How to change Infiniti G37/Q60 7AT Valve Body

[@markzinchuk]

Hey guys! I just wanted to follow up after the video and say that putting in the remanufactured valve body did not work, and it would need programming. What I ended up doing is taking a valve body off of another G37 that is used and put it in and it fixed my issue without any programming necessary!

[@kxithdifferent2123]

Hey so I have a 06 g35 sedan and I just bought the same transmission and the same model and trim the 5 speed automatic for like 130 off a dude it got 140,000 miles on it instead of replacing the whole transmission I just want to replace the valve body because I got the front brake solenoid code so if I take the one out the new transmission I got and put it in my car will it work and wouldn’t need programming

[@markzinchuk]

Hey, from my experience, I was able to take a used valve body off of another G37 with the same trim and transmission as mine and it fixed my issue without any programming . I would think that it would work for you as well. I don’t want to mislead you or say something for sure, I just want to tell you from my experience that it did work, so I guess take it as you see fit!

[@kxithdifferent2123]

@@markzinchuk so when you finish did you reset the code itself and the check engine light went away?

[@markzinchuk]

@@kxithdifferent2123 Yes, when I finished, the lights went away

[@kxithdifferent2123]

@@markzinchuk ok I did it all and when I tried to turn the car on it say 3rd gear instead of park and it won’t turn on

[@TrinityParaziader]

I see a lot of people asking about reprogramming the TCM when it is installed- the answer is No. I just replaced mine in my 2016 Q50 with the 3.0t. I bought a new TCM/valve body from Infinity for $2200. The reason I didn't buy a refurbished one off EBay or Amazon was because they all said the country of manufacture is China. Also, if you look at the sellers reviews, most were full of complaints from unhappy people. I did the work myself pretty much how the guy in this video did it. I bought a bunch of cheap hand tools from Harbor Freight and then rented a jack and jack stands from ACE. But here's the thing, ACE charges a daily rental fee, but if you rent on a Friday and return on Monday, it is only a one day rental charge which is good. It took me all weekend to do it because I followed each step precisely that I got off a Q50 forum. I filled mine a little differently. On the passenger side of the transmission is a filler hole that is capped off. It is where the dipstick would go on most cars. So I filled it through there and took off that little plug on the pan and waited for fluid to drip out of there when it was full. I put the plugs back in and started the car for a minute and shut it off. I then checked and added more fluid the same way. But here is the thing, even though it doesn't need to be programmed, it still has to go through a learning curve. It shifts all funky until it is driven awhile. I had to slowly accelerate and decelerate until the shifting got itself figured out. After about a day it was like a new transmission

[@markzinchuk]

@@TrinityParaziader thanks for the information and letting other people know!

[@TrinityParaziader]

@@markzinchuk Sure. No problem. I got a lot of my information off Q50 forums. So I had a code for P0720 and so I changed the speed sensor. That took me a long time because I had to pull the exhaust and the back of the transmission to change it. It was 115° outside all weekend (I live in Nevada). After all that it didn’t fix it. I was so bummed. I joined some Q50 forums and saw how many people had that same problem and they replaced their TCM. One guy uploaded the factory Infinity transmission manual. So I printed that to learn how to replace the valve body. So that was cool to have. But it takes me way longer than most people because I follow each step to a tee. But I think anyone can do it themselves. There is no reason to pay a dealer to do it.

[@markzinchuk]

@@TrinityParaziader Yeah I definitely agree I had to do mine twice since the reman in the video didn’t work but I swapped in the used one and it worked. I did it with 2 jack stands in my driveway. Wasn’t too fun, but definitely through some determination possible! Dealerships definitely is too expensive. Doing it yourself is part of the experience too lol!

