How to change a Rear wheel bearing on HYUNDAI SANTA FÉ CM TUTORIAL | AUTODOC

How to change a Rear wheel bearing / Rear Wheel Bearing Kit / Rear hub Bearing / Rear wheel Hub Bearing on HYUNDAI SANTA FÉ CM TUTORIAL | AUTODOC
Top brands that produce Wheel Bearing: BOSCH, STARK, SACHS, SKF, VAN WEZEL, VALEO, LuK, MAPCO, A.B.S., ATE.
📲 Buying via app is always cheaper than on the website!
❱❱ Install the AutoDoc App - interstitials....
On our website you will find a wide range of auto parts you are interested in: goo.gl/hg9q1R
Wheel Bearing: goo.gl/Wiut54
Wheel Bearing for HYUNDAI: goo.gl/j1sJUi
Wheel Bearing for HYUNDAI SANTA FÉ CM: goo.gl/xs1FXD
HYUNDAI Car parts: goo.gl/JNNV2Y
Mobile Shop: m.autodoc.co.uk
► How to replace engine air filter on HYUNDAI SANTA FÉ CM - • How to change Air Filt...
► How to replace Pollen Filter on HYUNDAI SANTA FÉ CM - • How to change Pollen F...
► How to replace front lower arm on HYUNDAI SANTA FÉ CM - • How to change front lo...
📢 AutoDoc in social media:
Facebook: / autodoc.co.uk
Twitter: / autodoc_berlin
KZbin: / autodocuk
Instagram: / autodoc_autoparts
#autodoc #autodoctutorial
Disclaimer:
This video only contains tips and recommendations that could be helpful when carrying out car repairs or replacing parts. AUTODOC is not liable for any harm, injury or property damage incurred while carrying out repairs or replacements, that are a result of incorrect use or misinterpretation of the provided information. This video is for informational purposes only and does not guarantee achievement of a specific result. The user is personally liable for incorrect use of repair equipment, tools or car parts, in particular, when this use poses the risk of injury. AUTODOC strongly recommends being careful and adhering to the safety rules when doing any repair or replacement. Keep in mind that using low quality auto parts does not guarantee the proper level of road safety.
⚡ AUTODOC CLUB - club.autodoc.c...
Add your car to the AUTODOC CLUB garage and get personal recommendations on repair intervals - club.autodoc.c...
❱❱ Install the AUTODOC CLUB App - club.onelink.m...

[@dmt66]

I didn't lip read him saying MotherF&@^$%@ once! Not even a busted knuckle, bumped forehead, rust in eyes, or dropped bolt! Impressive!

[@JefferyTomkins]

on the tucson you have to take the sway arm half way off to get to the stuipd caliper bracket bolt

[@zenalqien5058]

Dear Autodoc.. have you recorded video how to replace rear wheel bearing for 4WD hyundai Santa Fe CM ?.. tx

[@autodocuk]

Thank you for the feedback! Stay tuned and maybe we will release the video that you are looking for. Best regards, Autodoc.

[@iszrock]

Yes too am interested in the same video as Taqin 1965. I have a 2007 hundi Santa Fe. 4WD. without knowing the difference, is there that much of a difference with the assembly? is this video no sufficient enough?

[@spikey911usa]

autodoc.co.uk Also looking for this video..

[@OurDumpingGround]

me to i also need to watch a video for awd 4wd 2007 santa fe. thanks

[@r.r.4401]

Also looking for video on a 4wd 2008 Santa Fe. Thanks

[@EJSDesign]

I used this video to change my rear wheel bearings on a 2008 Hyundai Veracruz. Made it super easy to do. Although the car drives much, much smoother and quieter, I had the ABS, ESC Off, and AWD lights all come on while test driving. Any ideas why? Thanks again for the great vid.

[@mikemosley8558]

Erik Smith Hey did you figure out the light situation? I'm about to change my rear wheel bearing on my 2008 Hyundai Veracruz as well.

[@autodocuk]

Thank you for the feedback. To determine the cause of the fault you should carry out the computerized vehicle diagnostics. Best Regards, Autodoc.

