernandez562
@2hernandez562 Жыл бұрын
What material did you use for the slat to be ripped down to size?
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
I used oak but you can also use pine to save some money
@KokKeeYap
@KokKeeYap 2 жыл бұрын
Damn, this wall looks absolutely stunning! Great job!
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you, appreciate it!
@Pallidus_Rider
@Pallidus_Rider 2 жыл бұрын
Curious if slat wall helps with sound.
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Not much, but you can add black felt behind the slats if you want
@kicsipupi
@kicsipupi Жыл бұрын
very nice looking wall dude:) nice job
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Thank you!!
@elvisnigol745
@elvisnigol745 11 ай бұрын
What kind pf wood was being used here? In my region you can get only pine or spruce, not sure whether this wood works for this kind of wall
@GoldenKeyDesign
@GoldenKeyDesign 11 ай бұрын
You must not have watched the whole video. I go through our wood selection thought process and breakdown the pricing. Pine is an inexpensive option but we wanted to use higher end wood so we went with oak. Both species are sold most anywhere
@immadkhalid1887
@immadkhalid1887 9 ай бұрын
i might have missed it but how do you figure out exact spacing to make sure you get uniform look
@GoldenKeyDesign
@GoldenKeyDesign 9 ай бұрын
You have to measure your wall width and adjust your spacing accordingly
@mihaimtz6261
@mihaimtz6261 2 жыл бұрын
Great job! I want to see how u did the stairs, I didn't find the video on u Chanel, thanks!
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you! I actually have a couple videos breaking down the staircase. Here is the start to finish video: kzbin.info/www/bejne/oZDQeqywm8yamLc I also have videos breaking down the demo of the old spiral staircase (ep 2), filling in the old hole (ep6), framing out the new hole (ep 9), building the second floor landing (ep 10), and building the other landings (ep 11).
@josephinerussell8501
@josephinerussell8501 2 жыл бұрын
I always wanted to do slat wall for my house. Thank you for the video. Love how it turns out so much!!! Amazing job!!!
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you so much 😊 Good luck with your project!
@GoostavaRS
@GoostavaRS Жыл бұрын
Are you going to put a baseboard below the slats or is it best to leave it without a baseboard?
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
I designed it to not have one as I think it looks sleeker that way but you can add one if you want
@GoostavaRS
@GoostavaRS Жыл бұрын
@@GoldenKeyDesign thanks for the quick reply. It definitely looks sleek without one!
@JoelSherwood
@JoelSherwood Жыл бұрын
How much did this project cost you? how did you account for the different lengths of boards due to the uneven ceiling / floor ?
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
I used oak so it was around $700, but it can be done for $150ish if you use pine. I had to cut each board to a slightly different length (all within an 1/8") to get a snug fit for each board
@PeterKertesz2013
@PeterKertesz2013 Жыл бұрын
Beautiful finish.
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Thank you so much!
@humblenepali
@humblenepali 11 ай бұрын
Do you have video of how you did the outlet? I really wanted to know that specifically 😔
@baldontheworld7965
@baldontheworld7965 2 жыл бұрын
Really good piece of handwork.
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you, really appreciate it!
@bnbkhemani7965
@bnbkhemani7965 2 жыл бұрын
Great work. Looks great. Did you actually use pin nails or brad nails? I'm trying something similar but undecided on using 18GA brads or 23GA pin nails. My install has 0.75 wide boards for a small accent wall.
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you! I used pin nails and they worked great! The hole is so small it is practically invisible but you still can use wood filler if you want. They also have more holding power than you'd expect
@backtonatureitis
@backtonatureitis 2 жыл бұрын
Hi buddy! I love the way it looks! Quick question please. What if you have concrete wall, would the nail gun work or should I use other method?
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you! A nail won’t go into concrete but I think a heavy duty adhesive will work well
@backtonatureitis
@backtonatureitis 2 жыл бұрын
@@GoldenKeyDesign thank you and good luck with feature projects, you are doing a great job !
@carmelgrace6402
@carmelgrace6402 Жыл бұрын
looks amazing ..! definitely on my list as a project!
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Go for it!
@PatTheCat
@PatTheCat Жыл бұрын
What is the width of the boards & what was the spacing you used between the boards?
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Gap and width of boards are both 1.5”
@roadtoad919
@roadtoad919 2 жыл бұрын
I hope that you put box extensions on the electrical boxes. You did that right?
@Elonas
@Elonas Жыл бұрын
Nice work buddy 👏 like that you show the mistakes and accidents as no project in the world goes without them 😂 May I ask how much roughly it cost to do this wall (material wise)? I'm thinking should I do it myself or use premade Acupanels, they about $150 for 2400mm by 600mm 🤔
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Thank you! I try my best to show the ups and downs of my projects so I appreciate the feedback. We used oak so it was about ~$700. But if you use pine, it will cost about ~$150
@jeremysimpson7052
@jeremysimpson7052 6 ай бұрын
Might be a dumb question but what did you screw the outlet into since the outline took it away from the way?
@chris2ferUtoob
@chris2ferUtoob 11 ай бұрын
Nice job. really like how it turned out.
@TheBonafideMan
@TheBonafideMan Жыл бұрын
I used walnut colour stained pine and it's warmer than the yellow oak
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Got it, thanks!
@bankruptsee
@bankruptsee 2 жыл бұрын
What type of oak boards did you buy before ripping?
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Most of them were 1x8s but you can buy 1x2s if those are not available
@rustusandroid
@rustusandroid 2 жыл бұрын
How did you get the flush routing on the end U shaped piece to go all the way to the ceiling?