[@l3gacy430]

​​@@TrinityParaziader @TrinityParaziador glad to hear you didn't have to reprogram, when you purchased did you have to provide infiniti with your VIN? I heard they may program it for you with that when you do, but no sure how true that is Also how many miles is your 3.0 and how much was the rental in total? I have 2 Jack stands but not sure if I needed 4

[@TrinityParaziader]

@@l3gacy430 Okay yes I did have to give them my VIN to buy it from Infinity but they had it in stock. I know that no one programmed it because everything was sealed as tight as a drum. The parts guy went to the back and pulled it off the shelf and handed it to me. Its wrapped in cloth, and sealed inside two bags and then packed into a box. So the jack and jackstand rental was $75 a day. But here’s the thing, if you rent them on a Friday and return them on Monday it is only a one day rental. That’s the way to go. My car has 47,800 miles on it. So that seems early for the TCM to go out but the way I see it, the car is paid for. Its 8 years old and that’s the only thing that has gone wrong. It’s cheaper than a monthly car payment so that makes it easier for me to justify spending that kind of money to fix it

[@khalilwhitney392]

we’re all having the same problem and it hurts 😭😓

[@markzinchuk]

Yeah man it’s pain😖. Infiniti definitely should’ve done a recall on this. I’m going to be swapping in a used valve body from a junkyard rather than the remanufactured one on eBay that I did in the video. I will do an update on my Insta and KZbin if that fixes the car!

[@markzinchuk]

Hello! I see you commented on my video about two weeks ago, saying that you have the same issue. After swapping in the remanufactured one, it did not work. But, this past week, I was able to finally find a parts car and pull off an entire valve body Off of another G37 With around 100 K miles. I just swapped it in and it fixed the issue! Shifts smoothly and threw all the gears! No reprogramming or anything needed to be done. So I think if you just go buy a used one off of a junkyard, or somebody else like a car, it’ll work!

[@COSMICO321]

​@@markzinchuk I have a 2009 infiniti g37 sport. Can I change it from a 2008 infinity g37 sport?

[@markzinchuk]

@@COSMICO321 I just looked on Google and your 2009 has the 7 speed already, and the 2008 still has the 5 speed, so I believe from my understanding that would not work. You would have to go with a 2009 or newer for the 7 speed.

[@markzinchuk]

If you would, like, you could do more research to see if it would work, but from my understanding, you would have to have one with the same speed transmission. Maybe I’m wrong, but that’s from my understanding.

[@Notoriousahmed]

All together at a dealership this is a 2500 job. I bought my q50 and the day i took it out the lot after about 30 mins the valve body shout out on me. Very lucky i had 1000 mile warranty and i just took the car out. Car took abt the week to get fixed but now everything is good. Maintenance is key with infinity, especially things like fluid, spark plugs, coils, rear diff fluid. Also OIL changes before 5k miles!!

[@onieshianapoleon2547]

I do my oil changes every 5k miles and you recommend doing it earlier?

[@Notoriousahmed]

@@onieshianapoleon2547 yes 100% , i do every 3.5-4k miles

[@onieshianapoleon2547]

@@Notoriousahmed what yr is your car?

[@onieshianapoleon2547]

I had a 1995 that I did the old school way 3k. But my 2014 I did every 5k

[@Notoriousahmed]

@@onieshianapoleon2547 yeah nah bro, trust me , do the oil changes early , your engine will thank you. How many miles on your 14??

[@riversrestoration]

man, just bought a remanufactured one coming pre programmed, praying it works

[@markzinchuk]

Hope it works for you too! Probably since mine wasn’t programmed that’s why it didn’t work, but I hope for you it will being already programmed

[@Deritot-eyb_and_lleweraf]

Where did you buy yours and for how much?

[@stanleyjacobs851]

I have a 2008 infinity fx35 s u v that needs a valve body where can I get one that will work for it with out paying a arm and a leg for it and to do it is it the same process on a s u v as is in the video?

[@markzinchuk]

@@stanleyjacobs851 hi, I ended up buying a used one and putting it in there and it worked great without any problems and it only cost me $100 off of a friend. I would see if any used cars or junkyards would have them because that would probably be the best option pricewise. I’m guessing the process wouldn’t be too much different, but I would look to make sure!

