In this video, we will learn how to change brake rotors and brake pads on your car. It is not as hard as you think. Hope you enjoy! Special tool for compressing brake pistons: www.amazon.com...
Пікірлер: 25
@robobertelliclark98825 күн бұрын
Very good video and good to show the potential problems, but ideally use a dial gauge after fitting the new rotor to check for run-out. Rotate the rotor between all possible fitting positions to choose the minimum run-out. Obviously the hub mating face also needs to be totally clean so it’s wise to use a wire brush before fitting the rotor. Doing this prevents brake vibration. For those without a dial gauge and magnetic mount the workaround is to remove and refit the rotor to the next position if there’s vibration, and that might need to be repeated four times to get the best setting. But you need to be sure which rotor/rotors are causing the vibration. New rotors need to be thoroughly cleaned using brake cleaner to remove protective oil/lacquer film, but not if using coated rotors.
@henzolo3 ай бұрын
very good. I use the bar from my jack as a breaker bar.
@tonystubbs9189 Жыл бұрын
Tip: the loose tire under the car is a good idea as a back up for sure but it needs to be up closer the front where you're working. It doesnt really do anything next to a tire supporting the car.
@onlya4cyl95211 ай бұрын
Got it!
@jimjackson4256Ай бұрын
What about the rear brakes . any video about them?
@yanli4422 жыл бұрын
yea lot of time it's hard to do it first run, it gets easier. Great video!
@onlya4cyl9522 жыл бұрын
Thank you!
@RedURs63 ай бұрын
Do you remember the exact size of the M8 Bolt? Thanks!
@lucasaliba2 жыл бұрын
Nice video and well described. Thanks for it
@onlya4cyl9522 жыл бұрын
I’m glad it helped!
@jareksa12 жыл бұрын
You should still check the brake fluid level in the reservoir because when you pull back the brake pistons, the fluid level in the reservoir must have increased.
@onlya4cyl9522 жыл бұрын
You are correct my friend. One of the steps I took was to open up the cap on the brake fluid reservoir so that I could keep an eye on the fluid level as well as any significant air bubbles.
@dracarnoir76062 жыл бұрын
Great job keep doing the videos .
@onlya4cyl9522 жыл бұрын
Thanks!
@jiv779 Жыл бұрын
couldnt you just pull the red battery tabb for battery part?
@jareksa12 жыл бұрын
Dobra robota ;)
@onlya4cyl9522 жыл бұрын
Thanks!
@nachos4018 Жыл бұрын
Question, where did you get the front license plate holder?
@onlya4cyl952 Жыл бұрын
I got it from Amazon. Just search up tow hook license plate mount for your specific car👍
@gianederick1220 Жыл бұрын
how much did the parts cost? roughly an estimate for all four wheels?
@onlya4cyl952 Жыл бұрын
I would say around $400 for all four wheels.
@13skoobs Жыл бұрын
Why do u disconnect battery before ?
@onlya4cyl952 Жыл бұрын
It’s always good practice to disconnect battery when you work on a car. For my specific car, there were people saying that the brake piston would compress if the key is near the car so I just disconnected the battery. Some cars will freak out if you disconnect the battery because it’ll reset the ecu meaning the car will need to relearn everything.