Build A 12'x20' Modern Shed and Deck by Yourself: With Material List

In this video I set out, with my trusty dog Hanson, to build a 12x20 modern shed all by myself. Check Below for Material and Tool List.
I hope you are ready for my Bob Vila impressions as this video has some serious This Old House Vibes.
All kidding aside I would love to know what you think.
Feel free to ask questions about the build and I'll do my best to respond.
Tell me what you liked or what you would have done differently.
Tools Used
Circular Saw, Chop Saw, Jig Saw, Hand Saw
Impact Driver, Drill, 18ga Narrow Crown Stapler,
Dead Blow Hammer, Level, Speed Square, T-Square, Tape Measure, Razor Knife, Caulk Gun, Tin Snips
Shovel, Garden hoe, Harbor Freight Power Auger with 8" auger
Material List
Material list: Foundation and Sub Floor
10 8” Sakrete Form Tubes
16 bags 80lb Sakrete Fiber Reinforced Cement
20 3/8” x 36” rebar
10 4x4 Concrete Pier Hangers
2 4”x10” 20’ PT Beams
16 2”x10” 12’ PT Joists
28 Galvanized Joist Hangers (Fasten with Structural Screws or Joist Hanger Nails)
64 Headlok Lag Screws
1 Roll 12’x20’ 6 MIL Black Plastic
8 3/4” 4’x8’ PT Marine Plywood
Wall Framing
Rear Wall:
3 2”x4” 20’
18 2”x4” 8’
Side Wall No Window:
3 2”x4” 12’
10 2”x4” 8’
Front Wall:
2 2”X4” 20’
4 2”x4” 10”
18 2”x4” 8’
2 2”x6” 20’
1 2”x6” 8’
Side Wall With Window:
2 2”x4” 12’
12 2”x4” 8’
1 2”x6” 8’
Top side wall angle framing
2 2”x4” 12’
3 2”x4” 8’
Wall sheeting
19 ½” 4’x8’ CDX Plywood
Rafter Framing
28 Simpson Steel Rafter Tie (Fasten with Structural Screws or Hanger Nails)
Rafters:
18 2”x8” 16’
Nubbins:
2 2”x8” 16’
Rafter Fascia:
3 2”x8” 16’
Roofing,Fascia, and Soffit:
Fascia and Soffit
4 1”x10” 20’ Cedar
24 1”x6” 12 Tongue and Groove Cedar
Roofing
12 ½” 4’x8’ CDX Plywood
3 2” 10’ Drip Rail
2 36”x66’ Stormguard Roof Underlayment
17 16” 16’ Skyline Standing Seam Roofing Panels
3 Skyline Peak Panel Caps
4 Gable Caps
2 Rolls of Butyl tape
24’ Skyline Peak Foam Enclosure Inserts
Windows and Door
1 30”x36” Window
4 48”x24” Windows
2 Rolls of Self Adhesive Window Flashing
2 OSI Quad Window and Door Sealant
1 Jamsill Sill Pan
1 Pack Door Shims
1 Therma-Tru Fiberglass Door
Siding
1 Roll 9’ Tyvek Homewrap
1 Roll 2” Tyvek Tape
1” 12 Gauge Galvanized Cap Nails
13 5/8” T1-11 Plywood Siding
4 1"x3" 8' Cedar back corners over siding
2 1"x3" 12' Cedar front corner over siding without shingles
3 ½”x5/8”x2” 10’ Gibraltar Galvanized Z Bar Flashing
6 Bundles 1.5 Square Cedar Shingles
Deck
5 Pier Block With 4x4 Hangers
26 Joist Hangers (Fasten with Structural Screws or Joist Hanger Nails)
70 Headlok Lag Screws
1 4”x6” 8’ PT
14 2”x10” 12’ PT
8 2”x6” x 12’ Deck PT
23 2”x6” 8’ Deck PT
1 2”x8” 8’ Deck PT
Stairs
6 Pier Block with Framing Notch on Top
6 3 step PT Stair Stringers
6 11.5”x48” PT Stair Tread
Privacy Wall
30 1”x4” 8’ Cedar
3 2”x4” 10’ PT
1 4”x4” 10 PT
12 Headlock Lag Screws

[@tamarathecreator1111]

I would have loved to see the inside

[@NilesProductions]

Check out my follow up video I recently posted about making it solar powered. You can see a bit of the inside. Mostly just shelving and a couple work benches as I did build it to be a storage shed/bike shop. kzbin.info/www/bejne/bWXHq4ilh658mtk

[@Vanessa123nice]

How can I buy plans for this project? Please forward your email or contact info

[@mrwck1953]

@@NilesProductions How's the solar treating you?

[@NilesProductions]

@@mrwck1953 So far so good. I bought a little propane heater to warm things up during the winter so I've mainly been using the solar generator to power my lights, electric drums, and guitar amp. Zero issues, been super reliable so far. I must say I'm pretty happy with it. If I were convert the shed to a full time use space, like using it for an office or studio, I'd probably want power from the grid though. Solar generator is perfect for how I use the shed.

[@rccpromotions]

​@@NilesProductions this was an awesome video! How much did it cost in materials to build?

[@MrVitorio007]

This book is Awesome! I love the Lean-To-Shed the most (page 98). The plan kzbin.infoUgkxe9yi0sulKgsp0VJJCIrLWWkvVqcU7LFR is to attach it to the back of my brick house. I also like how they walk you through the many different steps of construction, which is important for the less experienced like me.

[@orionred2489]

Step 0... tell your wife you're gonna be busy for six weeks.

[@mikerooney7600]

This video is truly a gem. You walk away knowing *exactly* how to do every step of this build. No 1,2 skip-a-few. There should be an award! Thank you

[@NilesProductions]

Thanks Mike! Glad you enjoyed the video 🤙

[@StormyMonday0896]

there are a number of things that could be improved.

[@ThingEngineer]

I’m not sure at what point this went from shed to tiny house. Awesome job!

[@NilesProductions]

It's still all shed on the inside. Just some shelving and a work bench. LOL Glad you liked it Josh :)

[@AndrewOvenden]

Oh come now, who hasn’t ever ended up with a much larger project than originally intended. What I tell my wife I’m building, and what we end up with frequently don’t match.. Not sure how that happens 😃

[@tortron]

For legal reasons you have to say its a shed lol

[@glenedajoseph2843]

That is what I am saying

[@enrique88005]

@@tortron os that what it is. Then that is an outstanding shed

[@lordvonmanor6915]

Oh geez, this is the nicest shed I've seen on KZbin.

[@NilesProductions]

Thanks Lord von Manor! It's the nicest shed I've built for sure.... it may be the only shed I've ever built but I feel it turned out nice. lol

[@jameskirk3]

For sure. 16' centers would stand up to a heck of a load of snow.