[@seanmitchell7532]

you had me until you said you didn't understand the transmission fluid fill process then developed you're own method which probably added too much the fill hole is a self limiting fill hole/internal dipstick, it extends to just the right height inside the trans when level that the correct amount of fluid stays in an excess comes out, assuming you haven't somehow excessively drained the trans, the running of the vehicle for a moment then refilling is to ensure fluid has made it into every nook and cranny insuring the self limiting fill hole works as intended

[@markzinchuk]

Hi, yes at the time I was confused on the fill up process. After researching and watching other videos, I figured out the whole process and the steam and all that. I ended up putting too much in them took some out. Now I’m at the correct level! Thanks for the feedback!

[@Motion556]

Ipt upgrades the original one for more power and reliability but you have to send it off and it’ll take a while b4 you get it running

[@l3gacy430]

How much do they charge?

[@torvarrisevans9334]

Nice bro, I have this same issue in my vr 30 red sport am experiencing, can I use the valve from a 3.7 7speed in my red sport .

[@rizwanshafaat5394]

So basically what you saying is basically I buy a valve body and basically change it and it should work basically 😊

[@markzinchuk]

Hey, that’s what I ended up doing but I put a remanufactured one in there and it didn’t work. But I’ve had people tell me that if you buy one from another G37 that is Used that I will work. I’m currently working on that now and recently bought a used valve body and hoping to get it done this week.

[@markzinchuk]

Hello, I see you commented a few days ago on my video and I said that I put in the remanufactured valve body as shown in the video. This week I ended up finding a parts car, another G 37 with around 100 K miles, took it out and swapped that valve entirely into mine. No reprogramming or coding needed to be done, and it fixed the issue! Shifts through all of the gears smoothly. basically if you find another valve body off of another one that works, and even being used, it works. Hope this helps!

[@Motion556]

Have the original one upgraded by ipt trans or you’ll have to reprogram it if you get a new one

[@sklizzy3125]

Basically yea basically

[@jessebarnes6720]

I’m having the same issue as you on my 2015 Infiniti Q50, AWD, Premium. Check engine light is on, throwing code P0720 “output shaft speed sensor”. I’ve seen another video of someone removing the tail section of the transmission to access the actual sensor. Seems like by changing the valve body that maybe the output speed sensor was not faulty on yours?

[@markzinchuk]

Hey! Yeah unfortunately we’re having this issue, but I hope I can help with this… when I had the issue, it was also throwing a PO720 code as well. I had the same output, speed sensor code as you. I put in the remanufactured valve from eBay, but that actually didn’t fix anything. What I ended up doing was finding another G37 that was used with around 100K miles, and put that valve body into mine. No reprogramming or anything needed, and it fixed the car perfectly!

[@steviesawney-pc3lb]

go for the valve body same thing happened to me I change the sensor nope same code came back

[@RichardCheny]

Got a P0720 code in my ‘15 Q40 and won’t shift past 3rd gear. Bought an OEM valve body from Infiniti and installing it myself this Saturday. Wish me luck I’ll let you know how it goes.

[@markzinchuk]

Good luck man! I hope it works for you!

[@levilee6488]

How much did they charge you? My 2015 Q70L just done this same thing 2 days ago

[@markzinchuk]

@levilee6488 I ended up buying the used valve body for around $100 off of a friend. I did the replacement and fluid change and everything myself in the driveway lol. Not fun but saves money.

[@corymontano2661]

Did it work

[@markzinchuk]

The remanufactured, one that you see in the video did not work. I just bought a used valve body off of another G37 and it fixed the issue without any programming or anything

[@jonathanlay2005]

my 370z started having an issue where it wouldn’t shift past 3rd gear and it doesn’t display the what gear it’s in, like 1st 2nd or 3rd. the car was used a lot in the manual mode. do you think the speed sensor is fried and need a new valve body or could it be that the headers are bolted on wrong and doesn’t have an o2 sensor

[@lostjester]

i didnt have those issues with mine, mine like bogs down or goes to really high gears at low speeds, so im vr30 trans swapping it

[@markzinchuk]

Hey, yeah I’ve heard of other people having the same issue. I only had the not shifting past 3rd gear issue but it did always display the gear up in the cluster. Unfortunately I’m not sure what that issue would be so I can’t really help w that but after putting in a used valve body in it fixed my issue with no problems!

