How To Change Power Steering Fluid -EricTheCarGuy

  Рет қаралды 1,351,775

EricTheCarGuy

EricTheCarGuy

Күн бұрын

Пікірлер: 713
@Haloruler64
@Haloruler64 10 жыл бұрын
I do this job a bit different. I hook up a line to a drain pain from the return line, just like this, but I use a clear line. Then I drain the reservoir, fill it with fresh fluid, and start turning the wheel lock to lock with the engine off and the front of the car off the ground. This will pump fluid through the system (pump, rack, and all back to the return line) and you'll see when the fluid is fully flushed. Dirty fluid will come out through the clear line, and when it turns clear and new, it's flushed. Reconnect the return line, then bleed the system by turning the wheel lock to lock with the cap off. This way, you don't ever run the pump dry.
@turborunner
@turborunner 10 жыл бұрын
yep that's how I do it as well, it's probably the best way since there is no chance of running dry
@IntradeMotors
@IntradeMotors 10 жыл бұрын
YES this is how its done correctly! Not letting friggen air in to the system Made me grind my teeth..............
@bevsucceeds
@bevsucceeds 7 жыл бұрын
This sounds more logical to me. Also several other videos say not to allow the pump to run without fluid.
@HPX584
@HPX584 5 жыл бұрын
Hey man doesn’t the car lock the steering wheel when the car is off. How do u turn it lock to lock with the car off??
@crossfirecat3594
@crossfirecat3594 5 жыл бұрын
HD You turn the key to the run position only. You don’t crank it over or start it.
@infernolt7622
@infernolt7622 7 жыл бұрын
At first, I questioned allowing the pump to run dry. Two things changed my mind, however. 1. That's how the dealerships do it. And 2. It's a vein type pump (very durable) and the internal parts still have a small amount of lube on them. Once all the fluid is out, you shut it off. It's not like you're driving to the store with a dry pump. It's no different than starting up your engine after it's been sitting for a week and all the oil has completely drained down to the pan.
@jorgegveram1
@jorgegveram1 8 жыл бұрын
Thank Erick!!! i made the change of the power stering fluid on my honda Civic and was perfect!!! simple stuff for all non-profesional mechanics!!! You made IT simple!!! Thank again!! From Venezuela!!!
@mjremy2605
@mjremy2605 Жыл бұрын
Good to know you don't have to jack up the car as I don't have a sturdy jack! Also great to see what can go wrong like the clamp breaking off. If I don't have that spare part with me, I cannot drive to the store to get it, oh no! The hose clamp is so easy to put on and take off. I am not sure of all the tubing involved but it looks simple enough to try. These videos are so useful for car maintenance, very grateful to have this. Thank you! On a Toyota, power steering fluid should be changed every 2 yrs or 50,000 miles.
@suneilkumar
@suneilkumar 7 жыл бұрын
I love how Eric is a Honda guy. I look nowhere else for my auto needs.
@fabionmitchell9733
@fabionmitchell9733 4 жыл бұрын
Same here
@aventurajohn1988
@aventurajohn1988 3 жыл бұрын
How many bottles did he used ?
@FamousByFamily
@FamousByFamily 10 жыл бұрын
at the dealership that i work at we do these flushes all the time. usually we sell it up to customers with a fair amount of kms and now p/s fluid change or when they complain or power steering noise. we use this wynns power steering flush machine, which basically sucks out all the fluid from the reservoir then you add this wynns flush with DEXRON 6 fluid to top up the reservoir , then you turn the steering wheel a bunch of times to make sure the fluid gets circulated through the system, and finally you suck it back out again and repeat till you have used all the flush fluid. after we add this power steering treatment fluid and it definitely does a good job. I've heard of this process completely repairing old racks and pumps to virtually new condition. it's amazing what a bit of fluid will do.
@danielmontana1458
@danielmontana1458 8 жыл бұрын
There's an easier way. Just disconnect the hose from the reservoir at the pump, and let it drain into a bucket. Attach another piece of hose to the pump. Fill this hose with fresh fluid and put the end into a gallon jug of fresh fluid. Start the car and quickly (like 5 seconds or less) turn the wheel all the way back and forth, and shut it off. The pump will have sucked about 2 quarts from the jug and you'll have about 2 quarts of dirty fluid in the bucket. Reconnect the original hose and top off the reservoir, and you're done.
@delete6534
@delete6534 8 жыл бұрын
I watched the video thinking ETCG would show me this method...except I didn't think of the syphon in the clean fluid trick, I was just going to pour it in as it drained. Now I can do it without having a second person turn tje wheel. Thanks! N64
@j.jamessr.1446
@j.jamessr.1446 7 жыл бұрын
What size should the other hose be?
@AngelMendoza-nq6rq
@AngelMendoza-nq6rq 6 жыл бұрын
Really
@HealthFitnessMartialArtsDEng
@HealthFitnessMartialArtsDEng 6 жыл бұрын
I like your method. Then the system is still full and no air enters the system. Notice at the end of the video how loud the power steering pump was. Turning it lock to lock may not purge the air. May have to vacuum out the air. It would have been good to make sure the end of this video showed how the air was purged from the pump and listen to it quiet down.