[@huggrietaz]

too tight?

[@kirkd6285]

when i took out the bearing on my my 2007 veracruz AWD the black sensor stayed with the car and the replacement did not come with it. So i left it in there. did you have that black abs sensor on your replacement bearing like in the video? is yours an AWD?

[@allengilchrist9640]

Do you have a video for removing the rear dust shield on a2010 thanks

[@autodocuk]

Unfortunately, we do not have this video. Please stay tuned with us and follow our new tutorials. AUTODOC

[@emadhanna887]

Hi , that is a great video, I have a 2008 Hyundai Veracruz that I am planning to replace its rear wheel bearings, Do you need to apply grease to the new bearing? Also, in this video there is no mention of the torque applied on the spindle nut? Can you pls advise? Thanks

[@autodocuk]

Thank you for your feedback! New spare parts already come greased. Applying grease is not needed. All torque specs are indicated in the technical documentation on the vehicle maintenance, you can find them out at the official car dealer. Best Regards, Autodoc

[@nathandavis5099]

I'm doing this procedure on the exact same vehicle (08 Veracruz). How did you find the process? Any tips you could share?

[@kennethhatmaker607]

I have a 02 all wheel drive hyundai santa fe need to change left rear axle.

[@autodocuk]

Thank you for choosing us! Our technicians will be more than happy to locate the correct parts for your vehicle, please, send us an e-mail via [e-mail] and we will make sure to get in touch with you shortly. Best Regards, Autodoc Team.

[@paulmartinez9285]

It worked perfectly for my 2017 Except for the lower caliper bolt was a real hum dinger

[@autodocuk]

Thank you, your story will be interesting for us and our viewers.

[@kenmtb]

Great video, however it looks like all the parts just fall off on that car without any rust lock lol

[@autodocuk]

Thank you for the feedback! We hope that our tutorial was helpful for you. Stay tuned and follow our latest updates. Best regards, Autodoc.

[@austindboyd]

What about the AWD version of this vehicle?

[@autodocuk]

Thank you for your feedback. Be sure, that the video showing the four-wheel drive version of this car will be shot and will be available on our channel, watch out Best regards, Autodoc.

[@Spadaraz]

@@autodocuk Any news on the above question 4 wheel drive version ? That is a real headache!

[@rudolftan4243]

Is there a way to repair the bearings instead of replacing them with a new one?

[@autodocuk]

Impossible, only bearing requires only replacement .

[@baljindersinghsidhu3959]

How much torque is needed to tight the axle nut ??

[@autodocuk]

Unfortunately, it is not possible to specify the tightening torque, you can find this information in the technical documentation for the repair of your car.

[@msullivan9565]

Why not do a difficult repair on an AWD left side where the ABS blocks bolts to replace bearing hub and you have to pull axle out and disconnect everything to replace CV axle. Worst job ever with every single bolt frozen solid.

[@autodocuk]

Thank you for your feedback! We appreciate your valuable comment. We will take it into consideration for our next videos. Stay home and stay tuned with us! Best regards, Autodoc team!

[@charleslangjahr2044]

How did you get the wheel speed sensor off , I can’t figure out where to apply pressure for it to disconnect. Thanks

[@autodocuk]

The video shows this at 2.15 minutes. You can find this information with the correct removal/replacement in the technical documentation for car maintenance. AUTODOC

[@kennethhatmaker607]

How to change on all wheel drive

[@autodocuk]

Thank you for your feedback! Please clarify or rephrase your question and our experts will be happy to assist you. Best Regards, Autodoc Team!

[@kennethhatmaker607]

@@autodocuk I have a 02 Hyundai santaFe all wheel drive that needs the left rear axle changed.

[@jennifermaxwell4637]

Great video

[@autodocuk]

Thank you for the feedback! We are glad that our tutorial was useful for you. Best regards, Autodoc.