[@incrediblehak2833]

I'm not getting any codes for a tcm problem but i really think that's my problem. After driving some time my car's traction light comes on and the gears on my car start going haywire. It starts jolting and jerking really hard and sometimes gets stuck in certain gears . But i turn my car off a few seconds and the traction control light goes away and car is back to normal until i get back in the highway or drive for a long time. Any thoughts?

[@markzinchuk]

Thats pretty weird! I’d look on forums and see someone might have the same problem but that seems like something faulty obviously if it’s bad then works randomly yk. Sorry I couldn’t really help with that, I’m not too sure.

[@AlejandroTorres-bl2kb]

If i buy a new valve body 2015 q50 3.7 from the infiniti dealership do I need to reprogram it? Or its plug and play.

[@markzinchuk]

Hey, honestly, I’m not exactly sure with the new ones if you would need programming. Pretty sure you don’t but I’m not 100% sure on that. I actually ended up getting a used one from a junkyard for way cheaper and put it in and it worked perfectly without any programming or anything. That would save a lot of money as well.

[@onieshianapoleon2547]

​@@markzinchuk so what did this part cost $ ?

[@markzinchuk]

@@onieshianapoleon2547 the remanufactured part I believe was around $300. I ended up returning it though and bought a used one for $100

[@jessearellano5664]

@markzinchuk where can I get a used one for a 2015 3.7 q50

[@markzinchuk]

@@jessearellano5664 I bought mine off of a friend who had a parts G37 but if you don’t know anyone that has one I would say look if someone is doing a part out or if any junkyards have them. I think that would be the best bet for the price.

[@israelchavez1815]

What year was the car you got the valve body from I have a 15 q50 wondering if a 2013 g37 valve body would work

[@markzinchuk]

It was off of a 2010 g37 7 speed auto

[@joeduran7697]

this has helped a lot; I'm about to do my wife's QX70. Were the bolts different size, I have my diagram printed out but figured I'd ask

[@markzinchuk]

I’m glad to hear that it has helped you! Yeah, doing the job yourself can be a pain, but can save you some good money in the end! I’m honestly not sure about that, sorry.

[@joeduran7697]

@markzinchuk I'll post a follow and hopefully that will help folks as well.

[@markzinchuk]

Sounds good!

[@corymontano2661]

Did you torque down the valve body bolts or just screw them down tight

[@markzinchuk]

I just screwed them down, pretty snug. I know there’s a certain torque to them, but I just snugged them down pretty tight, making sure to not do too much.

[@wesdriver]

Everything is 70 INCH LBS including the pan bolts. About 6 FT LBS

[@howelldesierto4225]

just screw it tight

[@jamaicajamaica5292]

Hey I got the same problem here question..should I buy the valve body with the tcm or without?

[@markzinchuk]

I bought a used one with a tcm on it and it worked! I’m not sure if you do without it though I haven’t looked into that

[@mayuriwalker1512]

Any relearn or calibration type process necessary after the job?

[@markzinchuk]

With the remanufactured one you would need to get it reprogrammed because mine didn’t work after the video. I ended up buying a used one off of another g37 and didn’t need any calibration process or anything like that. So I ended up returning the manufactured one. In my opinion, I was strongly suggest just going with a used one.

[@andryabhd9030]

A question, if my Q60/G37 is AWD, do I have to look for a valve body that comes from a G37 AWD?

[@markzinchuk]

@@andryabhd9030 I’m not exactly sure. Id look it up if they’re the same transmissions!

[@steelheartg]

Thank you for this video

[@markzinchuk]

@@steelheartg No problem! Just here to help!

[@1of1.92]

the transmission dipstick is actually behind the engine you can fill it up through there .