[@jameskirk3]

@@NilesProductions how much did this cost?

[@NilesProductions]

@@jameskirk3 the shed and the deck was a little over $12k

[@MrSlimification]

@@NilesProductions aa

[@LibbyClarkeStudio]

First of all, what a great dog! Second, I am so inspired! Thank you! I will be building my own shed soon and this is SO helpful!! I will need to insulate mine a bit, but with this design that would be simple!

[@NilesProductions]

Best dog ever :) As a foreman he could be a little harsh though... always barking orders and telling me my cuts look ruff. Thanks for kind words I'm glad you liked the video Libby Clarke

[@danterusso6354]

Beautiful project!!! Two things: It would have been equally amazing to see electrical/water ran as part of the build. Also, how great would it be to have a ‘roll-up’ or ‘barn door’ entrance on that wall in the front? With that said: I can’t do what you do and my thoughts are part of a wish list for a similar building in our backyard. I am VERY appreciative of you for sharing this!!!

[@NilesProductions]

Thanks Dante Russo :) At the moment I have no plans to run water inside the shed maybe add a hose bib to the outside? The water main from our well runs right next to the shed so it shouldn't be to crazy to install. For electricity I plan on adding a solar generator for lights/small power needs. I considered installing a roll up door on the side but decided against it in the end as I wanted to maximize shelving and storage on the inside plus I already have a small garage off the main house for larger storage needs.

[@darinking1343]

I'm just curious, ballpark, how much do you think the materials were for everything? I think it looks wonderful. Great job! The only thing I would add is insulation as it gets pretty cold here, and if it were my escape room, so to speak, I'd want a little heat in it. ;). Again, awesome job!!

[@NilesProductions]

It was a little over $12k for deck and shed at the time of my build.

[@GuitarGuyAl]

I'll be starting my own 10x12 build in the coming months. Feels like a massive undertaking already - just in the planning stages. Videos like yours make me feel like it is possible.

[@NilesProductions]

This was my first shed build. It was a little intimating when I started but I took my time and tried to think things through. As the build progressed and everything started falling into place I started feeling more confident. Once finished I was really happy with how things turned out and am glad that I stepped out of my comfort zone and decided to build this vs buying a pre built shed or paying someone else to do it for me :)

[@eltiburon5240]

How much did you spend on this build?

[@NilesProductions]

@@eltiburon5240 It was a little over $12k for shed and deck at the time i built it

[@wrlprchnx]

Almost makes me sad I just went with a Fibreglass pre-built (basically lego) shed for my back yard with how beautiful this looks

[@NilesProductions]

@@wrlprchnx Nothing wrong with going pre-built. I'm glad you liked the build. Thanks for the kind words, Marc Seewald.

[@DanielRichards644]

Joists sitting on Joist Hangers (properly attached to Joist Hangers) don't need the headlok screws from the outside, thats a chunk of change that didn't need to be spent. Also depending on your region and local codes consider Slab on Grade so that you can park a Mower or other equipment in the Shed. Side Note, after setting the "outer frame" of the floor (the 2 end joists and 2 big beams) check for square then and adjust before bolting the plates set in the concrete to the 4x10's, I'm sure you thought of this, but since it wasn't shown felt worth mentioning.

[@julietphillips1991]

I can well imagine how very rewarding this was! It's beautiful and you did a super job!

[@NilesProductions]

Thanks Juliet, it was a good for the soul for sure.

[@gregwytcherley]

I am in the planning phase of my backyard shed and this inspires me to do it all myself. The pride you must have is well deserved. Thanks for including the supply list as I might use that. Great build and the video was well done! I'm a little worried about my foreman but I'm sure a few tosses of the ball and some treats he will be encouraging.

[@NilesProductions]

A good foreman will bark orders and let you know when your cuts are ruff. Good luck with your build :)

[@markf.4063]

You don't use deck screws on joist hangers. That would fail inspection in a heartbeat not mention that screws shear strength is shit compared to the proper fastener....either joist hanger nails or structural screws.

[@NilesProductions]

You are correct, I should have used structural screws instead of deck screw for the hangers. I'm not a professional carpenter and am learning as I go... Here is a good video about shear load and screws vs nails for anyone looking to learn more. kzbin.info/www/bejne/p57Em357odOqnKc

[@garystew2077]

It would be cool to have a rain collection system off of that roof! And it would be so close to your awesome garden. I'm looking to do a shed/rain collection build sometime in the future and will definitely be utilizing this great video. Thank you!

[@NilesProductions]

Yeah, that would be handy 🤙

[@denisesmith209]

I am so glad I stumbled across this. It is almost exactly what I will be building on my land. Thanks for sharing. Nice job!

[@NilesProductions]

Glad you enjoyed the build, thanks for the kind words 🤙

[@bfroutdoors]

Great video man! Huge thank you! I am about to start building a 12x20 cabin in the mountains and I have been debating how to make the two main beams, seeing your 4x10x20 beams I found my solution. Lots of information here so again thanks!

[@NilesProductions]

Very cool, If I ever build another one I want it to be a cabin in the mountains or at least the middle of nowhere.

[@MDavilus]

I’ve watched a lot of shed videos and this is by far the most detailed. Great job. Hope to it one day.

[@NilesProductions]

Thanks Mark Davilus! Glad you enjoyed the video and build 🤙

[@Coolkid-up4vi]

Screws in hangers may not meet code in some circumstances

[@JasonExplainsThings]

Ben! This video was fun, inspiring and informative. DIY video gold. I'd love to see a follow-up video on what you did with the interior. Congrats on your beautiful project.

[@NilesProductions]

Thanks Jason! It might be cool to do a walkthrough and show off the inside. It's really just a garden shed/bike shop on the inside, looks way fancier on the outside lol

[@bernisrogerson9224]

Built better than 99 percent than most homes due to actually 1/2 & 3/4 plywood not particule board or glued flake wood

[@NilesProductions]

As a younger man I built a lot of skateboard launch ramps and a couple half pipes. Learned real quick that the osb/waferboard doesn’t hold up to the elements very well. I also noticed that all contractors tend to use plywood on their personal homes…

[@adammm8964]

Hands down one of the bed shed build / edits, keep it up would love to see the inside and your plans there !

[@NilesProductions]

Thanks for the kind words Adam m m. I currently plan on keeping the inside pretty simple, just some shelving and a workbench. I'll probably add a small solar generator in the future for lighting and power needs. When I do I'll make a little walk through video.

[@alfredsarkodie3909]

Loved the background music.