@allent1034
@allent1034 5 жыл бұрын
A gallon of Power Steering fluid? With expensive car specific (honda) fluid that would be about $50. I think I will just have someone pouring fluid into the reservoir if it gets too low.
@crtmojo2705
@crtmojo2705 9 жыл бұрын
Thanks for the vids. My local shop wanted $100 per system plus fluids. This was for power steering, brakes, and clutch. You just saved me a fortune and I'm a little closer to getting those coilovers I wanted. Thanks again!!
@josephshultz6726
@josephshultz6726 Жыл бұрын
Let me know where that shop is (kidding), I'd pay $100 for those three fluid changes nowadays :)
@joejones9944
@joejones9944 Жыл бұрын
@@josephshultz6726 Exactly! Lol
@ericthecarguy
@ericthecarguy 10 жыл бұрын
I've been asked about making this video for a while. It's an often overlooked maintenance item. How To Change Power Steering Fluid -EricTheCarGuy
@Youngsoldier93
@Youngsoldier93 10 жыл бұрын
But how do you change blinker fluid? :)
@JohnSebeny
@JohnSebeny 10 жыл бұрын
Odd... He's not wearing his trademark white gloves!
@TomekBlacksMyth
@TomekBlacksMyth 10 жыл бұрын
Drain from the return line, turn on engine and turn tyres full left and full right, turn off engine. Reconnect return pipe, fill up, turn on engine, spin tyres as before, fill up to level. Let bubble. Am I getting this right?
@RealCadde
@RealCadde 10 жыл бұрын
Tomek Hermsgavordenbroker Check level after complete. Recheck level after a drive.
@christophermcgill39
@christophermcgill39 10 жыл бұрын
Thanks bro
@DillonTurner395
@DillonTurner395 9 жыл бұрын
Did this before watching this video, actually ended up doing it this way too lol issue I had is afterwards had issues with air in the system. Let it sit, fought it come kept going lock to lock to try to get the air out, seemed like almost nothing was working. Then decided wth ill take it for a stroll down the road and see what happens, my truck is an 04 f150 crew cab and without power steering its a bear to turn so I was hoping the end result wasnt going to be ending up in a ditch but sure enough after about 5-10 minutes of driving no more issues or whining! I was changing the fluid cause the valves in the rack were sticking causing random losses of power steering. Changing the fluid cleared it up and so far no more issues! So as a tip to anyone (maybe its a ford thing idk) having issues with air in the system afterwards take it up the road for a bit (try to keep it a straight road just incase) if it does well try a slightly curvy road and see if that clears it up, however im not responsible if you put your vehicle into a ditch!
@tablloyd5
@tablloyd5 7 жыл бұрын
I used a jack getting the front wheels off the ground. blocking the rear wheels. It turned much easier, and not as much wear on tires, garage floor, or driveway. Those who complain that doing this procedure will damage the pump because it is running "dry:" The pump doesn't run "dry" as we think of dry like causing friction. When we pour oil into the engine doing an oil change we say the bottle is empty, or dry. But notice in the empty bottle -- there is still some oil coating the inside plus in the bottom. It is not "dry" in that sense of the word, nor is it "empty" in that it still contains some, not much, but some oil. Same with the ps pump, it has been "emptied" but it not "dry" because there is always that coating of fluid inside the pump which will not be damaged because it is not run that long after the purge.
@redlense4
@redlense4 8 жыл бұрын
Eric, I just performed this procedure on my '08 Subaru Outback. It steers like a dream now. Thanks!
@charleskennedy23
@charleskennedy23 8 жыл бұрын
Great video eric! I just did this on my 2008 Odyssey. I pulled out 4-5 ounces through a turkey baster... I then unplugged the return line and routed it directly to an empty 20 oz soda bottle. Ran the engine for 30 seconds or so turning the wheel lock to lock to get the rest of the fluid... All total I pulled about 22 ounces out of the system... Refill procedure as follows: replaced with 12 ounces... ran engine to burp system... repeated three more times (4 oz / 4 oz / 2oz). Worked like a champ! Super easy maintenance item. Old fluid had 99,000 miles on it wand was really dirty! Since it is so easy, I'm going to try this again in 3-years. I'll report on what 3 year old fluid looks like at that time. Thanks for the vid! Definitely gave me the confidence to give this repair a shot!
@johnstack5008
@johnstack5008 8 жыл бұрын
+Charles Kennedy Did you unplug the return line at the reservoir or somewhere else?
@charleskennedy23
@charleskennedy23 8 жыл бұрын
+deep stick reservoir… ran the line directly into the soda bottle… Kind of a tight fit, but if you get a skinny bottle you can find the room. Make sure get as much as you can with the turkey baster first!
@b286guy
@b286guy 10 жыл бұрын
The way I did it recently was to add a plastic tube onto the end of the return line and put a plug in the outlet of the reservoir. Then I started the engine and continued to pour new fluid into the reservoir as the old fluid was pumped out into a container. When the fluid started looking clean, I stopped the draining process, bled out the air, and topped off the level in the reservoir.
@joealberta
@joealberta 7 жыл бұрын
Hi Eric, I used this method and it worked great. Performed it a couple of times and it cleaned the power steering system well. I have a Honda service manual and this is the method they use. Probably is the only way to get it all out with all the pipe and tube bends in the system. Thanks.