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Good question! I used a chisel to get the majority of it and then sanded it flush
@rustusandroid
@rustusandroid 2 жыл бұрын
@@GoldenKeyDesign I was really hoping for a magical answer, like elves come to finish it for you while you sleep...
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
@@rustusandroid if only haha!
@carshot0789
@carshot0789 2 жыл бұрын
"The level was calling my name... wanted to be used " was the best dialogue bro. Best wishes ☺️
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
I knew someone would catch that haha! Thanks for watching!
@corneliocapronidelatesta5094
@corneliocapronidelatesta5094 Жыл бұрын
I want to do something similar, but i have a concern. If some day i need to repair the light switch, how can you take out the wood to work on it ? I like a lot the finish and the aesthetic, but i it feels like it would be a little too permanent, and difficult to change
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
You can repair or change the switch no problem. The wood doesn't cover the light switch, it is just a border. It is no different to working on a light switch in drywall.
@corneliocapronidelatesta5094
@corneliocapronidelatesta5094 Жыл бұрын
@@GoldenKeyDesign Thanks for the answer
@JusFig
@JusFig 8 ай бұрын
could you paint the MDF boards before you put them up?
@GoldenKeyDesign
@GoldenKeyDesign 8 ай бұрын
You could but then you’d still have to caulk the edges and fill the screw holes
@chelin7023
@chelin7023 2 жыл бұрын
Love the design, the one thing I see as a maintenance problem is the space between the slats at the floor level; the debris, dog hair, dust accumulation.
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you! After a year of having it installed, I can tell you it has not been an issue. Because the depth of the slats are so shallow, a broom easily cleans in between them. I think it was worth it to not have a baseboard trim
@taisfogliatokurtz5598
@taisfogliatokurtz5598 Жыл бұрын
Look awesome! Well done!
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Thank you!
@roshanashta5650
@roshanashta5650 Жыл бұрын
did you nial them or screw them? cant see any screw or nail head please explain!!
@GoldenKeyDesign
@GoldenKeyDesign Жыл бұрын
Did you watch the whole video? I explain that I used pin nailer with 23 gauge nails
@andrewdc1
@andrewdc1 2 жыл бұрын
Would you recommend Danish oil or polyurethane? I have a can of poly at the house but was wondering why you chose the oil over that
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Good question! I normally use poly but for this project, the wood didn’t require that much protection, it was a bit overkill. You still can use poly but I didn’t want to have to wait for it to dry and then sand and then add another coat. Danish oil goes on in one coat and it dries very quick hence why I choose it
@andrewdc1
@andrewdc1 2 жыл бұрын
@@GoldenKeyDesign Thank you! Also what gauge nail gun did you use to keep the oak slats on the wall. I'm mid project and 18 gauge Brad nails were not strong enough to go through 😔 I was thinking maybe I need to switch to a 15 or 16 gauge finishing nailer. I should mention my slats are mounted almost directly to my wall so no MDF board behind them.
@williambeard5526
@williambeard5526 2 жыл бұрын
Looks stunning. I always wonder how much it would cost to get someone in. It's part of the reason I do most of my own work. Well done. 👍
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you so much! I do most of my own work for the same reason haha
@nickorsini2975
@nickorsini2975 2 жыл бұрын
Crushed the spacing, and covering that gap was poetry. I'm about to attempt vertical wood slats as a staircase partition and came across your video and channel. Subscribed!
@GoldenKeyDesign
@GoldenKeyDesign 2 жыл бұрын
Thank you so much, I really appreciate it! Good luck with your build and thanks for the subscription!
How to Install Slat Wall Panels With LED Lighting Built in!
12:47
The DIY Guy
Рет қаралды 194 М.
DIY Wood Slat Wall | Step By Step Stairway Wall Demo & Makeover
16:00
Sigma Kid Mistake #funny #sigma
00:17
CRAZY GREAPA
Рет қаралды 30 МЛН
99.9% IMPOSSIBLE
00:24
STORROR
Рет қаралды 31 МЛН
UFC 310 : Рахмонов VS Мачадо Гэрри
05:00
Setanta Sports UFC
Рет қаралды 1,2 МЛН
Akupanel Installationsanleitung mit Montagekleber
2:52
WoodUpp Germany
Рет қаралды 1,5 МЛН
Save Money Building Your Own Slat Wall
14:53
Proper DIY
Рет қаралды 571 М.
How To Build a Wood Slat Wall With Floating PC Desk!! 🤯😍
14:05
Burglars Hate Me For Showing You This!
27:46
HAXMAN
Рет қаралды 3,1 МЛН
How to Create a Hidden Door with Wood Panelling | Trepanel
12:12
Walls and Floors
Рет қаралды 273 М.
How To Build A Slat Wall | STEP BY STEP GUIDE
17:15
Would Wood Work
Рет қаралды 147 М.
How to Add BEAUTIFUL Wall Lighting (SUPER EASY!!)
8:43
Ahnestly
Рет қаралды 334 М.
DIY Greenhouse | Don't Buy a Kit Until You See This
19:04
April Wilkerson
Рет қаралды 668 М.
Fast & Final Walls: No Tape, Mud or Paint | Durable and Easy to Clean
8:21
Build A 12'x20' Modern Shed and Deck by Yourself: With Material List
23:18
Niles Productions
Рет қаралды 1,7 МЛН
Sigma Kid Mistake #funny #sigma
00:17
CRAZY GREAPA
Рет қаралды 30 МЛН