[@NilesProductions]

The music is from Zachariah Hickman :) Glad you enjoyed it

[@anniesthesia]

Those paw prints are seals of approval.

[@NilesProductions]

I wish I left them

[@olybears57]

“How to build a shed for yourself….. firstly, take out a $50,000 loan….”

[@NilesProductions]

LOL, It was a little pricey as far as a DIY shed goes. All in it was a little over $12k for the shed and deck. You could make it a little more affordable by using OSB sheeting and forgoing the metal roof, and all the pressure treated lumber in the foundation and floor. Also the cedar shingles and T&G was really expensive. Had I not used premium products I probably could have saved a couple thousand dollars for sure.

[@johnlysic6727]

Most excellent! I have built 2 sheds on my own but never one this nice- I do need to build one with my middle son next summer, so some of your process will definitely be helpful - thank you

[@NilesProductions]

Glad you liked the build 🤙 This was my first shed build. I learned a lot along the way. The main things I regret was not installing insulation under the subfloor before I laid down the plywood. Probably add it when the weather improves but I have a feeling it’s going to be a little tricky. Lol

[@IvanYanev]

I'm still processing the fact that he built that tiny little house on his own ! Hats down ! I have no intention to build anything but still I find you video very satisfying and I really enjoyed it ! Thank you

[@NilesProductions]

Thank you Ivan! Glad you enjoyed the video and build. 🤙

[@ragnarlothbrok3948]

Amazing shed. Really impressed he did all that in only 24 minutes.

[@NilesProductions]

I work fast lol

[@MilenaKoncar]

How much money in materials did u use for the foundation and steucture without counting the metal roof and siding?

[@NilesProductions]

The full shed and deck was a little over $12g a the time I built it? I don’t remember what the individual sections cost as it’s been a couple years but you could take the material list in the video description to your local lumber yard to get more accurate pricing. I have the materials broken down into separate sections.

[@wendellf8659]

Hands-down the best shed build on youtube.

[@NilesProductions]

Thanks Wendell F! Glad you liked it :)

[@elginx]

Great work!!! Any thoughts on rain collection off that roof for your garden? Thanks for sharing!

[@NilesProductions]

That's a great idea. We have kicked the idea around a little.

[@stevenbuffalohead2509]

I’m looking to build a 12x16 “finished” shed, for a backyard office. This video really sums up the structure process. Would you do anything differently with plans to finish the inside? We have a 4 season climate. Thanks and amazing work btw!

[@NilesProductions]

I’m pretty happy with my design for the most part. If I was to use it as a studio or living space I might want bigger windows? I should have used structural screws or hanger nails when installing my joist hangers. Maybe synthetic deck boards? Glad you liked the build Steven.

[@davidcamacho444]

would using a thick concrete slab offer any benefits in cold climate areas (north east)? Perhaps insulation between floor joists an option?

[@bobibobber2913]

Mate,it absolutely looks cracking but I bet it does cost a small fortune.

[@NilesProductions]

Thanks Bobi Bobber :) Glad you liked the build. All in the total cost was a little over $12k for the shed and the deck.

[@L.Scott_Music]

When setting your joist hangers try fashioning a metal bracket to the top of your scrap 2x10 so it hangs on the beam even with the top. Metal strap screwed to the top of the scrap bent into a L shape to clip around the bean outer edge. Really nice job. Much envy.

[@smitaaay]

That's a good idea. I'm gonna do that. 👍👍

[@oorange0621]

I thought your dog was a bear for a second! LOL Beautiful video! Thank you!

[@NilesProductions]

Glad you liked the video :) Your not the first to say he looks like a bear. In the past, out on the trail, he has been mistaken for a small black bear by people a couple of times LOL

[@MrPicklejuice98]

As a carpenter, you did some really solid work! A few things I would've done differently, but overall a really nice shed. Mainly, larger joist hangers with proper hanger screws instead of construction screws. But I think your method will hold up for decades, so I'm probably just being particular

[@NilesProductions]

Thanks! If I ever build another one I’ll do bigger hangers for sure and nails or hanger screws to fasten it 🤙 After three years it feels as solid as the day I finished. I’m pretty proud of the build being it’s my first shed and all 😆

[@MikeBertelsenDK]

I am so impressed! I wish I had the knowledge to do things like this. I'm looking to buy an isolated office for my backyard. I work remotely everyday so it would be nice going out in the backyard to work. I've been looking at prebuilt solutions but they are very expensive. What did a solution like this cost you if I may ask? No matter what, you are extremely skilled and I enjoyed watching the clip.

[@NilesProductions]

I built this in 2020 (during lockdown) when wood prices were a little bit high. All in it cost me a little over $12g for the shed and deck. Glad you enjoyed watching my little build/video :)

[@brianparker859]

AMAZING WORK! I am just beginning to prep my site for a new cabin and wanted to go modern with rustic elements-- precisely as you have done. Bravo on your craftsmanship! How did you finish the inside? And do you happen to have a list of all the materials?

[@NilesProductions]

The interior isn’t finished as I really did build this to be a shed. It’s just some shelving, storage boxes, and a work bench. I plan on adding a little solar generator for small power needs and lighting in the future. You will find the material list in the video description

[@peterchoi1825]

I'm in the planning process of my back yard office as well for 10'X20', I was wondering why you went with the 4"x10" beams for the foundation? I saw some people went with 2"x6" and was going to compromise and use 4"x6"s. Do you think this will make a huge structural difference? Also, I was going to add a middle layer of piers, think that's overboard?

[@twzimage]

Great job Ben! I’d love to see the finished interior as well.

[@NilesProductions]

The interior is just shelving and a work bench...I could do a walk through video maybe and show off how it's organized?

[@NilesProductions]

Check out my follow up video about making it solar powered. You can see a bit of the inside. kzbin.info/www/bejne/bWXHq4ilh658mtk

[@NilesProductions]

You can see a little bit of the inside of the shed in my video were I set it up with solar power kzbin.info/www/bejne/bWXHq4ilh658mtk

[@themikevlad]

Very nice job! What was your budget for this build?

[@NilesProductions]

It ran a little over $12k at the time of the build for the shed and deck.