@chhathchhuong6281
@chhathchhuong6281 8 жыл бұрын
Thank you ERIC The car guy and thank you your video showing us about flushing fluid from Power steering procedure. Once thank again.God Blessed you.
@johnkaplanian
@johnkaplanian 10 жыл бұрын
Dear Eric, sometimes it would be a good idea to remove the reservoir and spray its interior with a brake cleaner from the opposite side of the fluid flow hole and dry it with compressed air and keep it under the sun for a while, because there is a mesh at the bottom of the reservoir where I have seen in other makes that it became clogged with debris , dirt and cause steering difficulties or pump noises. Just FYI
@2885jutt
@2885jutt 10 жыл бұрын
Very informative, Eric. Like you, I had little to know idea if power steering fluid was part of the maintenance process for vehicles. And I certainly can understand that all fluids get old and need attention when the time comes...Thanks again Eric!!
@mkIIIsupras
@mkIIIsupras 10 жыл бұрын
that whine it made is exactly why you don't ever run the reservoir or pump empty. you had the right idea when you said have a funnel on the return hose to the reservoir. just fill keep filling it with till clean fluid comes out. if you have to much in the reservoir at the end, siphon some out.
@ailll1
@ailll1 10 жыл бұрын
What I did on my tacoma was fill with new fluid as I was draining the old. I jacked the front so I could turn the wheel easier. Turned the wheel left to right, right to left. Added fluid and repeated this process until new fluid would come out. That way I didn't have to do any bleeding and no air bubbles in the system.
@robby844
@robby844 10 жыл бұрын
I usually suck out what I can then add more. Cycle it. Suck it out and repeat the process until the fluid in the system is clear. Takes about 15-20 minutes and you don't have to disconnect anything or run the chance of you getting air in the system.
@discerningmind
@discerningmind 7 жыл бұрын
I do it this way too, but instead of doing in one shot I do it when I arrive home each day until it's clean. This method also works well to change automatic transmission fluid if you're not changing the filter. If the trans has a drain plug it's easy, otherwise a manual pump extractor with a long hose. I've changed brake fluid this way too extracting what I can from the master cylinder reservoir and repeat when the brake fluid in the reservoir looks dirty again.
@herbwag6456
@herbwag6456 6 жыл бұрын
I do the same things as you guys do. Works good enough!
@AikidoTubeSock
@AikidoTubeSock 5 жыл бұрын
Jake: How did you determine the 4-5 quarts? If your capacity is 1.5 quarts it would take about 2 to do it yourself
@invain143
@invain143 5 жыл бұрын
How about not switching the engine on, just turn the wheel lock to lock.?
@adrianesquivel2946
@adrianesquivel2946 5 жыл бұрын
@@invain143 how would the fluid cycle through if the car isn't running and the p/s pump isn't running
@iamasmurf1122
@iamasmurf1122 6 жыл бұрын
I have been doing this trade as well for a long time here in Australia and I don't like those type of clamps either, instead of reaching into the bottom of the engine bay why did you just not take hose off resovoir then get a pipe joiner join another pipe to it run that into a bucket and just bung up the resovoir pipe hole with something it is how I did it and it is much easier than having to get your whole arm into the engine
@colliemutt5
@colliemutt5 6 жыл бұрын
I greatly appreciate you taking the time to post this video. I just finished changing out the PSF on my 2003 Tacoma with 108K and the process went smoothly. Thanks
@PMitchell106
@PMitchell106 8 жыл бұрын
For those doing this on rough concrete, consider putting a piece of cardboard under the tires, the sides of a cereal box will work well, it will put a lot less strain on the system when turning the wheels, and will avoid leaving tire marks on the concrete.
@huoffk8469
@huoffk8469 7 жыл бұрын
PMitchell106 good idea thank you
@discerningmind
@discerningmind 7 жыл бұрын
What a great idea!
@huoffk8469
@huoffk8469 7 жыл бұрын
PMitchell106 I suggest 2 pieces of cereal box or cardboard each wheel as when I tried this it was still pretty hard with one layer under each wheel
@Sirach985
@Sirach985 6 жыл бұрын
Ugh I’m screwed. I only by Malt-o-meal bag cereal.....
@TheLongLouis
@TheLongLouis 6 жыл бұрын
I wish I saw this earlier. I never had those problems as mentioned, but it would have been easier to put cardboard under the wheels. I only had a oil catch can under the car.
@Tom-il5xu
@Tom-il5xu 7 жыл бұрын
Thanks for the video on power steering pump fluid replacement . I just replaced my power steering radiator coil / fin Leaking do to corrosion on the return line 2003 avalanche 1500 . I just bought a vac kit MITMV 8500 series to use to complete my work Thanks again Brian, TS
@jerri0401
@jerri0401 10 жыл бұрын
Doesnt it hurt the power steering pump if it runs without fluid? just curious
@ratdude747
@ratdude747 10 жыл бұрын
If you keep driving it that way yes. But for the short period of time during this job, no.
