My antenna was ripped of at a carwash so I thought I'd share the repair. Also I added the driver side grab handle while I had everything apart. Like! Comment! Subscribe!
Пікірлер: 131
@threecrossharley2251 Жыл бұрын
Wel I got it done in 45 min. I used a shoe string and tape. It took a few to get threw. Thanks for the video. Hope I don’t have to do this again!
@dnelzy3035 жыл бұрын
Helped me out for sure! Once I had the dash trim piece off, I tied a shoe string/taped it as well to the side you disconnect under the dash. I could feed it through one side to the other and never have to see exactly where it went, tie and tape the new end on, and pull the string!
@vwspdracer3 ай бұрын
There is an easier way that I discovered when I did this last week on my 2014 Silverado. I could not get the new cable back through the hole as there was too much other stuff in the way that blocked the hole. You have to contort your hand to get into the space where the hole is at. Instead, I ran the new cable through the fender, into a grommet that is just below the door hinge. Slice the grommet for the cable and feed it into the space above the dash. Took about 10 minutes to do, as opposed to over an hour trying to feed the cable through the hole it was meant to go through. Remember to carefully slice off the grommet on the new cable and plug the original hole so you do not get any water intrusion.
@raybrintnall33689 ай бұрын
Amazing work. Inside trim always frightened me, but you work with it quite comfortably.
@dodgers93022 жыл бұрын
Good video. Just an FYI - it’s a good idea to replace the cabin filter located behind the bottom half of the glove box if you’re removing it. It’s behind the honey comb looking panel. People don’t realize it’s there and it gets really dirty and should be replaced every 3 or 4 years.
@russell_poppi Жыл бұрын
Lol. I came to find out what I had to do to replace my antenna. At the 5:13 mark, you just kinda through it out there, just unscrew it. I wasn't sure, so thanks for adding that 5 second bit of important info 😉👍
@mikehunter43175 жыл бұрын
Well I finally succeeded in getting the cable thru the firewall, took alot of screwing around with an inspection camera and wrapping yellow electrical tape around the cable in order to see where it comes from along with a few other tricks to make it work thx for the original video
@vincentlopez84065 жыл бұрын
I'm glad you were able to make it happen bud.
@Elevated_dan3 жыл бұрын
My cord broke that I ha tied to my antenna wire so now I’m onto just trying to feed it through the firewall. Any tips I have no idea where the wire goes once it’s pushed through that hole on the side of the firewall.
@markgarcia34894 жыл бұрын
Thanks for the video saved me a bunch of looking around to find it.
@vincentlopez84064 жыл бұрын
Im glad i could help
@joseclaudio90514 жыл бұрын
Remove the top dash with speaker coger and side andle covers tie a wire really tight to the old antera and pull it out, now tie the new antena and pull it in😉 you're welcome.....no need to remove glove boxes or fuse cover
@isokane97262 жыл бұрын
You just blow my mind. Way more simpler.. just laughed 🤣😭.
@HewHolden Жыл бұрын
Zip ties should do better
@robertmees6790Ай бұрын
From the looks of it it is a spliced connector that doesn't go all the way to the radio correct are you there
@andrewkoszuth9562 жыл бұрын
Great video, a lot of extra work but I think you were learning as you go. Good comments section!
@connorsavage24523 жыл бұрын
Awesome instructional video. Much appreciated.
@1SikkHd143 жыл бұрын
What’s the black thing called he pulled out from the antenna base?
@JohnWargo935 жыл бұрын
Good video man!! Very informative!! Like the new antenna too!! Keep up the content!!
@vincentlopez84065 жыл бұрын
Thanks. Planning to put out more content soon.
@brianboomhower16632 жыл бұрын
Good Video. I tied mine and came apart when pulling thru. Spent TOO much time trying to send cable thru from firewall side-felt it stop, like hitting the heater box but could never find it or see it. I ended up removing grommet from under upper door hinge and sending the cable thru that way. Can see it and grab it thru the body opening where the wiring goes thru. The grommet on the new cable it the same size as the grommet I removed under the hinge so it seals. The grommet I removed plugged the factory cable hole(firewall side). Hope this method eases someone elses pain.
@benjaminalvarez15114 ай бұрын
Hey brainboomhower1663 what did you end up doing with the original hole ? Did you plug it in?
@brianboomhower16634 ай бұрын
@@benjaminalvarez1511 yes I belive I plugged it with a grommet
@shawn.ski35315 жыл бұрын
Thanks for the video!
@MrLngboarder75Ай бұрын
This is the job I needed to do today. Pops snapped his off on accident.
@bwthreadgill7 ай бұрын
Great video! Thanks for the help!