[@runewafflz8264]

This is beautiful. Simply amazing. You made this look so easy and fun. Really motivating to us future carpenters and DIY home owners

[@NilesProductions]

Thanks Rune Wafflz! Glad you enjoyed the video and build 🤙

[@xisotopex]

I feel like I have pretty sold idea of how to build a simple shed.... what I lack is some particulars.... for instance, I want the shed to be as low as possible, not much taller than 7' at the leak, and the plans dont have a top plate, which I feel is essential, but I am not sure how much that extra 2x4 is going to change like the soffit installation, or what ever is done to make sure under the eaves is water tight.... also. I want to extend the eaves and again not sure if that would fundamentally change some part of the build... do you have any good resources to get more info on this? thanks

[@NilesProductions]

I found this book very helpful when I was designing my shed. www.amazon.com/Sheds-Garages-Building-Storage-Structure/dp/037601377X/ref=asc_df_037601377X/?tag=hyprod-20&linkCode=df0&hvadid=692875362841&hvpos=&hvnetw=g&hvrand=7972531751063532852&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9033270&hvtargid=pla-2281435177658&psc=1&mcid=ce05c2b183cb3cb58b5cfc9e49ecaa24&hvocijid=7972531751063532852-037601377X-&hvexpln=73

[@AndrewThronImprovements]

Awesome build with great, detailed instructions! As someone who just built a 10'x10' modern shed, it was great to compare notes. Adding the top plate before lifting the walls vertical was a way better idea 🤣 I went with standalone T1-11 (no plywood sheathing beforehand) as the siding, used a steel roll up door, and went with a asphalt shingle roof. Installing the soffit was probably the most brutal part of the build - at least for me. Curious to see if you felt the same. For my 10'x10' I spent around $3,600 for materials (steel roll up door was $450 of that). You went the extra mile on nearly every aspect of this build, so I am guessing around $8,500? I am currently editing my Modern Shed Build Video for my Channel - so I appreciate the time that went into filming the building process and the editing time afterwards. Excellent job!

[@NilesProductions]

Glad you liked it! I'm a little over $12k into mine with the deck. When I started I budgeted $10k but wood prices kept going up throughout the build. T&G soffit is a nightmare but it looks so good lol. I would love to see your build when your video is done. Reply back with a link when it's up :)

[@clreed9690]

Thanks for sharing your costs!

[@NilesProductions]

@@clreed9690 No problem

[@AndrewThronImprovements]

@@NilesProductions Worth every penny - Looks awesome. And will do! Plan to release it in early Spring 👌

[@Mezzanine99T]

I wondered about the value of plywood sheathing under the T1-11 as well. I suppose it's serving as a shear panel?

[@FortniteOG420]

Most overkill built shed or well built tiny house, you decide

[@NilesProductions]

Perfect place to cook am I right Walter White? 🤣 All joking aside, thanks for the kind words it means a lot.

[@gerryvalentine7671]

I am in awe, by your build quality, your video quality, and your wonderful garden...but especially your old timey fuzzy foreman !! These are the perfect videos to decompress to after a stressful day. God bless you all !

[@NilesProductions]

Thanks Gerry! The fuzzy foreman is the best and why I actually I got around to editing the video. I wanted to watch him cruise around and get up to mischief on video :)

[@brendanramroth3067]

Awesome craftsmanship all the way around. Great videography too. I am curious, were you a carpenter or a framer before you started this project? again, nice work and thanks for sharing.

[@NilesProductions]

Thanks Brendan Ramroth! I am not a carpenter or framer by trade. Just a guy that likes to DIY stuff. Most of my experience comes from building skateboard ramps and half pipes in my youth. With that said this isn't the first time I've swung a hammer but it is the first time I've built a shed. I'm happy I took the initiative and did it myself vs buying a prebuilt shed at Home Depot. I learned so much by researching and doing this project. Really proud/happy with how it turned out.

[@brendanramroth3067]

@@NilesProductions I should have known by the low top, slip on checkerboard Vans in the video. You really took your time and did it right. Gives us all hope to tackle those bigger projects. Thank you for sharing.

[@namelesscleric6657]

Excellent job, very inspiring. Also thanks for the material list helps to put the scale of the endeavour into perspective.

[@NilesProductions]

Thanks Chikwanda, glad you liked the build :)

[@derrickdzierzynski2508]

This shed would def sell as a house for 500k in the PNW

[@NilesProductions]

Need to crank out a dozen tiny homes 🤣 Glad you liked the build Derrick

[@jaylay9524]

The editing for this video is absolutely perfect. It shows everything without getting monotonous. Nice work. I know that's much more difficult than it looks.

[@NilesProductions]

Yeah, I sat on the footage for more than a year before I started editing it. No one in their right mind wants to sift through 18 days of footage 😆

[@Jin420]

I really thought I had my plan together for my shed ---- until I saw this.. 🤦🏻‍♀️🤣🤣💯 Edit: I'd make a side door for my mower, though.

[@NilesProductions]

Glad you liked the video Jin! Making the build suit your needs is the key for sure. A side door would be nice for bigger equipment.

[@breavofox360]

Very nice! One of the very few she build videos I’ve watched start to finish.

[@NilesProductions]

Thanks for the kind words Breavo Fox 🙌

[@rfldss89]

Is it not common practice to add a layer of wooden slats under your final roofing/siding layer in north america? In europe it's a requirement, to add ventilation and avoid moisture damage.

[@NilesProductions]

Good question? I’m not 100% sure if it should be required for the siding in this case but with the roofing I selected there are little ripples in the the steal that allow for a small amount of moisture or air flow under the sheets.

[@rfldss89]

@@NilesProductions I think best practice where I'm at still dictates you should add slats behind siding to allow for airflow, because eventually some water will probably seep through, or just soak through the shingles and the quicker they dry, the better. But maybe differences in climate make it unnecessary in certains parts of NA.

[@ceciliaescobedo5624]

Loved watching your video. It was really educational and entertaining. Learned a lot. My husband and I have a small old house. It's practically ready to be bulldozed. However, you gave me some really great ideas as to how we can salvage some of this 1949 old little house. God bless.

[@itscoppertime]

Great video. Love the Firefly-esq music.

[@Mars21681]

Inspiring. And one of the best build videos I've ever seen. Thank you!

[@NilesProductions]

Thanks for the nice comment! Glad you enjoyed the build and video 🤙

[@mrwck1953]

My favorite modern shed video. Really, thanks for sharing. Couple questions. 1. Do you recall the height of the front and back walls? For the shorter, you mention 2x4x8s. Were those cut down or used at the 8' length plus bottom plate and double top plates? So 1.5+1.5+1.5 +96"? Same for the front wall. 2. Did you consider blocking out the sub floor or were the 2x10s rigid feeling enough across that 12' span? 3. Where'd you get your windows? 4. Other than using more nails, maybe taping top of floor joists, and insulating the floor, anything else you would have done differently? Again, great build!

[@NilesProductions]

Thanks Mr WCK! Glad you liked the build. All the boards were cut down. When I mention the lumber size in the video I'm referring to ruff dimensions. I don't remember the exact lengths that I cut the boards to so I was just letting you know my raw material size. The floor feels super ridged despite no blocking. I ordered my celestial windows through Lowes, the single wall window I had left over from my home remodel. Things I would have done differently: Insulate the floor with ridged foam before putting the sub floor down for sure. Used nails in the hangers. Not called birdmouth rafter cuts "birdbox" cuts lol Maybe add a little fire place for heat in the winter?