[@markzinchuk]

Yes, on the 2008 and 2009 I believe, but once they put in the 7 speed it doesn’t have a dipstick.

[@brettgooseauto4390]

was there a seal kit between the valve body and the transmission?

[@vursce]

No, there is also no seal/gasket for the trans pan.

[@markzinchuk]

No, there isn’t any gasket or seal there, just make sure to evenly tighten down so it doesn’t leak

[@lorenzolockett6065]

Does the black female plug pull out aswell or do you just pull out the green plug and leave the black one alone?

[@markzinchuk]

I just unplugged the green male plug and left the black female part in there. That’s what I can recall and from what I did in the video. It’s been about a year since the job so sorry if I don’t remember everything exactly 😂

[@MertYildiz-u6k]

hey so i got a 2015 q60 with a p0720 and p0500 codes, i believe this might fix it. where should i scrap the part from another 7 speed coupe? its awd

[@markzinchuk]

Since the remanufactured one did not work, I ended up buying a used one off of my brother that had a parts G 37. I’m not 100% sure where else to find them but maybe call around some junkyards and see if they have it. Good luck!

[@JuanSanchez-he4cr]

Hey I added a new valve body and new fluid it only starts in neutral do I have to disconnect the battery

[@markzinchuk]

@@JuanSanchez-he4cr I would try that yes, to reset the ECU since that is a pretty quick way of trying something. I’m not exactly sure why it’s doing that since I had mine in park and didn’t have to mess with that, but one thing I have seen is the gear selector that comes from tranny and has a slot on the valve body could be off, which could cause the car to not recognize or not start.

[@JuanSanchez-he4cr]

@ it eventually works but the reason I change my valve body is because when it transitions from gear 3 to 4 it revs up high and it kinda jerks once

[@markzinchuk]

@ that’s good! Yeah I’ve seen that. Mine wouldn’t shift past 3rd gear lol

[@JaredAlston-on7lo]

I know if I get a new one I have to reprogram but what if I get a refurbished one

[@markzinchuk]

Yes, you are correct. If you get a refurbished one you would also have to get that programmed. I did the same with mine, and put a remanufactured one in there and it didn’t fix my issue and I had to program but I didn’t know that at the time. But, I ended up putting a used one in there from another g37 with my same transmission and put it in there and fixed my problem without any reprogramming necessary. It’s way cheaper and worked!

[@JaredAlston-on7lo]

@@markzinchuk how do you reprogram them? Do I have to take it to dealer and If so typically how much to reprogram

[@markzinchuk]

@JaredAlston-on7lo I honestly do not know the answer to that one. At least for me, I called around and there are certain shops and places that do reprogramming, but I didn’t end up going with it so I’m not sure how much they charge.

[@shsk8880]

⁠yo bro how much was the new valve body from the junk yard ?? Im having the same issue with q50

[@markzinchuk]

@@shsk8880 I bought the used valve body off of someone I know for $100. I’m not honestly sure how much junk yards charge.

[@vciq]

Man so you replaced the whole thing ? How much did that cost ? I’m in the same situation at 75k miles …

[@markzinchuk]

Hey, sorry to hear that. But yeah, I replaced the entire thing but then I ended up shipping it back because I didn’t know that that speed sensor on the valve body needs to be re-coded. Because when I changed the valve did not fix it but then I called mechanics and they told me that I have to re-record it so now I’m kind of back to square one.

[@vciq]

@@markzinchuk that’s absolutely crazy I’m at a huge lose with part plus labor and don’t know what to do this sucks this should be a recall so many people go through this problem … thanks for the video

[@markzinchuk]

@@vciq yeah man, I’m only at 40 K miles with this issue. Glad I could help with showing how to take it out and replace the other! The valve body itself brand new on eBay costed me around $300. And yeah! That’s what I’ve been saying this whole time, I feel like it should be a recall or something. Infiniti really messed up on this part lol

[@vciq]

@@markzinchuk valve body is different than the entire module ? For $300 ? Idk what I have been looking at for $1500 mine won’t go out of 2nd gear and check engine went on

[@markzinchuk]

Yeah, that’s like the same issue with mine. Mine won’t go out of third gear. Yeah, gave to you if you go somewhere and they quote it for you it’s gonna be around that much that’s how much they even quoted me around that price. But since I went by myself to do it, it was a lot cheaper. Definitely some labor involved, but if that’s the issue and it will fix it I will definitely say for the price it’s worth it.