@bizzie1622 жыл бұрын
Great video. Millennium Chevrolet in Hempstead claimed it was a $1400/10 hour job. I'm embarrassed for them.
@christopherengel12754 жыл бұрын
Lol....Thanks for the video Vincent.. I'm laughing because I just purchased a truck cover for my 2018 Silverado that "Did Not" come with any antenna hole fitting. So rather than taking a guess as to where to pop the hole (risking the hole being off center causing the cover to be applied lopsided), I figured let me go online and see how difficult it would be removing the antenna first. Well, 4 1/2 minutes into the video I'm thinking to myself, yeah this isn't going to happen. Just give me the Damn scissors, I'll cut the hole n hope for the best! Then, 5 min n 12 sec in to the video I hear, Oh n BTW, if it's just the antenna you're replacing, you can always just screw unscrew it!!!!.... I was like "WHEW" that was a close call!!!......lol....... Thanks Vincent!...👍
@vincentlopez84064 жыл бұрын
Lol well i glad you enjoyed. It.
@mikehunter13455 жыл бұрын
I gave up buddy, its going into a stereo shop I could only get it to come out on the drivers side of the blower assembly. Sound is insulation seems to be in the way. I might have one more crack at it but I really do not want to cut it out but i might do it I will let u know
@unathandavis Жыл бұрын
Thats alot of work. The antenna is super tight on my 2018 sierra. Now I'm scared to break it then I gotta go through all this to replace the base!😬😬😬😬
@johnbustamante465 Жыл бұрын
Mine is super tight on my 2009 silverado cant get it off, were u able to get your attenna off?
@maxpavlis19493 жыл бұрын
I got the cable unclipped from the top of the dashboard, but when I go to pull it out from the front in the hood, the cable won’t budge. Is it attached in another spot or should I just yank on it?
@chiphester78313 жыл бұрын
Hiw well does the antenna work? I bought one but also have to replace my antenna base first.
@CACK_-rg6ln2 жыл бұрын
if you could make a simple video on how you removed the orignal antenna from the out side, thats all i need. im trying to install a bullet like urs . for that to happen do i need to go inside and take everything aprt like you did or can i just remove the old antenna and then put on the bullet
@juanvalles69192 жыл бұрын
how did you feed it though the hole from the outside ??? because i’m have problem feeding it through
@truckingoover2 жыл бұрын
I ended up pulling RF fender …if that grommet does not seat or the loops are not back on correctly could make a water leak
@larrydockery12432 жыл бұрын
Does the antenna go straight down r do u keep pushing until u see it I’m Having hard time trying to get down
@Elevated_dan3 жыл бұрын
After having my lead break I now have to feed it in from the engine side of the firewall. Once it goes through the hole where does the antenna go? I had all of it in but didn’t see it on the inside of the cab. Also got stuck after I fed it through so I’m worried that’ll happen again. It was stuck for a few hours wrestling with it and getting hand cramps. Anyone have any tips
@chainsaw720813 жыл бұрын
Hey, I was trying to replace my antenna with a bullet just like you are doing and I broke the screw off on the inside! Are the threads reversed or was mine just rusted on?
@jkrish48454 жыл бұрын
What is that part you first removed called?
@lancefravel10924 жыл бұрын
Wow just went through this nightmare of a task. Not sure if the blower is larger in a 2500 or what but when I took the lower piece off below glove box there is no way to see the hole through the firewall behind it. Can barley get a finger behind there.
@lancefravel10924 жыл бұрын
Did use some wire and had it pulled through but came off when pulling new cable in. Glad if did tho because had I kept pulling it prob would have ripped the cable anyway.
@vincentlopez84064 жыл бұрын
Im glad you were able to complete it. It was rough for me too.
@g00dfeller3 жыл бұрын
Man I am having trouble getting this cable through I don’t see it coming out where the grommit locks in or should I use a different hole. And should I start on the under hood side and then go to the dash side last?
@vincentlopez84063 жыл бұрын
Yes it was hiding under the dash I had to use some lights to look for it
@davidfreese2592 жыл бұрын
can u just order the piece with the three bolts? instead of it with coming with the wire i can’t find it at all help anyone ?
@damianwilliams14232 жыл бұрын
So I have a question, I've been trying to install my bullet antenna but I can't figure out how to remove the screw that the factory antenna sits on because the bullet antenna that I brought doesn't fit on the factory screw nor did it come with any direction's it did come with some adapters but I have no idea on how to remove the factory one have a 2015 gmc Sierra
@vincentlopez84062 жыл бұрын
You have to use an adapter
@AZBoy815 жыл бұрын
I have a 2013 with the same exact issue. I have no clue how I'm going to reach where the new cable makes it to and through the fire wall. 😭
@vincentlopez84065 жыл бұрын
Lol I took me like 15 min trying to find the cable under the dash. But if you look under with a flashlight and have some one push in and out just a few inches. You should see it move.