[@kieronmonahan2349]

Great video, thanks for taking the time to produce this and edit it, so helpful. Now I want to/need to build one :-D

[@NilesProductions]

Thanks for the kind words Kieron Monahan 🤙

[@JasonExplainsThings]

The views are climbing! Well deserved Barnyard!

[@NilesProductions]

Thanks homie 🤙

[@Shellz006]

You did an amazing job and I think you have convinced me to give it a shot! I'm looking to do pretty much exactly what you did but 12 x 24 ft instead. I think my biggest hurdle is doing the foundation. I've never had to level something so large. Have any tips on doing the foundation or have a video?? Anyways thanks for making this video. I'm sure you are helping a ton of people by sharing this.

[@NilesProductions]

Thanks Sheldon Gray. I found the batter board method for laying out the foundation to be very useful. The 3-4-5 measuring technique is key in making sure everything is square. Also they make these little bubble leveling tools that hang on the line as well that work great. www.amazon.com/Rope-Bubble-Level-Hanging-Leveler/dp/B07Y8GPJ7H I personally don't have a video showing the method but there are a ton of them across KZbin that should show you the basic concept. kzbin.info/www/bejne/routZ5V7o5V7h7s

[@Shellz006]

@@NilesProductions Thanks for the info man! I really appreciate it! I will definitely look into those.

[@robertforster9482]

If you build a deck longer than the building this gives you outside working and relaxing space. You need it after a hard day in the shed.! 😄

[@Shellz006]

@@NilesProductions I forgot to ask do you know the shed height from highest point of the roof to the shed floor? I'm trying to see if this falls within my 12 ft height limit.

[@NilesProductions]

@@Shellz006 From the floor to the peak cap it's aproxamently 11'. From the bottom of the 4x10 beams it's just under 12'. My front wall is just under10' and the rear wall is just under 8'. The over hangs is 30" in the front and 18" on the back

[@Jin420]

If I can build this, then I can build a house. 💯🤣 Or at least be 72,346 steps closer towards building one on my own one day. 💯😏

[@NilesProductions]

You can do it if you put your mind to it 🤙

[@jnorris8649]

You should’ve used nails for the floor joist hangers. They have much higher shear strength than screws. I found using a pneumatic palm-nailer was the best way to get into the relatively tight spaces.

[@NilesProductions]

Good advice for sure

[@051biohaz]

I thought that too, until I saw the head-lock’s from the outside

[@NilesProductions]

According to Hilman’s technical data for the Deck Plus #10 screws I used the sheer strength is 2317 lbs. stfasteningsystems.com/deck-plus/#12type I should have used their Structural screws instead of the deck screws as the head sits flush against the hanger vs how the deck screws head is tapered.

[@jnorris8649]

Not trying to miss the forest because of the trees- That shed & deck are gorgeous. Glad you tracked down the tech-specs. It should be alright. Manufacturer approved, application-specific fasteners are an obvious alternative. I will, however, point out that the specs do not suggest joist hangers, or any metal connectors for that matter. I can only assume one reason is the risk of galvanic corrosion when the coating is inevitably stripped as the screw is driven in. This causes the bare metal of the screw to be in direct contact with the dissimilar metal of the hanger. Being exposed to humidity/moisture in general, or even the chemicals in the treated lumber is the last ingredient for fairly rapid oxidation. I’m no engineer, but I’ve done my fair share of home repair, demo, and renovation. I had to renovate a shed, which included gutting/replacing the rotted floor. I spent days and days reading building codes, tips/tricks, etc., and I came across the “don’t use screws for joist hangers” thing. Inspectors will literally fail an entire build if the see 1 unapproved screw in a joist hanger. I’m 110% a “why-guy” & this struck me as a bit extreme, so I chased it down until I came across what made the most sense to me to be the answer. I can’t necessarily tell you where I found it, but wood screws(i.e., deck/general purpose) are specifically designed for tensile loading, rather than radial/sheer loading. When a screw is used to fasten something, it is essentially being stretched as it’s torqued. Having something push on the side of a relatively brittle fastener that is already under tensile load is asking for trouble. Nails(i.e.,10d/16d), however, are not dealing with any real tensile loading. Sure, there’s friction holding them in the wood; but they’re not being stretched. This allows them to be more reliable/robust when dealing with radial/shear loads, or even any movement resulting from the edifice settling. Plus, they’re typically galvanized to inhibit corrosion. Again, I’m just here to share info that will hopefully help.

[@051biohaz]

@@NilesProductions I didn’t mean to come off critical, the shed looks great dude. Really nice job with the t1-11 and the cedar shingles..:)

[@nasionalsb]

greetings from Costa Rica, very nice project my friend!!! SALUDOS!

[@NilesProductions]

Thanks! Glad you enjoyed the build 🤙

[@CrosshairLunchbox]

Those brown decking screws aren't made for the shear load of a hangar application. The hangars should be used with nails or the Simpson structrual screws that are stocked near the hangars at the big box store.

[@NilesProductions]

Thanks CrosshairLunchbox. You are correct, I should have used structural screws instead of deck screw for the hangers. I'm not a professional carpenter and am learning as I go... Here is a good video about shear load and screws vs nails for anyone looking to learn more. kzbin.info/www/bejne/p57Em357odOqnKc

[@juniorcarmack8741]

And you only used 2 x 6 hangers for 2x10s they actually sell 2 x 10 hangers so that way the hangers actually a lot taller to get more nailing surface so the board doesn’t twist

[@xpert1111]

true but didn't he add lag bolts to each joist at the exterior side of the rim band? He should be good

[@rgbking488]

@@juniorcarmack8741 any big diff between nails vs construction screws? Forgetting the obvi work of screwing vs nailing. I'm talking like structurally....are screws better? Or what's the dealeo. Curious because I'm going to rip on one of these here this next year

[@D-Z321]

@@rgbking488it’s not whether one is better than the other…. They’re used for different purposes. Nails for “moving or shifting” points, screws for weight or gravity points. Example ive heard used is to screw a screw and hammer a nail equally into a board, then try pulling the nail out and then try pulling the screw out. The nail comes out more smoothly, the screw probably won’t come out. Now, whack the exposed nail and then the screw from the side. The nail will bend, and the screw will most likely break off. The nail handles movement better, while the screw is better for retention…

[@FranklySpeaking73]

Thanks for the video and insight. Awesome knowledge and skills! It just feels too fast and like you skim over some important details. Can you imaging a surgery video or computer tech video being done this way? 😮😂😂 Exactly.