[@vqjerome]

Does it have to be the same year? Or does it need to be a 7at valve body 09 and up

[@markzinchuk]

It doesn’t have to be be same year, just same transmission like you said it has to be the 7AT. Mine came off of a 2010 g37 and I have a 2014 and it worked! It

[@vqjerome]

@@markzinchuk thank you I also have a 2014 q60

[@markzinchuk]

Yeah no problem! Glad I could help!

[@phigo4kins]

Hi, So you dont have/need to Program The Transmission After the VB Replacement?

[@markzinchuk]

Hey, in the video I put in the remanufactured one and that one would need a reprogram. What I ended up doing was putting in a used one from another g37 with the same transmission, I have I swapped it in and fix the issue perfectly without any reprogramming

[@funky3683]

@@markzinchuk did you get one from the same year model and trim

[@markzinchuk]

@funky3683 I actually got one from an older g37 but it HAS to be the same transmission. It doesn’t have to be same trim just same transmission!

[@markzinchuk]

Like for example, some of the old G37 have the 5 speed auto, and that will not work. What you need to do is get one with the same exact transmission. Like I have the 7 speed auto and I took it off of an older 7 speed auto, G37

[@funky3683]

@@markzinchuk thanks I thought it would I just wanted to make sure the ds and manual mode will still work

[@vursce]

Did you end up figuring it out after the reman version you bought didnt work? I hear those are a hit or miss type of thing. And the dealer has it priced at $2.5k just for the part…. I know LEVEL 10 Transmission shop in NJ has one but its $1k from them and I called them they said they dont do them anymore.

[@markzinchuk]

Hey! Unfortunately it didn’t fix the issue for me. After putting it in and stuff I called some tranny shops bc it didn’t work and they said that I need to get it coded to my car. I ended up taking it back out and putting the old one in.Basically back to square one, but trying to figure it out to see if I need to buy a new one again or get something recoded or programmed.

[@07wrxtr1]

@@markzinchukI would just get rid of that transmission and take it to the company in Ft Worth Tx - they'll upgrade you to the 7AT from the redsport. The larger TQ converter will allow for more heat dissipation - So if you're eyeing the supercharger from z1 - plan on ditching the stock 7AT first!!.

[@markzinchuk]

@@07wrxtr1 hey man, yeah I ended up just putting in a used valve body from another g37 and it fixed the issue with no problems! I definitely see what your saying but I’m going to be getting rid of the car soon and now being fixed I’m going to leave it lol.

[@levilee6488]

​@07wrxtr1 how much they want for that?

[@markzinchuk]

I paid around $100 for the used valve body off of a friend

[@djandfam4868]

Hey, i replaced my valve body from another Infiniti both q70L and now it want come out of park. What does that mean?

[@markzinchuk]

Hey, if I 100% honest I’m not really sure. I would love to help but when I did mine, it was in park as well and came out of park as it normally would. I’ve seen other people have this issue, so maybe you can find forums or something that has the same thing. Sorry that I couldn’t help with this one.

[@markzinchuk]

Best of luck to you!

[@djandfam4868]

The people you kno who had the same issue, still have the same problem now?

[@djandfam4868]

Or they jus said forget it and sold it because I’m thinking it’s side I did not put the gear selector in the right place ima try that when I get bck to my car but I will surely let you kno because I learned off of your video.👍🏾👍🏾👍🏾 big ups to you

[@markzinchuk]

@@djandfam4868 Yeah, the people that had the same issue. I’m honestly not sure what happened with their situation because some of them did not get back to me. But what you just said is well I’ve seen before as well aware, maybe the gear selector was not put in the right spot or something. I’m glad I can help you with the video , thank you!!

