Hyundai Tucson wheel bearing replacement (pressed in)

Disclaimer: This youtube channel is intended for informational purposes only. The jobs that you see on these videos are based on my knowledge and experience as a technician. Information provided through this youtube channel is not intended to serve as a substitute for your professional technician/manufacturer.

[@Whyismytacoblue666]

I kept the rie rod, and strut attached and used a manual press, and a slide hammer.. worked pretty good, its that stupid snap ring!! I got it out fairly ez, i just mangled it out, but putting the new one in.. OMG broke 4 pairs of snap ring pliers.. wow

[@hyundaitech]

Nice, i never tried that one.

[@Whyismytacoblue666]

@@hyundaitech i didn’t want to pay for an alignment lol I’m cheap. So i just dropped the ball joint and left the strut and tie rod connected

[@hyundaitech]

@@Whyismytacoblue666 hahah nice you need whats best for you

[@SuperBanana45]

love your vids very informative

[@apprentice-i9l]

Hello, I like your video. Is it necessary to make wheel alignment after replacing rear bearing? Thanks.

[@hyundaitech]

Technically everytime you move something from suspension and steering you need to do alignment, but if alignment not accessible its not end of the world in my opinion, everything should be fine.

[@PitCrewPrecision]

Need to replace the stud bolt on my tucson. Is there an easier way than removing the spindle, replacing the bearing and using a press?

[@hyundaitech]

Is it on the front or rear? Front maybe theres a room that you can just hammer it out depends on the room. And usually theres a slight room to just hammer out the affected stud. But if you are replacing the whole spindle i think thats different situation.

[@PitCrewPrecision]

@@hyundaitech front. I got the old one out by using an angle grinder. But having difficulty putting in the new bolt.

[@hyundaitech]

@@PitCrewPrecision so when installing you need a spacer before you install the nut then you can tightened the nut and the stud will just go in. Check online search wheel stud installer.

[@PitCrewPrecision]

Thank you

[@daniloazuelo3046]

Kabayan ,i have hyundai tucson 2015 gls 2.4. Looking part # of wheel hub bearing left rear

[@hyundaitech]

All wheel drive?

[@daniloazuelo3046]

@@hyundaitech its 2wd

[@hyundaitech]

@@daniloazuelo3046 52730-3S200 but double check with your vin number if that matches. Hope that helps

[@daniloazuelo3046]

@@hyundaitech thanks bro

[@maynardacenas4150]

Sir is hyundai tucson 2009 model a press in hub bearing?

[@hyundaitech]

Yes

[@seamantayo6043]

Sir pwede po malaman ung sukat ng wheel bearing for front wheel po inside and outside diameter po in mm pati ung thickness din po in mm. tia

[@hyundaitech]

Sorry sir, mahirap yan wala kaming spec for that kind of measurement unless may physical bearing ako and then i can measure it. Sorry

[@Bob-zd4od]

Is it recommended to replace the knuckle

[@hyundaitech]

Not really, the knuckle is for life, unless the bearing is stucked for good and then yeah no choice but to have a new knuckle. So far in my experienced never happened yet. Hahha.

[@Bob-zd4od]

@@hyundaitech thanks so much.

[@zachross6832]

Did u use the same spindle

[@hyundaitech]

Yes i use the same, the only new is the bearing and snap ring

[@Marloni.Royalty]

What model and year is that Tucson?

[@hyundaitech]

Its 2011-2016 tucson

[@snlkrd5200]

Hey men where is that you work ???? I’m in New York

[@hyundaitech]

Its in canada man

[@joesrustshop4509]

Did this to my girlfriend's car. I looked into it, and found they have loaded knuckles. For some cars,.......unfortunately not this one. Those would make real quick work out of this.