[@NilesProductions]

The ol editing balancing act of keeping something watchable vs instructional will get ya every time lol. Sometime I want the cliff notes and sometime I need the whole book. I hope you found some inspiration in watching the video even if I didn’t get to deep in the weeds. 🤙

[@TheBellvueRanch]

Awesome build! Thank you for sharing! We are designing something similar, this is a great inspiration!

[@NilesProductions]

Awesome Tom George! I'm glad you enjoyed it :)

[@compubyte2010]

WOW .. just WOW.. ok,, you said.. "Tell me what you think?" .. ok. well what I think is .. you should come to my home and built another one.. that's what I think.. :) Great JOB!!!

[@NilesProductions]

Wouldn’t it be cool if people showed up at secret community build project and would build stuff for those in need. Kind of like geocaching but instead you post coordinates and a building plan online and then people randomly show up with a pice of lumber or something needed to slowly construct the project?

[@benhoff8443]

Thanks for doing the video. You did a great job! Has anyone else already commented about doing your sheathing wrong? You placed your plywood vertical but you want the 8’ running horizontal and then stagger. You give it a lot more structural stability.

[@NilesProductions]

You are the first to make this comment. What you say makes sense though and is good advice.

[@ian18dudley]

No you’re installing the plywood correctly. Installing the plywood vertically allows you to nail rim joist, bottom plate and top plate all within the same sheet. If your sheet doesn’t reach the top then just add a row of blocking.

[@rgbking488]

@@ian18dudley so what was that guy saying about adding more "structural stability?" Doing them vertically is more stability, but horizontally is the standard?

[@AnthonyWeatherby]

Thanks for the tutorial! I used this video to build a similar tiny home. Really appreciate the time and effort you put into these videos to make them accessible. Did you end up venting your soffit? If so, what did you use?

[@NilesProductions]

Soffit Disc vents work pretty well :)

[@conorreynolds9739]

Really enjoyed this video. Seeing you get everything square was impressive. Really well thought out and organized, I’ve got a termite-ridden shack out back that a replacement like this would be perfect for. As someone who’s been working on a never ending house renovation for over a year, it’s soothing to see something taken near completion in one video…how long did this take you?

[@NilesProductions]

I captured the footage and logged the dates at the end of each day. Looking at my folders of footage it looks like I worked on it a total of eighteen days over the course of a couple months. Some days were just a couple hours others were dawn to dusk.

[@AI-oz6ju]

Excellent video, thanks for sharing. I have a few questions: 1. I like using screws too. Did a fence using screws, but my understanding is that for this kind of built framing nails are preferred due to sheer strength? 2. Shouldn't the top surface of all joists be covered with moisture preventing tape? 3. Cost analysis would have helped a lot in description along with material list. 4. Pretty good foundation, but should there be additional concrete in the middle for this size? Though I am thinking of using concrete block foundation. 5. What would you do differently? Thank in advance to everyone who helps with these questions .

[@NilesProductions]

I'm glad you enjoyed the video. I'm just a DIY guy not a Pro, but from my understanding framing nails do have better sheer strength than most screws. When using metal hangers, like joist hangers and rafter ties It's best to use framing nails or structural screws. Not deck screws like I show in the video. (This point has been made in the comments by a number of professionals) I beef up my raters by adding the big lag screws though so it shouldn't be a problem on my build but i would advise framing nails or structural screws anyplace where a screw head is touching metal hangers. For my foundation I looked up the code for the floor joist spans and found 2x10" joist the span less than 12' was more than fine. In theory if you wanted to add another beam and row of foundation piers you could use smaller/cheaper lumber. There are a ton of different ways to do a foundation. Mine isn't "the end all" it's just the way I decided to do it but I find it works just fine for my needs. I used ground contact pressure treated lumber for my joists so I'm not super worried about rot. With that said it wouldn't of hurt to have used tape on top of the joists. I've provided the material list in the video description and broke the list down into sections. Lumber prices have been all over the place these past couple years so I recommend pricing out materials at your local lumber yard for today's most accurate pricing. A lot of materials could probably be substituted for cheaper material. At the time I built the shed in 2020 it ran me a little over $12k One thing I wish I had done was add a ridged insulation between the floor joist before I fastened down the sub floor. While not impossible to do after the fact from underneath it would have been way easier to do before screwing down the plywood on top. LOL Thanks for the questions. I hope you found inspiration in my build and video. This was the first shed that I ever attempted building. I'm not a pro by any means but I have a saw and a hammer so figured why not give it a go. Good luck on your build. :)

[@DeaconDeacon-st9ph]

Love it!Perfect as a tiny house project :) Well done.

[@NilesProductions]

Glad you liked it 🤙

[@jecilopjp4806]

How did you connect your 2x6 top beam to the 2x4-10' sides on the front wall? Did you use any brackets, or just a 10' as a jack stud then nail into the end of the 2x6 beam? I'm guessing your your side wall and front are only connected by nails since the 10"'s are on the ends. Is that right? I've looked at different ways for doing my own 12x20. I'd really like to know about these connections to the front top extension for the windows. You didn't feature that part.

[@NilesProductions]

Yeah for the sides of the front wall I used the jack studs method and for the windows I used the cripple stud method. I attached the cripple studs to the 2x6 by drilling pockets holes and using structural screws. There are a bunch different ways to do this some may better than the way I did it. You might want to add straps or nails plates to beef things up even more?

[@alejandroperales5424]

Few questions…did you design the structure or hire out to get the plan done for you? Was it a matter of cost to go with pillars vs full on foundation? First time picking up tools or is this what you do for a living, contractor? Final cost?

[@NilesProductions]

Good questions Alejandro. I bought some books and other material on how to build sheds/garages at my local hardware store as well as some simple plans online. I took different design elements from what I found in the book/plans modified them and made my own. For the foundation, the ground is a bit uneven and slightly sloped where I built the shed. I figured it would be less labor intensive to do pier and beam vs trying to level the ground and pour a slab. I also wanted the deck to be slightly raised. The price didn't really factor into the decision. When it comes to tools, I've been a home owner for a couple years and have slowly picked up tools for little projects here and there. I'm not a professional carpenter just a guy with a saw and a hammer that likes to DIY stuff. The final cost was a little over $12k

[@alejandroperales5424]

I *really* appreciate your response! And thanks for all the info as well! Reason I ask is that many “DIYers” that post vids like yours that have “zero” experience turn out to be pro carpenters/contractors and not believable. and the price, WOW!!! Definitely pays off to learn building something like this! I’ve been quoted $40-60k for 20x30….now may look into what you did, learn on my own! Oh, and AMAZING JOB!!! 👍🏽👍🏽👍🏽

[@alejandroperales5424]

And forgot to mention, I can watch and rewatch your video of this build and enjoy it every single time more than the last! 🙌🏽👏🏽🎉

[@NilesProductions]

@@alejandroperales5424 I find watching people build stuff is very soothing/relaxing for some weird reason as well. Who would of thought watching some guy build a shed would be so popular.