[@daveanator21]

I bought a refurbished one off of ebay. After installing in my 2015 q50 it gave me a "key system error" and the car wouldnt even try to start

[@markzinchuk]

Hello, I see you commented on my video a couple days ago and as shown in the video, I swapped in a remanufactured valve body and that did not end up working. So, this past week, I found a parts car, another G37 with around 100 K miles, and put that valve body into mine. No coding a reprogramming needed to be done, and it fixed the issue! Shift smoothly and goes through all of the gears now! So basically just find a used one, and it will work,hope this helps!

[@AniyahTeShae]

I bought a used valve body for my 2015 Infiniti q50. Waiting for the part to be delivered today or tomorrow. Did you ever get yours fixed ?

[@l3gacy430]

​@AniyahTeShae whatever happened? Did you install it and did it work without any programming? Also, what year was the valve body from?

[@markzinchuk]

From my experience, I put in a used valve body from another G37 and put it in and then it worked perfectly without any programming or anything needed!

[@adirbibi2070]

Same exact thing happened to me with the key system error did you ever get it figured out?

[@edmonmayfield2446]

So ur saying to buy one from a junkyard that’s programmed, the ones that are rebuilt on eBay have to be programmed??

[@markzinchuk]

Yes, from my experience, the rein Irbid ones on eBay needs to be programmed. I bought mine already used off of another random G37 at a junkyard with the same transmission as mine. And after that it worked for me without any programming!

[@edmonmayfield2446]

@@markzinchuk thanks for the info , my car is a q70 can’t find them in junkyard I wonder what other ones will work it’s a 7 speed transmission

[@markzinchuk]

@@edmonmayfield2446 Yeah gotcha, basically any of your same model with same transmission!

[@shsk8880]

@@markzinchukyo bro how much was the new valve body from the junk yard ?? Im having the same issue with q50

[@markzinchuk]

@shsk8880 I bought the used one from a friend of mines parts g37 for around $100. Not completely sure how much junkyards sell them for.

[@ryansteele5059]

Is this the same for the 2015 q50

[@markzinchuk]

@@ryansteele5059 not too sure but if it’s the same trans probably!

[@huzaifa1629]

What codes were u getting before fixing it ? Was it p0720?

[@markzinchuk]

Yes! It’s was PO720

[@crxzytv]

Did u have to programm

[@markzinchuk]

So with the remanufactured one that I had in the video didn’t work. I think they do have to be programmed though. But an even cheaper option that I did after the video was bought a used valve body off of another g37, put it in and it fixed the issue without any programming or anything!

[@mspjay1989]

Yu said g37 coupe has no dip stick wher do yu get your information

[@markzinchuk]

Hey, yeah they do not have a dipstick so there is kind of a process of seeing if you have enough fluid. Basically, there is a drain plug, and then a fill plug on the bottom of the pan. What do you want to do is make sure the car is level and then you put about 3 or so quarts in and then run the car and shift through the gears and make sure it’s warm and then fill up as needed. It should be around 4 or 5 quarts full (I’d look online). When the car is warm, open the fill plug, and if there is no drain and just tiny drops that you need to add more, and if there is a very solid drain, then you might have a little much. You kind of want to get into a middle ground, where there’s a decent flow And you might see some bubbles. There are KZbin videos on it if you want a better explanation. That’s what I did. Hope this helps!

[@mspjay1989]

@@markzinchuk dats a lie I have a 08 g37 coupe it has a dipstick

[@mspjay1989]

@@markzinchuk I have a 5 speed it has a dip stick same location as the g35 coupe

[@markzinchuk]

@@mspjay1989 sorry yes, the 08-9 has the dipstick. 2010 and up do not. Mines a 2014 q60 (renamed g37 coupe) so I don’t have one.