@EddieTheGrouch
@EddieTheGrouch 10 жыл бұрын
It shouldn't for the short amount of time involved. However, I have ran across pumps that will whine long after the new fluid is in place. It seems once air gets in there it can take a long time to get it out or an old marginal pump may get worse. To play it safe I prefer to siphon out the old fluid from the tank and fill with new before starting the flush. Very little (if any) mixing will take place. Fill the tank to the top to lessen the chance of running it dry (just like you would with a master cylinder while bleeding brakes). Then top off the tank. You waste a little new fluid that way but it's worth it to me.
@Tmjpwns
@Tmjpwns 10 жыл бұрын
Cavitation is a pump killer, but when it's just for changing fluids and/or first startup of a new pump it's fine as long as you get all the air out shortly after.
@freddyflintstoned913
@freddyflintstoned913 9 жыл бұрын
jerri0401 Yes.
@widtrak77
@widtrak77 6 жыл бұрын
Won't turning the wheels lock to lock with the engine OFF force the old fluid out as well?
@JeffHazardous
@JeffHazardous 10 жыл бұрын
Quick question. If someone were to do this, would it be beneficial to lift the front end up to turn the wheels lock to lock? maybe take a little stress off the system, especially if you bleed it almost dry like that.
@ericthecarguy
@ericthecarguy 10 жыл бұрын
Jeff Dooley I don't think so. As in this video the fluid ran out pretty quick. I never got the opportunity to turn the wheels and the system was empty.
@EddieTheGrouch
@EddieTheGrouch 10 жыл бұрын
It wouldn't hurt. For example, I have a 02' Chevy Tahoe. Owners are discouraged from making dry turns (wheels not rolling) as it stresses the poorly designed steering parts (idler, Pitman, etc) on a heavy vehicle. Also, the wider the tire the more stress. At the least, I like to have the wheels parked on corrugated cardboard. The cardboard layers will shear when the wheels are turned lessening the stress and making the steering easier to turn as the power assist fades.
@PawelTylinski
@PawelTylinski 10 жыл бұрын
Eddie the Grouch It is good to lift car a little, but if you are lazy there is a trick: you can use small amount of sand under each tire.
@JeffHazardous
@JeffHazardous 10 жыл бұрын
Thank you everyone, Going to be replacing a low pressure line on a 04 Montana and figured I am going to bleed the system during the removal, so may as well know all this :)
@dnlmachine4287
@dnlmachine4287 10 жыл бұрын
Move to Canada, do the procedure outside in winter et viola!! free ice lubrication!
@everythingphil9376
@everythingphil9376 7 жыл бұрын
When I did mine, I was hesitant to run it dry. My method was to keep pouring new fluid while someone turned the wheel lock to lock (with the front tires raised). Seem to work fine. Timing is everything though. The fluid gets sucked up FAST.
@aredesuyo
@aredesuyo 6 жыл бұрын
At 6:44 the fluid looks foamy. I had that problem (signaled by a loud whining noise at the power steering pump) in my 08 Odyssey until I replaced a little O-ring at the entrance to the power steering pump. When that O-ring goes bad, air gets sucked into the system, as evidenced by the foamy fluid in the reservoir.
@markwoten6679
@markwoten6679 3 жыл бұрын
I used a plastic bag around (below) any fitting that I’m going to disconnect. No worry about getting fluid on the ground or on any surface in the engine area. Limits any unneeded cleanup. Furthermore, I would never introduce air into a steering system. The MANUAL way.... Remove pump return line off the power steering reservoir. Next block off the return port on the reservoir. This allows you to use the reservoir to supply clean fluid to the pump. I used a short piece of clear plastic hose with one end bent back with a clamp. You can also install a bolt into that hose end. This hose will be installed on the reservoir return connection. The pump return hose is connected via a barb connection to another hose leading into a waste container. It can be done without starting the vehicle. Fill reservoir and turn steering wheel all the way one direction and back the full other way. The call the Block to Block. Do it a couple times. Fill reservoir again. Redo previous step of turning steering wheel full travel again. R to L L to R. You will notice clean fluid will start to push out the old fluid. It removed it all from the steering rack, pump and all system hoses. Keep doing this procedure of topping off of reservoir fluid and turning the steering wheel full travel. Once there is clean fluid noticeable going to waste container- STOP 🛑. Next reinstall the pump return hose to the fluid reservoir. Check fluid level. Start vehicle. Turn wheel block to block. Any air if any will be removed. Recheck reservoir and systems for any leaks. EASY JOB!!!
@-rudy-
@-rudy- 3 жыл бұрын
Eric's procedure is exactly how Honda's factory service manual recommends doing it.
@NHR450R
@NHR450R 10 жыл бұрын
I use a siphon pump to get all the fluid out of the reserve tank on my power steering pump and refill it with fresh Dexron III ATF. I do this about once a year just for peace of mind. With my truck (2008 Silverado 2500HD) the power steering pump also powers the brake booster instead of vacuum.
@rayplaag5665
@rayplaag5665 6 жыл бұрын
After watching this a while back ...Did it myself on our 05 trailblazer...The ole gal has a lot of miles on her never done before...worked great!! ...easy.!!...a little messy but that was my fault :) ..no harm to the pump at all...had a friend with me..another person does help...TNX..