[@secretsausage1]

So I tried to build your 12' X 20' but I ended up with a 20' X 12'...WTF BRO? Thanks for the bunk instructions :(

[@NilesProductions]

😂

[@fakepseudonym669]

Things I'd do differently: - Roll the joists on top of girders instead of rim joists on concrete pylons - Double rim joists - Put block lines on joists for rigidity and landing plywood breaks (every 4ft.) - Use construction adhesive on the joists when putting on the subfloor, this is the number 1 reason for callbacks about squeaks in the floor, which this building will have many over time (I swear youtube doesn't know about this) - I like to use frieze (or pressure) blocks instead of hangers for joists, but that's just preference - Use 3/4" OSB tongue and groove ply for subfloor - Used California corners on framed walls - Framed the windows on the door side of the shed correctly (sill plates, trim studs and headers) - Call birds mouth by the correct name (a bird box is a much different thing in framing) - Make my rafter plumb cuts after their installation for maximum straightness of fascia - Installed bird blocking between rafters - Installed Z flashing around the entire roof before rolling the standing seam... that's gonna be an issue - Never heard about not caulking or taping the bottom flanges of windows and have lived in high precip areas, if water is getting in, you have much bigger problems than drainage - Girders/block lines/pressure blocks/double rim joist for lanai as well You asked =) Overall it looks nice and it's a shed, so it'll be fine.

[@arlcrane]

I had to stop watching closely at about 3.5 minutes, when you used deck screws to install the hangers. These screws have good holding power for decking, but they have low sheer strength, which is how you're using them. Hopefully you won't have a future problem, but it's important to use the correct screws for an application. Deck screws should NEVER be used for hangers. I skipped to the end, and it looks like a heck of a shed.

[@NilesProductions]

I’m sure I make a couple mistakes along the way as I’m not a pro. So far it’s holding up 🤞

[@jasonbutler419]

Seriously LOVE this build! Very close to what I'm considering putting up for backyard shop/flex space.

[@NilesProductions]

Thanks Jason Butler! Glad you liked it 😬

[@MilenaKoncar]

So for the outer 20x2x10's for the floor, if i wanna build a 34' long room, do i need to put 1 piece that long? Or can i put 2 pices of 17'? Cause a one 34' piece would be such a problem even maneuvering it.

[@NilesProductions]

There are ways you can join multiple boards together.

[@loduke3905]

I am currently knee deep in my 16x20 cabin/tiny house build. She's around 9' on the back and just shy of 14 up top (technically road legal w cheap permit, and easy for a shed moving co to transport). Very close to the exact same modern design with the shed style roof and awning windows up top. I got lucky on some FB MP buys and scored (4) 54"x36" casement windows for only $250 total. They were brand new low E yadda's, still in plastic wrapping never touched. I ran them on either side of my full glass french doors. Flipped 2 of them horizontal and they're now giant awning style windows. Finally finished my exterior work and wrapped up the little 4ft deck on front. I am now getting to the interior build which is exciting and challenging for a single female build. I just installed a lvl beam to run a 8'x20' loft, it'll be close to 5'6 head height and be used as a bedroom and storage. You did a fantastic job on this build 👏. Everything was so organized and thoroughly planned out, lots of little tricks and tips I picked up from the vid. Nice quality material choices all the way around, no short cuts. She'll last a very long time (much longer than my chap lipped of a mess build 🙄🤦🏼‍♀️). Thanks for sharing this 🙏 and I look forward to seeing what else you have in store. ✌🍻

[@NilesProductions]

Wow, your build sounds pretty cool. Are you making a video? I would love to see it when finished. Link back here with a walkthrough or build video when done :)

[@constructionhacks8162]

Hello, This a great video ! My boyfriend and I built our own home. It's a timber house with a concrete slab built on screw piles foundations. Here's a video on how we built the walls ! Hope you will like it :-D

[@rgbking488]

@@constructionhacks8162 where's the video?

[@frankrobinson5453]

After all the positive comments, I hate to be the hater, but your joist hangers used on the floor joists are grossly undersized. They looked like rated for 2x6, not 2x10. Meanwhile screwing into end grain not the strongest connection either. You will probably never have a problem, but if it were me, would've made the floor a lot stronger. Sorry to be negative Nancy.

[@NilesProductions]

Yeah, that’s one area where I could have done better. I’m still happy with how the project turned out as whole though. I appreciate the feed back it’s how we learn. This was my first shed and if I ever build another one It’ll will only be better because of feedback like this. So no need to say sorry, I don’t take offense 🤙

[@EightNinePreservation]

This was mesmerizing to watch and has bolstered my confidence for an upcoming build I have. Your explanations were really helpful and it was all the perfect balance of informative without being info overload or drawing it out. Thanks! Also. It looks amazing!! Well done.

[@NilesProductions]

Thanks for the kind words. Glad you liked the build and video :)

[@casewhite5048]

I think you have to film it otherwise it doesn’t work

[@NilesProductions]

That’s sound thinking… you are probably right lol @case white

[@str8kronic]

That "shed" would be 2000/month in nyc utilities not included. Lol amazing job...did u buy all materials during pandemic? How much would u say all materials cost you?

[@NilesProductions]

Thanks Anthony G. I built it during the summer of 2020. The materials for the shed and the deck ran me a little over $12k at the time. Prices have been all over the place these past couple years so I’m not sure if it would be more or less if you were to build it today.

[@brendanthegreek]

I am one of North America’s premiere un-handy men, and I thoroughly enjoyed watching this entire video. Congrats on the shed, it looks fantastic.

[@NilesProductions]

Thanks B Williams! Glad you enjoyed the build. I wasn't always "handy" but I feel I get a little better with each project. I find it good to try new things that take you out of your comfort zone sometimes. It has helped me grow as a person and give me confidence to try and do more.

[@bsrcat1]

Sad part is that shed probably cost as much as building a house in 2021 with wood prices what they were 🤣.

[@NilesProductions]

lol

[@J4ckkuz]

Great video. Why shouldn’t you seal the bottom of the window flange? Thermal expansion?

[@NilesProductions]

By not sealing the bottom it allows a place for condensation and water vapor to escape/evaporate. If you seal the bottom it will potentially pool water and rot the framing

[@dallas11573]

So. I’ve been looking at tuff sheds to build a 12x20 almost just like this and they want to charge $18k. I have some building ExP. But not a lot. Roofs are my weak spot. Now that lumber is coming down- I’m seriously considering doing this. Did you go off of any plans?