[@allengilchrist9640]

Was this on a 2010 thanks

[@autodocuk]

On the video of the car 2006 - 2009 release

[@denise4243]

Does a bad wheel bearing make a thumping noise when you drive after coming from a complete stop

[@autodocuk]

Thank you for your feedback! It is absolutely right - the first symptom for wheel bearing wearing is an alien sound. Best regards, Autodoc.

[@jonathanrivera7400]

Hi question what's that sensor that you took out from the back for?

[@autodocuk]

Thank you for your your feedback! This is a wheel turns sensor , it operates for the ABS system. Best regards, Autodoc.

[@zainkhokhar5949]

Its the speed sensor. It sends information to the engine as well as the transmission.

[@muradsevdimaliyev1343]

Hi do you have any videos about replacing rear differential of santa fe ?

[@autodocuk]

Thank you for the feedback! We are currently working on creating a wider range of tutorials including the car you mentioned. Stay tuned and follow our latest updates. Best regards, Autodoc.

[@petsrfun9938]

thanks very much u help me with my kia picanto

[@autodocuk]

Thank you for your nice feedback! We are happy to know that our videos are useful to you. Please Stay tuned with us that not to miss out on the new coming tutorials. Best Regards, Autodoc Team!

[@khaledhabiba9665]

Good video. However i have a question. The guy in the video removed all the breaking components in one peace instead of removing the caliper, then the pads and then the caliper mount. Is that possible? How can you do this without first having issue with the rust and second even if you do not have rust. How do you keep the pads adjusted as they were before removing the whole caliper?

[@autodocuk]

Thank you for your feedback. This video is for information purposes, and it shows the main elements to be replaced. Wear and the complicacy of deinstallation are different for each car. Some cars have a minor wear rate, so there are no problems with the part deinstalling, and some cars. And on other cars the it is hard to deinstall the parts, and you won't do without special tools. Best regards, Autodoc.

[@jonnyibullarenandersson9134]

Yea, its easy when you got the 2wd model... No abs-ring, no axel no nothing in the way. 😄🤣

[@edwinrivera7431]

WHAT ABOUT 4×4.??

[@autodocuk]

Dear Customer. Thank you for contacting us. Please could you clarify your question and we will be able to help you. Best Regards, Autodoc team

[@edwinrivera7431]

@@autodocuk I HAVE THIS VEHICLE, BUT AWD.. I GOT IT REMOVE THE AXLE..

[@kennethhatmaker607]

need to change the axle on all wheel drive

[@johnathanhall6899]

Will this work for 2012?

[@autodocuk]

Thank you for your feedback! In this case we can offer you provide all the information about your car, and we will already select the compatible part. Best regards, Autodoc.

[@Williamcole10]

Could really do without the music

[@mrlinsalata]

Yep, it’s got to go. If you’re going to play music with the video, why this?? 😂

[@voiceinwilderness7]

I like the music.

[@johnaranjo6354]

Guy looks like mario lmfao

[@frankgarcia1511]

How do we know the wheel speed sensor is bad?

[@autodocuk]

Thank you for your comment! A breakdown of the wheel rotation sensor can be recognized through the corresponding signal on the dashboard or using computer diagnostics. Best Regards, Autodoc team.

[@joesmith3145]

wire brush the damn spindle and put some anti seize on it !!!

[@sacariaspiedrasdelrio3371]

Ok..now try it with a car that has not had the same.parts replaced or touched in 20 years..

[@autodocuk]

Thank you for your feedback! The complexity of dismantling depends on the technical condition of the car parts. If the bolts have not been unscrewed for 20 years, we recommend that you contact the service to have a qualified mechanic do

[@harriputkonen1921]

Pikku putsaus ois ollut paikallaan, ennen uuden laakerin asennusta

[@autodocuk]

Thanks for your valuable clarifications, your feedback is very important to us so that we understand how to demonstrate them in more detail in new videos. AUTODOC

[@wallycoughlan7291]

I still do a double take whenever I see someone still using an air-powered impact....

[@autodocuk]

Thank you for your valuable recommendation, we will definitely take it into account when shooting new videos and further replacements of these parts. AUTODOC