@kimhowden1897
@kimhowden1897 7 жыл бұрын
Eric, your power steering fluid change video was great. You spoke clearly, precisely and presented a clear video. Very easy to follow and understand, regards Andrew
@SlickerThanYourAverage
@SlickerThanYourAverage 9 жыл бұрын
Good video. Eric a good add to this and other videos is that with stock hoses and clamps, the low pressure hose would be "clamped and the high pressure hose would be "crimped"
@kennethcawley6151
@kennethcawley6151 9 жыл бұрын
Hey Eric first of all i like all your videos i learned so much from them But now i have a problem with my truck its a 99 Ford Ranger 3.0 when I turn the steering wheel it has a bumping feeling to it and you See it in the front tire is that the power steering pump
@abandonedsc4261
@abandonedsc4261 9 жыл бұрын
It's nice when you have a few Acura and Honda products, to be able to see these maintenance and repair videos from someone who's been a Acura technician.
@zerofatzreturns
@zerofatzreturns 8 жыл бұрын
awesome video Eric! Big help man. I just had my wifes Santa Fe in the shop and they replaced the Steering Rack. But now for like 3 days I have had to keep adding power steering fluid. I have went through 2 bottles so far. Was checking this video for reference. To me after watching your video it seems like it should be about done going down in level. If it's not I think they might have messed something up and it's leaking somewhere. Either way man, appreciate all you do bro!
@BoomBoxBiZ
@BoomBoxBiZ 8 жыл бұрын
Definitely leaking
@attpureownpk
@attpureownpk 10 жыл бұрын
thanks for the video! i have a 06 Acura TSX and everyone of your videos helps me in furthering my knowledge of keeping my vehicle in tip top shape. i have a certain love for the simplicity and compactness of the Honda engineers designs.
@DJDevon3
@DJDevon3 10 жыл бұрын
Why does it look so brown and nasty in the reservoir? Wouldn't contaminants in there be a concern? On my car I go back and forth with the steering wheel for a couple of minutes until all the air is bled out. It's a real work out on the arms but if you keep working it you'll eventually get rid of the whine.
@February54
@February54 10 жыл бұрын
There is a strainer on the bottom of the reservoir. Honda says if it is reasonably clean then the whole system is ok. Now if the strainer has a lot of gunk, you should replace the reservoir.
@February54
@February54 10 жыл бұрын
***** Well, if you can get inside and clean the sludge that forms, go ahead. But sometimes the sludge can be near impossible to clean and remove from each hole in the screen. If you change P/S fluid regularly, the screen will never clog and everything should be fine.
@gweedomurray9923
@gweedomurray9923 10 жыл бұрын
I'm too lazy to do all that jiggering with the line. Once a year about May, I run a hose out of the rezza-vwhah of my '99 Tahoe and collect 12 to 15 ounces of "juice" into a gallon bottle, and refill the reservoir. Once a year every year keeps the fluid "young". I do a brake lines flush around that same time and after some arbitrary miles which includes a couple of long distance trips a year, I drain the 3 qts. that the transmission will give up and refill with new stuff. I bought this car at 74,000 miles and now have over 250,500 on it and still with the same master cylinder, brake cylinders and rotors, power steering pump and auto 4spd trans. The alternator has been replaced once and the water pump is still the same one that it came with. I now do the coolant flush every 2 yrs.
@stinkycheese804
@stinkycheese804 9 жыл бұрын
***** What is loose in the reservoir should (mostly) drain out with the fluid change. What remains is stuck on and may stay there forever and still you have to remember that it's coming from the hoses or rack seals so getting rid of it all doesn't change that the source producing it is still there. Certainly if you wish you, like if doing a rack change, you could take the reservoir off, INCLUDING off the pump mechanism, and plug the holes then fill it with a gentle abrasive and degreaser to clean the sludge out, but if it bothers you that much you could instead just get a new/clean reservoir.
@cameron20020
@cameron20020 10 жыл бұрын
Useful bit of info: As stated in the video, please use genuine honda power steering fluid. I can't stress that enough. Dextron 3 will ruin your pump, turn it into a noisy whining mess. (as it also ruins honda transmissions). Know from experience because it stuffed up the steering pump on my mums legend... and greatly shortened the transmissions life too. Another useful bit of info, you can use fork oil 15 instead of Honda fluid power steering fluid. This stuff works great, and I used it for several years and many thousands of Ks on my prelude. Much cheaper, and works PERFECT! As for the transmission fluid, nullon or penrite fully synthetic fluid seems to work a treat too.
@peter-dt6rh
@peter-dt6rh 2 жыл бұрын
Thanks🍭good job of telling the duration and volume of power steering fluid... Wondering about the o-ring replacement too.
@Justacogg
@Justacogg Жыл бұрын
Would it be beneficial to keep a flow of fresh fluid into the system while draining it? Letting it run dry, will that cause damage? Would it also make refilling and purging more time consuming?
@MrWoowootila
@MrWoowootila 10 жыл бұрын
Eric I think that is a great recommendation on fluid change. If the manufacturer says its a lifetime fluid or part a good Rule of Thumb 100,000 miles. Lifetime Coolant, Power Steering Fluid, Fuel Filters. Personally I change it way before just to extend the life of the system, but it has not been changed by 100k then change it.
@theroyalcrownedtiger2946
@theroyalcrownedtiger2946 3 жыл бұрын
Thank You, now I shall change the power steering fluid for my Chevy Venture minivan.