@dnelzy3035 жыл бұрын
Brian Klein I just finished doing this with my truck, same body style as you. Once you have the upper dash trim piece off, tie a shoe string or some kind of sting string to the end you pull from the dash. Pull it out once you have that rubber piece through the hole, pull until it comes out. Take off the tape, tie a new knot, retape, and pull back through into the truck, making sure the taped part was fed through the part the rubber thing stops at. Hopefully that makes sense!
@HewHolden Жыл бұрын
Do not just pull on it mine just ripped apart so that’s great. Any idea where exactly it goes through the firewall? I can’t seem to feel anything
@johndeesfpv9289 Жыл бұрын
I'm putting the stock antenna back on, the bullet looks cool but don't pick up very good
@DavidRoyMusic5 жыл бұрын
Can you add the link to the trim removal kit you have here? My antenna snapped off in the car wash and I have to do this. My parts are coming in soon, just need the trim removal kit
@vincentlopez84065 жыл бұрын
I'll look for it. I just found the cheapest on Amazon prime.
@josegarza47864 жыл бұрын
question: can you just change out the male/male screw on the base instead of going thru that whole process?
@vincentlopez84064 жыл бұрын
This is how to change the male part out. I wish it were easier but its not
@josegarza47864 жыл бұрын
@@vincentlopez8406 ty
@mikehunter13455 жыл бұрын
I haven’t continued for a couple of days, been working and its been real cold here I will be trying again on Tuesday when im off for a couple of days. I will let you know then
@vincentlopez84065 жыл бұрын
I'm sorry you're having a hard time. I hope you can figure it out.
@vincentlopez84065 жыл бұрын
How did it gom
@vincentlopez84065 жыл бұрын
?
@mikehunter13455 жыл бұрын
When you said you removed insulation a fee times, did you cut it out then replace it ? That stuff seems to be the only thing stopping me I really don’t know how far up the firewall it goes
@vincentlopez84065 жыл бұрын
Which insulation?
@vincentlopez84065 жыл бұрын
You mean the one from engine bay?
@mikehunter13455 жыл бұрын
Passenger floor behind blower fan Ive done alot of work on many vehicles and this is by far the worst
@vincentlopez84065 жыл бұрын
I didn't have to remove any insulation. When I removed the plastic piece at the bottom. The cord was there. I look for it. But I was able to find it
@natebissell215 жыл бұрын
I have the entire cable up to the rubber grommet installed and I can’t find the cable inside the cab. I think I am going to try putting the entire antenna base under the dash and see if I get reception. I only use XM but not working how it should is driving me crazy
@Ray000693 жыл бұрын
Ah fuck me! I broke my antena. Now I need to replace it. Thanks for the video.
@vincentlopez84063 жыл бұрын
Glad I could help
@franciscoruiz8103 жыл бұрын
Can you send me the link to the antenna base I don’t want to order the wrong one I have a 2017 Silverado
@vincentlopez84063 жыл бұрын
They don’t sell it any more I tried to find it on Amazon but it says unavailable
@Eric-27205 жыл бұрын
Wondering if you're still replaying on here. If, so, it looks as though you only needed to take off the glove boxes, bezel and side end piece? Also How hard was it to run the new cable from the base into the cab itself?
@vincentlopez84065 жыл бұрын
Yes that's all you have to take off. I was just removing everything that I thought was in the way butit wasnt actually that much that was needed. But it wasnt hard. It took a little frustration. But I was able to get it done.
@Eric-27205 жыл бұрын
@@vincentlopez8406 Thank you for the replay!!!! I have been told that you need to remove the front fender as well.
@vincentlopez84065 жыл бұрын
No you dont have to. I didn't remove it and I was fine
@Eric-27205 жыл бұрын
@@vincentlopez8406 Awesome, I may be back asking a question or two if I attempt it myself. Thanks for the replys!!!!
@vincentlopez84065 жыл бұрын
For sure, good luck !
@josephpresti37603 жыл бұрын
How is your reception with the bullet antenna?
