How to Calibrate Orange Hall Effect Analogs For PS5 and PS4

Calibration Tools:
dualshock-tool...
Hardware-Tester.com/gamepad
Links To Purchase Hall Effects (V3 & V5 Enhanced)
s.click.aliexp...
s.click.aliexp...
My Soldering Station
s.click.aliexp...
Socials:
linktr.ee/layhss

[@DrunkenSquirrel2]

I could never get this kind of low error rate on circularity with my v3 ginfulls, was always a pretty big overshoot even after calibration with dualshock tools. I also manually calibrated with the pinholes to get the overshoot mostly equal on all sides, I think I made things worse manually calibrating before doing the dualshock tools calibration and ended up undoing it. The v5s must be much better then? Do you try to get the magnet perfectly centred, or do any manual calibration at all with these v5s? I wonder if doing one manual click to the left/right would center that under/overshoot.

[@Layhss]

I have not done any manual calibration with the v5s, I was using v3s from march and I was getting pretty much the same results as here. It could be the manual calibration someone else in the hall discord recently was getting overshoot while also manually calibrating, could be a bad pair of analogs though

[@PlayStationMilGrau]

I always get around 15 to 20% on circularity tests. Is this method used to reduce it or is there something physical to adjust after que instalation?

[@Layhss]

Don't need to do anything physical, just all digital now, I've done pretty much all models from v1-v5 they all get under 10 percent circularity, are you doing it with the shell off?

[@PlayStationMilGrau]

@@Layhss Normally I make the adjustment with the needle right after soldering the analogues on the board and do the circulatory test (on the hardwaretester website) without the shell, but even when I put the shell on, I only get between 15 and 20%. This method you use is to correct it and get it down to 5% or do I need to do something first? I'm currently using the V3, but I just bought the V5 version from your description link. Are they much better?

[@Layhss]

@PlayStationMilGrau v5 is made for the software calibration, but they all work fine with it, I used v3 with them for a while and I can't remember the ones in the video may have been v3 I forgot what I said but I know I've used v3 and they were fine on here

[@Layhss]

@PlayStationMilGrau I just install the analogs close the controller then calibrate

[@ghillyboy350]

im clicking "calibrate it to the center" button but its not working so is the "stick range" and other buttons i can only "click the check circularity" button nothing else works pls help

[@Layhss]

Not working how, can you explain what's happening or what it looks like on the tester?

[@ghillyboy350]

@@Layhss like all the buttons are not responding it’s like as if I’m not even clicking them. But I am clicking on the buttons nothing works i thought it was my mouse but the only thing working when I click on it is when I wanna check the circularity. The other options are not responding when I click on them. So I can’t calibrate it

[@Layhss]

Have you tried using ir testing another controller or browser? I'm not really sure on how to fix that issue sorry I haven't had any problems with this tool as of yet

[@ghillyboy350]

@@Layhss I tried testing on ds4 and it works but this particular website isn’t working

[@Layhss]

If it's not working for anything I'd try another browser then. You're using this for hall effects correct?

[@Luke-il6fg]

Hello ...and you must calibrating often this controllers? "I have same purple" and i want to instal halleffect modules and I wondering this modification i worth? after instal and calibration how long controller will work without issues like stick drift ect.??? Thanks for video

[@Layhss]

You only need to do this process once, should stay permanently these controllers won't get drift

[@Luke-il6fg]

@@Layhss perfect. sony ern millions $ because this stick drift isue becose people are lazy and bay nex ....next not repair.

[@JonathanStefford]

I physically used the pinholes to center the sticks as much as possible and then used the tools, but the circularity constantly fails over the left side of the joysticks no matter how many times I do it, is there any way I can fix it?