@ariesr4883
@ariesr4883 5 жыл бұрын
Great video! My friends RSX rack and pinion has been changed out but it’s using non Honda fluids. if we changed it out and flushed it with oem Honda fluid will the system be okay or is the system contaminated?
@scottfree2929
@scottfree2929 7 жыл бұрын
I used PEAK ps fluid and it looks like a 30w oil. Steering is acting sluggish and ps line leaking. I'm replacing the line tomorrow and plan to install a fuel line filter on return line. It will be on until we have another warm day or a month. Didn't feel draining the PS unit dry is the way to go. I have enough trouble with a contaminated system. But, good video as always. I noticed this is an old video. Do you use vacuum to get the air out of system or still old school?
@tonycj7860
@tonycj7860 10 жыл бұрын
Would it also be recommended to change the hoses hooked up to the power steering reservoir as a precautionary measure?
@All2Skitzd
@All2Skitzd 9 жыл бұрын
Almost ever manufacture now recommends vacuum bleeding to remove air from the system. Also some recommend against adding a filter on a system that was not designed for it. It's ok to put brake cleaner on rubber parts?
@davidcordon1600
@davidcordon1600 10 жыл бұрын
I just changed the PS fluid on my 2009 Buick Enclave. That hose was a bear to get at! They are notorious for having loud whining pumps, and a newer TSB calls for Dexron VI. Once I refilled, it was squeeling and vibrating like crazy when I turned the wheels. It took about an hour of wheel turning (first with engine off, then for short periods on) and adding fluid to get all the air out of the system. I had heard they were hard to get the air out of, but it seemed like a ridiculous amount of time.
@jared5220
@jared5220 10 жыл бұрын
When I change power steering pump fluid I've followed this same procedure Eric does with a pretty minor change. Instead of running the car I jack the front wheels off the ground and turn the steering rack lock to lock. I've noticed one direction will suck the fluid from the reservoir and turning it the other way will pump it out to the return line. I was always pretty worried I'd burn out the pump and this has allowed me to change all the fluid without running the pump and avoided possible dry running issues. Thoughts?
@sandrarichardson2713
@sandrarichardson2713 2 жыл бұрын
After viewing many videos and reading hundreds of comments....I believe your method is the best of many as it does not have the possibility of harming the starter and introduces the least amount of air into the system. Had to order the ATF as local stores did not have the brand I needed...but when it comes in I will be confident in using the method you use. Thanks and Jesus bless.
@vikingtu
@vikingtu 9 жыл бұрын
Is this OK for a 00 Town and Country? I have some whining when from the pump and the fluid has never been changed...148000 miles 3.80L. Great videos....very helpful.
@MattJonesYT
@MattJonesYT 3 жыл бұрын
This method runs the pump and rack dry and introduces air bubbles after refilling. Better is to not let the reservoir go empty but keep filling it as it is emptied. Pumping the fluid out just by turning the wheel but without turning the car on is the safest way to go.
@NGinuity
@NGinuity 10 жыл бұрын
Did this in my Mazda 3 this past weekend. The return line was a pain to get to, had to take off the fender well cover to get to it. I just covered up the belts on the engine with a small piece of cardboard and stuck an old turkey pan under the car. Already had the wheels off for brakes.
@albertocharris7649
@albertocharris7649 8 жыл бұрын
i think you can turn the wheels t lock to lock only if the wheels are suspended in the air so it will cause less stress to your hidraulic system
@infernolt7622
@infernolt7622 4 жыл бұрын
Do you have to run the engine to drain the system? I saw a video where the guy turned the wheel stop to stop, engine off, with the wheels off the ground and drained it through the return line as you did.
@LivingInSantaClarita
@LivingInSantaClarita 4 жыл бұрын
Thank you for showing me how to do that. I have a 06 E and have a power steering leak. I was going to start replacing O rings one by one to see if that will stop the leak. Any suggestions on that?
@charlesmalone1303
@charlesmalone1303 Жыл бұрын
Hi Eric , That was very good information on how to change power steering fluid.
@rfmerrill
@rfmerrill 8 жыл бұрын
I'm an engineer. If I were designing a car I would for damn sure make certain that the power steering pump can run dry for quite a while without dying. If my bosses insist on shipping a car with a power steering pump that dies from 10 seconds of running dry, I would quit.
@johnathangrey3463
@johnathangrey3463 6 жыл бұрын
rfmerrill, do you know anything about ballistics engineering?
@348frank348
@348frank348 6 жыл бұрын
what kind of engineering?
@CarlosRodriguez-hb3vq
@CarlosRodriguez-hb3vq 6 жыл бұрын
From my experience with the same Honda power steering systems, if you run the pump dry, or even get a little air in the pump, it will screech terribly. That can’t be a good sound. Turning lock to lock helps clear out the air, but it takes my cars longer than 10 seconds to purge the air. A much easier method is to suck the reservoir out with a turkey baster and refill with fresh fluid every few oil changes. I know it doesn’t purge the system, but over time it has the same effect.
@kuromurasaki5273
@kuromurasaki5273 6 жыл бұрын
If you were a great engineer, you would develop a manual rack so you don't have the power system as a point of failure. People are stupid and they literally take almost zero effort as long as the tires are moving. I've removed the power steering from cars, so the ratio should've made it hell, but it didn't, unless the car was stationary, then you had to use some muscle. So, engineer a variable rate manual rack that switches ratio at 0-5 mph and you win.