@vincentlopez84063 жыл бұрын
I had zero issues. But honestly I mainly streamed music from my phone. But when I used the regular radio i had no issues
@sarahlambert9143 Жыл бұрын
Exactly what just happened to mine
@mikehunter43175 жыл бұрын
I just had the exact thing happen, string came off. how exactly did you get the wire back through the firewall ??? To start it, you push in through the hole, from passenger side towards drivers side, then it seems like it has to made a 90 towards the interior of the vehicle
@vincentlopez84065 жыл бұрын
When you push it down. It should come out closer to the passenger side. If you go under with a flashlight you will see it and have a friend move it in and out about 1/2 and inch and you'll see it move
@mikehunter43175 жыл бұрын
@@vincentlopez8406 When you say"push down" do you mean down towards the ground ? I have alot of sound deadening material on the firewall behind the blower assembly. Did you have that to fight with as well ? I've looked closely at several different videos and the cable looks like it possibly feeds through the passenger side of the firewall not directly behind blower fan I really do not want to have to remove my whole dash just to feed this through
@vincentlopez84065 жыл бұрын
I did. I had to pull it out and put it back in like 3 times
@mikehunter43175 жыл бұрын
@@vincentlopez8406 This is absoulutley the worst thing by far that i have worked on Something that should be so simple turns out to be the hardest Love to know why GM made the blower assembly all 1 piece instead of being able to remove the cabin filter box seperatley oh well, I'll just keep fighting with it Next step is to remove all sound material one way or another
@vincentlopez84065 жыл бұрын
Do you have the same year truck?
@Roombacare3 жыл бұрын
I just need to take the antenna off. Is it just unscrew?
@vincentlopez84063 жыл бұрын
Yes It just loosens up with a wrench
@Roombacare3 жыл бұрын
@@vincentlopez8406 thanks for the quick reply Vincent
@vincentlopez84063 жыл бұрын
No problem
@RafaelRodriguez-xe4fe3 жыл бұрын
How did you get that rubber boot out
@vincentlopez84063 жыл бұрын
I can when I pulled the cable
@RafaelRodriguez-xe4fe3 жыл бұрын
@@vincentlopez8406 everything on the video you posted was on the money the only thing is that boot theres no room to pull it out
@natethomson66892 жыл бұрын
"I put my finger in this little hole.. haha" 😅
@Red26842 жыл бұрын
How the hell did u get the grommet in?
@vincentlopez84062 жыл бұрын
Lol a lot a frustration
@Red26842 жыл бұрын
@@vincentlopez8406 any tools help or just pulling the cable?
@ezurmnd3 жыл бұрын
Do you have a link where you get it
@vincentlopez84063 жыл бұрын
What part?
@ezurmnd3 жыл бұрын
@@vincentlopez8406 the antenna
@vincentlopez84063 жыл бұрын
I looked for the antenna but they don’t sell it anymore
@vincentlopez84063 жыл бұрын
Sorry
@dennislepowsky48093 ай бұрын
Way too much work for an antenna. Tried to remove my antenna today and it just spins, wont come loose. I’ll just leave it and bend it back every time i go through the car wash.
@piemoon24883 жыл бұрын
No wonder the dealership said 3 hours of labor = $500. Plus a 30 dollar part.
@palomamota88303 жыл бұрын
Lmao I did the same! Stupid car wash! 🤣🤣
@vincentlopez84063 жыл бұрын
Lesson learned lol
@palomamota88303 жыл бұрын
@@vincentlopez8406 true! I haven't fix mine! 🤦♀️
@terryhowell83362 жыл бұрын
Good video but you completely left out the grommet & firewall. Very important part smh
@vincentlopez84062 жыл бұрын
It’s in the video
@wesleyjones55914 жыл бұрын
Yeah screw that cheaper and easier for me to drill it and re tread it with a tap
@vincentlopez84063 жыл бұрын
If I had the tools for that I definitely would have
@jeffmoreland69572 жыл бұрын
Don’t take all this apart. Just unplug the wire from the base that has the three screws. 2 minutes max!
@vincentlopez84062 жыл бұрын
It’s one cable that runs through the firewall
@johndemarche25912 жыл бұрын
Is the antenna cable removable from the base? Is so buy a new bas/cable and swap the base only. Makes sense?
@vincentlopez84062 жыл бұрын
When the drive through car wash bro the antenna it also damaged the base
@Montana2strokers2 жыл бұрын
Genius comment. My antenna wouldn't un screw so I bought the whole assembly thinking I was gonna have to go through all of this for just a base. Pulled new wire from new base and it came right out. Now I'm gonna remove old base with stuck antenna unplug wire and plug into new base. Minutes instead of hours.
@kirkwhite50214 жыл бұрын
It has to be an easier way to replace the antenna base..
@vincentlopez84064 жыл бұрын
If you watch the end. I short cut some stuff. But it is that difficult. If you find an easier way please comment so i can pin it for anyone who needs it
@gregsalter935011 ай бұрын
What the fuck am I watching! Dude my ram. All you do is twist off the Antenna and twist a new one on!!! Ram for the win
@TooDrunkHD Жыл бұрын
Fucking drama just for the antenna.
@calebjackson65442 жыл бұрын
this is impossible
@rustyallen8582 жыл бұрын
This is stupid. You don’t show the actual replacement of the antenna!!