[@NilesProductions]

I bought a book at Lowes called sheds and decks then looked at a bunch of different sheds before coming up with my own design to suit my needs. All in the shed and deck cost me a little over $12g. This was my first shed build. Like you I had a little bit of experience (mostly from building skateboard ramps LOL) It was a little intimating when I started but I took my time and tried to think things through. I planned things out in stages and purchased material accordingly. I figured if I got the foundation nice and square everything else would come together. I also thought that If I screwed up the foundation I wouldn't be to financially vested that I couldn't walk away from the project. Luckily things went well :) As the build progressed and everything started falling into place I started feeling more confident. Once finished I was really happy with how things turned out and am glad that I stepped out of my comfort zone and decided to build myself.

[@dallas11573]

@@NilesProductions I knew you were a skater!! Had a feeling. Like you. I built a few ramps in my day. I’ve also helped a friend build his house so I have a little ExP. Id love to do this with my 13 year old son. I’m curious how much this project cost. Right now tuffshed will charge $17k for a 12x20 minus the deck and nice siding. I’m competing against a wife who doubts my skills. Lol. But after watching this- I’m like hell yes I can do this. Now I just have to convince her it’s a financially sound decision vs tuff shed.

[@NilesProductions]

Wood prices have been all over the map these past couple years. At the time I built it was a little over $12g for the shed and deck. To get something more accurate to todays prices you can take my material list and get it priced out at your local lumber yard and compare it against Tuff Shed. Some items like the 20’x4”x10” will not be found at Lowes or Home Depot. You’ll have to go to an actual lumber store for material like that. I don’t think Lowes or HD sells standing seam roofing either? I’m sure I used a lot of premium material that you could substitute with cheaper materials to bring the cost down a bit as well. There is no shame in going prefab or with a builder like Tuff Shed but the pride I feel when I look at my shed and what I accomplished makes me glad I decided to do it myself.

[@dallas11573]

@@NilesProductions No buddy...You did it right. In fact one of the first ones i've seen on KZbin that has done it right. Using a standing seam as opposed to just a regular metal roof- you should never get any leaks ever.... I know you probably get a lot of "armchair carpenters" but I have been looking. You have skills.

[@jojohehe3251]

Wow, I would have thought that floor was nowhere near well supported. The two big 6x20 outer rails, with two stringers and four bolts to each joist - I'm amazed that all the vertical force is entrusted to ultimately a few screws. I'd have thought you would need more lumber beneath the joists, with stumps below those.

[@NilesProductions]

Believe it or not it’s plenty strong and up to snuff when it come to our local building codes. 🤙

[@westhavenor9513]

Nicest shed I've seen in a long time! Looks more like a classy tiny home. I want to built a 10' x 12' shed. I think I'll copy your style, if you don't mind.

[@NilesProductions]

Thanks! I’m glad you enjoyed the video. Good luck on your build West Haven 🤙

[@garrettsmith4034]

1) Great video and build. I love that you included a material list. 2) Do I need to be a licensed carpenter to build my own cabin/dwelling or do I just have to meet local building codes? I wish I picked up the trade and it's kicking me in the ass currently having not done so. Thank you in advance for the response if you get to it. Stay well!

[@NilesProductions]

Thanks Garrett, glad you enjoyed the build :) Not sure about your local codes or if you have any HOA rules, but in most cases as the property owner you can get permits and schedule inspections when you build your own stuff as long as your plans and build meet the local codes.

[@thomasschafer7268]

never understood plywood outside! why not inside. outside tyvek is enough. water from inside to outside! german word wasserdampfdiffusionsgefälle. 😅😅 no joke.

[@NilesProductions]

My original plan was to make Japanese style Shou Sugi ban wood siding but I got cold feet. Went with T1-11 as a cheap alternative.

[@victorbenner539]

I've been looking for something for my catering commercial kitchen and outside bbq smokers area. This is close to what I had in mind. Of course I'll need to tweak it some but this is a very good start. Nice video. Have a great day 🌤 😀.

[@NilesProductions]

Thanks Victor! Glad you enjoyed the build/video.

[@mrman5517]

this shed is better constructed, waterproofed, and insulated than the house i rent!

[@NilesProductions]

It’s the first shed I’ve ever built, I’m glad you liked the build Mr. Man 🤙

[@justint8405]

Bro I laughed so fucking hard when you snapped that drill bit. I've been there and I feel your pain 😂😂😂 def subscribing!

[@NilesProductions]

First drill of the day and snap 🤣🤣🤣 Glad you caught that lol Thanks for subscribing World’s Okayest Carpenter!!!

[@xisotopex]

oh wow integrating the deck with the shed this is exactly what I want to try to do.... did you actually attach the deck to the shed foundation or are they two independent structures?

[@NilesProductions]

The deck has it's own foundation but is also attached to the sheds foundation with lag screws through the decks ledger board.

[@ralfbierig]

Wonderful build! I hope you do not mind me asking: What did you approximately pay for the material?

[@NilesProductions]

Glad you enjoyed the build Ralf. At the time of construction it ran me a little over $12k for shed and the deck.

[@garrywade7952]

Hi Niles, Do have printable plans and schematics for this build. Are you selling the plans. Thanks in advance

[@NilesProductions]

Sorry, I don’t have any plans to share or for sale.

[@arthurmann3287]

In my neighborhood I checked with my city and I need a miscellaneous residential permit for a building this size which requires sketched plans and a signed and sealed copy. How would I acquire this? Also the shed build was awesome, great job

[@NilesProductions]

Glad you enjoyed the build. I recommend googling Modern Shed Plans and the size you are trying to build. There are a ton of blueprints online for cheap and sometimes even free that should be sufficient for permitting. You can always try and draw your own but it’s good to start with something pro to make things easier.

[@farvasstache6532]

Nice job. Looks great. Dont sweat the "learning" as you go. You can always add some strength if you need to. OH... and the twangy old school country music sounded like it was straight out of the series Deadwood... awesome show.

[@NilesProductions]

Thanks for the kind words. Glad you enjoyed the build and music @farvasstache6532

[@mrwck1953]

Did you do anything special between the siding and cedar shingles? I'm seeing some folks adding z flashing between two sheets on the horizontal edge (above a 4x8 sheet ).

[@NilesProductions]

Yeah, I used z flashing on top of the plywood sheets on the front between the t1-11 and cedar shingles as well as on the side where I cut the triangle piece of t1-11. I forgot to mention it in my VO but did add it to the material list 🤙