@robmendoza6210
@robmendoza6210 6 жыл бұрын
@Jake McCoy is right but I am going to add this along with kuro,I have deemed Physically weak to that degree people should not drive. The sounds like a hazard to have on the road.What will they do when the power steering pump dies and they find themselves behind the wheel⛍☠
@Ottonic6
@Ottonic6 6 жыл бұрын
I myself would just unhook the return line and feed it into a bucket then have one person turning the wheel while the other slowly adds fresh fluid to the reservoir till I see clean new fluid coming out that way it never runs dry... Like Eric stated, it didn't take long for it to run out, so I wouldn't worry about wasting fluid to do it this way....
@Dub-ry4cs
@Dub-ry4cs 7 жыл бұрын
Did you hear the difference in the sound of the pump from the first time he ran the engine, when there was fluid in there, to the second time he ran the engine, after running the pump dry. It was incredibly loud the second time around. That sounds like damage to me. I'll stick to the no running the engine method.
@darktoadone5068
@darktoadone5068 4 жыл бұрын
I bought one of those extractors that are hand pumped, made it so much easier and no mess at all. I spent $45 for it.
@waynefoutz
@waynefoutz 10 жыл бұрын
My Dodge minivan's reservoir has a screen in it that was pretty plugged up, enough to make the pump growl and complain. Replacing that is a good idea too on a lot of cars. Mine was only $24, pump is happy and quiet now. To drain, I just stuck the return line into a gallon jug, fired up the engine and turned the wheel a couple times. It made a mess, but it wasn't too bad.
@dixoncider7256
@dixoncider7256 10 жыл бұрын
can you clean those with carb cleaner too?
@waynefoutz
@waynefoutz 10 жыл бұрын
Dixon Cider yeah, I have heard of people doing that. Mine was pretty filthy, so I just replaced it
@SeraphOfAsgard
@SeraphOfAsgard 9 жыл бұрын
What is a power steering fluid flush? Do you use some kind of detergent to clean the lines?
@leonava3314
@leonava3314 8 жыл бұрын
Hi erick, how did you blew off the air/bubbles? i thougt u will keep the your hose to bleed completly with using little amount of fluid.?
@jonasgrumby1093
@jonasgrumby1093 6 жыл бұрын
Next: how to change out the power steering pump.
@BWater-yq3jx
@BWater-yq3jx 3 жыл бұрын
Yes I was surprised he ran the engine. Better to turn it over without starting. And of course keep topping it up.
@A_guy840
@A_guy840 3 жыл бұрын
I was also surprised he ran the engine but was even more surprised to find that the service manual for the element agrees with Eric! :O
@BellyUpFishGarage
@BellyUpFishGarage 3 жыл бұрын
My service manual seems to agree with Eric as well....
@anisena16
@anisena16 3 жыл бұрын
Its not like he drove to mexico city with no power steering fluid. Running for 2 mins won’t hurt it.
@evanray8413
@evanray8413 2 жыл бұрын
I want to like this comment, but it has 69 already.
@yarpos
@yarpos 10 жыл бұрын
Just wondering about the clamp. A high pressure clamp comes off and a normal hose clamp goes on. Does it not matter in that area or am I just wrong and a clamp is clamp is a clamp?
@KillerJoeFIN
@KillerJoeFIN 8 жыл бұрын
I just changed power steering oil for -01 golf and -98 Passat. I made a adapter to connect vacuum oil extractor to return line and used that to get oil out and turning wheels without starting the engine. Much safer, with this method pump doesn't run dry. Passat has its filter at return line side in reservoir so I use hose to connect vacuum to return line connection and use just little bit fresh oil to clean filter before I remove extractor and fill system with oil.
@williamaduamanfoh7423
@williamaduamanfoh7423 7 жыл бұрын
Hi Eric, do you have a video of how to adjust the parking brake lever on 05 acura Tl auto trans? I think its easy but I don`t want to break any part doing it for the first time. Thanks Eric.
@dfields9511
@dfields9511 3 жыл бұрын
Gr8 vid, I did a 3x drain reservoir & fill procedure instead for a Nissan Maxima. However on that car. it uses ATF fluid (matic-D) instead of power steering fluid. This is great to know of another way to do this.
@michaelpaterson8086
@michaelpaterson8086 2 жыл бұрын
Hi Eric, great video, how many litres of power steering fluid would I need to do a complete flush and refill as you did but on a 2000 civic ej9/ ej6 ?
@fossilfish786
@fossilfish786 10 жыл бұрын
Great vid as usual, Thanks for this, lots of Honda forums confirm that for Honda's fluid is the one that is recommended and I ordered it and it solved issues that the car had running standard fluid even though it was change less than a year ago.
@rudysalas9138
@rudysalas9138 8 жыл бұрын
i personally use a turkey baster and pull out as much as i can from the reservoir and then top off with new ps fluid. after a couple hundred miles later, i repeat the process to get as much of the old fluid out. Never put just any ps fluid! put recommended for you car or else it would bubble in the system
@EulogizingSleep
@EulogizingSleep 3 жыл бұрын
yea this is the easiest way lol, it's a lot like how you change automatic transmission fluid in a Honda
@ez12beme1
@ez12beme1 9 жыл бұрын
I liked how you drained it, I question why not jack front tires off ground to remove the pressure on wheels? also question why you don't warn folks how easy it is to burn up the pump until the end when running without any fluid.