[@Layhss]

Probably not could be due to the physical calibration, but I've done the calibration on v1 I installed on a controller a year ago with physical calibration, but I have no idea on how to fix that

[@Layhss]

I'd reccomend if you can upgrade or get new v5 to replace the controller with if the issue bothers you but before we weren't even calibrating circularity so in my books it'd be OK but it's up to you

[@JonathanStefford]

@@Layhss I was able to fix the issue by disassembling the controller and do the circularity calibration without the caps, now it is much better. Thanks again and by the way I think I have the v5 modules for the dualshock 4 (the ones with red bits in the middle)

[@Layhss]

V3 and v5 is red In the middle v5 is the different magnet shape for the calibration tool

[@heitachi7882]

Ty bud, nice video

[@marcokappaa]

Hello brother, I repair controllers and I have always used the alps analogs, but I think it is time to offer a permanent solution for stick drift. So can you confirm that with these, the drift can always be fixed? Also one last thing, so I just have to install these and calibrate them as you show in the video? Because in other videos they calibrate them with a needle or they manually calibrate then in a different website. The way you showed looks waaay easier and quicker. Thank you brother

[@Layhss]

They are hall effect analogs technically we don't know the longevity but they should work practically forever without issues, hall technology has been around for some time, there's always possibility of faulty units but so far I've repaired over 1 hundred controllers without issues for over a year

[@Layhss]

And it works with all analogs not just hall effect for this calibration method (ps4 & ps5)

[@marcokappaa]

@Layhss so your saying that on this website I can fix drift also for alps analogs?

[@Layhss]

@marcokappaa the website doesn't fix drift, it's to calibrate analogs that you have replaced In a controller, which is why i reccomend them with the hall effects alps are pretty much useless nowadays when we have better replacements that will last

[@marcokappaa]

@Layhss ohh okay, makes way much more sense ahahha...indeed I just tried to calibrate a drifting controller and it kept drifting, I calibrated a controller which I changed the alps stick and was perfectly centred. Yes I agree with you, alps analogs are finally over, from now I will always install hall effect. The v5 are good? Do you recommend some versions in particular?

[@rnbpl]

should i get these or jun zeng's, or any of those otehr ones that come with that tiny board?

[@Layhss]

no point in the board with this now for ps4 & ps5

[@EternalKrule]

Before I buy this, For the v5 will it work for the ps4 controllers?Like all the calibrations?,if not thank you anyways

[@Layhss]

Ps4 and ps5 only not Xbox, but make sure if you're ordering analogs to get the right model for ps4 and or ps5

[@rolardnb]

Hi, thanks for a video! Can I use that website for the calibration of my V3 Hall effect sticks?

[@Layhss]

Yes, you can it works with all versions technically there is no limit any analog works on the site for ps5 and ps4 I know

[@rolardnb]

@@Layhss Awesome. Thanks for your response. And good luck on KZbin with your channel 🙌

[@Layhss]

Thank you, and No Problem

[@EriRickz]

Can I use v3 or v5 only ? what is the difference between v3 and v5?

[@Layhss]

V5 is made for this calibration method and will give you better circularity results, not the biggest difference but if you're buying analogs it's just best to get v5 as they're the newest and best

[@NicolasSilvaVasault]

my hall effect calibration stopped working for some reason, when i try to do anything, centering or range calibration, it just simply don't care, left joystick works normally

[@Layhss]

Analog stick could be faulty or installed incorrectly had an issue once where a stick would just not calibrate properly if you can try replacing it

[@NicolasSilvaVasault]

@@Layhss it was working weeks ago, i haven't played in quite a while, but i don't think the stick can stop working out of nowhere

[@Layhss]

Happened to one of the controllers I did before, could be faulty install or just a faulty unit, or the calibration software didn't properly place, if you're getting the issue where your controller is going weird with analogs going in the opposite directions of which it's supposed to, try playing around with the calibration, if not just replace the analog that always works for me when I get any annoying problems

[@iiSyX]

I done this and mine works perfectly but it still has a very tiny bit of drift 0 deadzone still,

[@Layhss]

You have the hall effect analogs? And are they the jitter versions?

[@iiSyX]

@@Layhss no they don't jitter, they are the ginfulls, I mean it's not really a problem I like a bit of drift cuz no deift feels like you have a deadzone but yeah

[@Layhss]

@@iiSyX that's odd then if they're the non jitter and they are drifting

[@kevinmoreno8980]

Ty

[@deepeshpoulose8607]

Is that fasgear thunder bolt wire ?

[@Layhss]

No, just a right angle usb c cable

[@deepeshpoulose8607]

Mmm okay brother... ❤

[@pokemonzike6130]

What websites is that on

[@Layhss]

Link is in the description

[@naghale]

thx bro

[@Layhss]

No problem

[@IbrahimG2429]

Apakah ini berbayar untuk webnya?

[@Layhss]

Websites free

[@aznnin3130]

😄