[@markzinchuk]

@@mspjay1989 yeah the 7 speeds such as mine doesn’t have one unfortunately, I wish I did 😂

[@andyhamilton8940]

Large pieces of cardboard for these jobs. Soaks up drips, provides cushioning, allows for easy sliding around.

[@ferny1479]

Does mileage matter when getting a used one?

[@markzinchuk]

@@ferny1479 I would probably advise not getting higher milage but I don’t think it really matters. My car had 44k miles and the used valve body I put in had around 100k and it’s been around a year since I did it and still no issues with the new owner!

[@ferny1479]

did you swap the original TCM onto the used valvebody?

[@markzinchuk]

@@ferny1479 I just put the used valve body in with whatever tcm was on it already.

[@ferny1479]

@@markzinchukok thanks

[@markzinchuk]

@@ferny1479 no problem!

[@ryansteele5059]

Does it have to be programmed

[@markzinchuk]

@@ryansteele5059 the remanufactured one yea, but the used one I ended up putting in didn’t need any programming or anything!

[@ryansteele5059]

@@markzinchuk Alr just bought a used one too wish me luck

[@ryansteele5059]

@@markzinchuk where did you buy yours

[@markzinchuk]

@@ryansteele5059 my buddy had a g37 parts car and I bought it off him

[@markzinchuk]

@@ryansteele5059 yessir good luck bro 🤞🏼

[@1weakv35]

I’m changing the whole trans

[@markzinchuk]

You could but if you have the same issue and want to save some money, I would definitely recommend changing out the valve for a used one, because I ended up doing that, and it worked perfectly!

[@BrokeBoiiSuave]

@@markzinchuk hey did you get the valve body from any year G37 sedan or coupe ?

[@markzinchuk]

@BrokeBoiiSuave Yes, my car is a 2014 Q60, which is the same as the G37 coupe, and I got the valve body off of a 2010 G37 sedan. The big thing you have to look out for to make sure it is the same transmission as yours. For example, they made the G37 with a five speed in the older years, and then a seven speed a little bit later on. So if you find one with the same transmission as yours, it should definitely work!

[@BrokeBoiiSuave]

@@markzinchukthank you for the information ❤🔥👍🏽!!!!

[@markzinchuk]

@@BrokeBoiiSuave yeah man of course, glad I could help! 💯

[@alainmedina8441]

How much fluid im I supposed to put

[@markzinchuk]

I looked on the Internet and found how much I was supposed to put in. The trick I learned which in the video I said, I didn’t understand, is that the car has to be level and you have to pump it with fluid and then run it to warm shifts to the gears, and then pump it more until once you take the pump out you’ll see the slight stream. If it’s flowing out a lot , then it might be too much, and if a bunch of bubbles, it might not be enough. A small stream should be enough, but I would look online and there are some great KZbin videos on how to do exactly.

[@jozefgabor5867]

How many l transmission fluid please? I have infiniti fx35 2009 with code P0729 anybody tried clean value body?

[@markzinchuk]

@@jozefgabor5867 for your exact model there should be something online for it. But for mine basically I know when it’s enough when there is a very small stream that flows out when the car is warmed up and leveled.

[@tru_qs]

Mine wont come out of park even after checking everything

[@markzinchuk]

@@tru_qs I’ve seen other people have the same thing. One thing could be the gear selector thing in the wrong position. Other wise I’m not completely sure but if you look on forums and I believe in these comments some people have the same issue!

[@tru_qs]

@@markzinchuk It probably is, but how do I make sure the gear selector is positioned right, my check engine light also went away.

[@markzinchuk]

So unfortunately to check is by opening it back up. When changing the valve body on the pass side of the car, there’s a grey thing that pulls out and in that should line up and go into a slot on the tranny. It’s kind of hard to explain lol

[@markzinchuk]

I didn’t have that happen to me so I don’t want to give you the wrong information, but, I know that is how the select thing works and has to be in the slot. I almost put mine together before double checking and the grey thing wasn’t in the slot so I had to get it in there

[@markzinchuk]

I’ve seen some people said to make sure it’s in neutral but I did mine in park and it worked perfectly