How to calculate the load in slabs and beams? | Load transfer mechanism in building | Civil Tutor

[@markdilannyuykonge330]

I love the way you made your video and how straight forward it was I understand it so easily thanks

[@gopalmalapati1446]

Gentle man, excellent explanation, hats off to you.

[@vishakha-k-5]

Can u please recheck the formula u use for calculating the load due to trapazoidal section on beam.. Load calculated are very large

[@darshanshrestha545]

Your teaching is like academic. I’m enjoying; thank you!! Can you also teach how to calculate load on columns?

[@CivilTutor]

Sure

[@EngineeringTech_Civil]

IS-1200 part-01 all clause of earth work measurement . IS-1200 part-01 के सभी क्लॉज इस वीडियो में ।। kzbin.info/www/bejne/sISnqn5-gMZmrtE

[@jyotiranjanpanda4342]

Awesome explanation

[@clifforddevoe919]

Thank you bro, just freaking thank you😢😢

[@dreampannu2198]

great 🤩 truely said, i love to listening this, but i didn't like this for 1day, in the my 4years of college life 😅😇 thank you for this😍

[@axatrathod]

Awesome sir 👌🏼👌🏼

[@phyohtetkoko929]

Thanks For Teaching Sir

[@mbabazirodney2064]

What does 1-1 mean. Thanks for teaching

[@EngineeringTech_Civil]

Nice video 👍👍👍

[@CivilTutor]

Thank you 👍

[@BRane-mo9wx]

Superb sir

[@ihsanullah6479]

Thanks.how to draw this in which software?

[@ibby3849]

hey how did you work out the area of the cross section it says 0.23 but not sure how you got this

[@travelguide786]

Ok, reminder set

[@gowthamiv4841]

Worth watching..

[@sharmakeabdullahicisman4396]

Sir thank you i wanna how to calculate cantilever slab carreid load and transver to the beam

[@CivilTutor]

Will upload soon

[@AlAl-cr7ig]

Thank you

[@aravindhsuriyak.s6989]

Sir,Calculation can u make it as pdf and send it sir.. It's or all using for further calculations

[@EngineeringTech_Civil]

IS-1200 part-01 all clause of earth work measurement . IS-1200 part-01 के सभी क्लॉज इस वीडियो में ।।👍👍👍 kzbin.info/www/bejne/sISnqn5-gMZmrtE

[@mamteshmishra5609]

​@@EngineeringTech_Civil4:32

[@JPCNtakiyimana]

Great

[@mgovindaraju8034]

Thanks for sharing

[@EngineeringTech_Civil]

IS-1200 part-01 all clause of earth work measurement . IS-1200 part-01 के सभी क्लॉज इस वीडियो में ।।👍👍 kzbin.info/www/bejne/sISnqn5-gMZmrtE

[@suryasekharlagudu4794]

Thank you 🙏

[@CivilTutor]

Welcome!

[@amit95gupta]

THANKS SIR, BUT ONE THING I AM MENTIONING THAT LOAD ON BEAM B6 AND B4 DUE TO BEAM B5 SHOULD BE POINT LOAD,BUT YOU HAVE CONSIDERED AS UDL 33KN/M.

[@engrxiddig]

Good 👍

[@abdulzahiraliyi8675]

my question is, after we calculate loads on the beam can we use this load for column design or de we have to do another calculation using approximate area method for loads on the column ?

[@OGTennyson]

Another calculation will be done

[@dashtyswara3277]

Thanks

[@shaahidebrahim9968]

Thank you sir, tutorial on load transferred to column?

[@CivilTutor]

Will upload soon

[@EngineeringTech_Civil]

IS-1200 part-01 all clause of earth work measurement . IS-1200 part-01 के सभी क्लॉज इस वीडियो में ।। kzbin.info/www/bejne/sISnqn5-gMZmrtE

[@meow0808]

Thanks souch

[@vedprakashthakur9175]

could u pls tell me sir how to get the formula of. load on B1 due toslab S1

[@abdulmonimmohamedali9146]

Actually l want to thank you very much .

[@baberkhan-lt8br]

Load due to B5 on B6 will not be UDL as its one end is resting on B6 so it will apply point load on it there.. isn't it?

[@ibby3849]

hey im a little unsure on something what if the design i have doesnt have beams every side for example my design it has beams only on 2 sides of the inividual structure

[@ibby3849]

for example i have a b2 and a b1 but no beams on b6 and b7

[@SumanDas-ey8ro]

What is 1-1 ? How did you get the value, i.e., (1-1/2.1 = 0.523)??? Please help 🥺

[@CivilTutor]

1 - (1/2.1) = 1 - 0.4761 = 0.523

[@sangwoo218]

How to calculate if i have water load on all area of slab ?

[@engrxiddig]

Please sir make detailing using Autocad

[@balabyekubojohnchristom241]

What is the formula for getting number of bars from area of steel according bs8110 for Fy=410, Fcu= 20, Because BS8110 part 3 doesn't have table for suchcases.

[@joshuasolamo8697]

Hey guys how do you calculate square slab

[@pranotostb]

Good animasi

[@brahmaji0098]

Sir if we design 1st slab .. For the project of like g+5, g+6etc How can we take loads of remaining slabs which is the load transfer to 1 St slab Moreover is this for only for ground floor or g+1 ? Pl explain it sir Thank you

[@CivilTutor]

The example I have shown here is for a single storey frame to give you the basic idea of how load is transferred in a frame.... I will cover up for multiple stories in a separate video.

[@THEONEPERCENTCLUB101]

In minutes 8.06 , the load on B3 due to slab S2 = WLx/2 right but why isnt it 2.5 cause the length in beam B3 has a length of 2.5 m. should i substitute ( WLx/2.5 ) or is there anything else. thanks a lot for all this knowledge i am just a bit confused. thank you and have a great day.

[@theandroidguy6032]

It is one way slab and if the load is example 10kN/m2 The it has to distribute only on two equal beams hence divide by 2

[@dhanbiryadav3124]

कोइ भि घरका सारा लोड, कलम के नम्बर मुताविक भाग लगाकर के निकाल सकते है और नहि?अगर नहि तो कैसे निकाले? please explain me.

[@CivilTutor]

There is an error in the calculation.... You can find the rectified calculation here 👇 drive.google.com/file/d/1X5OFsa0rTTTqMrlf4aTz4SmlJiYIJARi/view?usp=sharing Sorry for the error🙏

[@abdulmonimmohamedali9146]

Go ahead, we are benefit from you very much,thanks.

[@fredthe52]

Yes was an error now is good

[@rajusimmanuel3285]

Kindly the explanation shall be little slow

[@pp238]

The last page calculation of the rectified calculation is again wrong. Again span of B4 (2.37+1.0) does not match with 3.6M of B1

[@CivilTutor]

Span of B4 = 2.37 + 1 + width of B5 (I.e, 0.23m) = 3.6 m

[@pp238]

OK

[@DarvaishBandah]

where did the size of beam and column come from? and do the beams and columns with this size resist the loads u calculated? sir make complete video of loads calculations from roof slab to foundation.

[@sathyabalasundaram1801]

Refer below link kzbin.info/www/bejne/hIeYnGSIn9eDn68

[@ygges3407]

it says "given specifications". So you can find the size of column and beams on the structural plan. But if you are the one designing it you will assume the sizes and solve for the whole design if it will (pass or fail) to carry your loads.

[@sekarramaswamy5111]

Thanks for your design analysis… but the presentation to be modified with conclusions….

[@CivilTutor]

Check out my Compiled PDF 👇👇👇 store.civiltutorofficial.com

[@sohailahmed5039]

In case of slab self wt why do we say (thickness x unit wt) and in case of selt wt of beam we say (area ×unit wt) , why dont we use area x unit wt in case of slab too?

[@fransabram34]

The slab is designed per m², whereas beam design is analised per m

[@nasirafridi6013]

Thank you 💗

[@EngineeringTech_Civil]

IS-1200 part-01 all clause of earth work measurement . IS-1200 part-01 के सभी क्लॉज इस वीडियो में ।। kzbin.info/www/bejne/sISnqn5-gMZmrtE