@shakengandulf
@shakengandulf 9 жыл бұрын
I'm thinking it would take a while for that to happen, if you're only going to be a minute at most, I can't see it being a problem at all. Apparently the manual for that car says to do it that way. "Read from another comment"
@rabidsminions2079
@rabidsminions2079 7 жыл бұрын
I use a large syringe to remove all the old power steering fluid from the reservior and fill it with new fluid. It takes a few times to clear the old fluid out with new fluid. easy diy.
@LoveClassicMusic0205
@LoveClassicMusic0205 7 жыл бұрын
I've done the same except I used a hand operated siphon. I did about 4 or 5 fluid changes, started the engine between changes while turning the steering wheel in both directions with the front wheels jacked up off the floor, and figure I got about 90+% of the old fluid out. Good enough.
@1marcelfilms
@1marcelfilms 3 ай бұрын
Its faster if you suck out the fluid and move the steering while from lock to lock with engine off and suck again. and repeat until no new fluid appears. then fill
@drez2857
@drez2857 9 жыл бұрын
Hi Eric I have done what was told but then I did not put a new power steering fluid in for about 2 weeks. A few days ago, I put the fluid it; now the steering wheel becomes very heavy and stiff. Do you have any suggestion what a problem would be? Thanks
@JonTheLostVirgin
@JonTheLostVirgin 9 жыл бұрын
I've always heard to lift the front wheels and go lock to lock with the engine off to bleed the system. Supposedly that prevents aeration. Does it really matter in the end?
@jimdavidson5208
@jimdavidson5208 8 жыл бұрын
What about draining the system, fill with diesel and drain then refill with the proper PS fluid? Turning lock to lock at all times to push all the fluid out?
@Legendnum23
@Legendnum23 7 жыл бұрын
I have a question what about Jeep mopar steering fluid? They don't make it anymore and I know not to put any different fluids out there what should I use? There's nothing in the Manuel saying using a different one or equivalent so which one should I get for a 99 Jeep Grand Cherokee limited?
@conscience-commenter
@conscience-commenter 3 жыл бұрын
To bleed any air from the system , remove reservoir cover put a screen with something to hold it on top, turn rack to rack until it stops spitting up and the system has been flushed of air. Just like an Italian grandmother uses a screen to contain a spitting red sauce for Sunday dinner .
@henry-lv8vk
@henry-lv8vk 7 жыл бұрын
if you don't want dirty fluid in a new steering gear box, would you drain the system first before making repairs? thank you
@pauloelze9937
@pauloelze9937 8 жыл бұрын
Eric, I have a 2005 Accord V6. The power steering is non-existent when the car is idling. I replaced the pump with an aftermarket MasterPro pump as well as replaced the fluid with Honda brand. I still have the same lack of power steering at idle. Any thoughts?
@oudude27
@oudude27 10 жыл бұрын
Eric, do you have a video on changing the slave cylinder for a clutch? The good old Integra
@FrenchValleyAirport
@FrenchValleyAirport 10 жыл бұрын
He already has a video for that on a civic. He did the master and slave.
@Vanuatoo
@Vanuatoo 10 жыл бұрын
Eric, is it OK to just take some amount from the reservoir with turkey booster and put the same (fresh) amount back? Of course it's not the complete change, but if I do it twice with some interval (let's say 1000 miles), will it be close to full change?
@DMAN22yeah
@DMAN22yeah 7 жыл бұрын
I plan on doing this in my 2006 accord as the fluid is brown, but can i suck out fluid from the reservoir, turn wheel and suck out more until no fluid comes out and the, fill back up? Im looking to do it the easy way. The only fluid i can get easily would be the prestone honda/acura fluid, would this be a good choice or should i source genuine honda fluid?
@s.a.clyde-mckay2602
@s.a.clyde-mckay2602 4 жыл бұрын
Eric do you have experience working on a Nissan I really hate them but my niece has one and I have some issues that need to be resolved ASAP on a 2013 Sentra (pure drive) transmission
@axelasdf
@axelasdf 10 жыл бұрын
What is brake cleaner, and where shouldn't I use it when cleaning repair jobs? Seems like a go-to.
@dnlmachine4287
@dnlmachine4287 10 жыл бұрын
Chlorine + Alcohol. Try to get non-chlorinated type. Its bad for anything thats not metal, but you can hit rubber and plastic as long as youre not jamming into the material. Keep it off your paint if possible. Any auto store or larger department store (WalMart etc) has it.
@dixoncider7256
@dixoncider7256 10 жыл бұрын
i use simple green or engine degreaser and hose down in the driveway after messy jobs like this.
@gui9442
@gui9442 10 жыл бұрын
Hey eric, im a big fan of your channel! I need some help, my 2004 PT cruiser is making some noises when you give it gas, my mechanic says its the fly wheel, it drives perfect, theres no power loss when driving.its a really loud nocking noise!
@gui9442
@gui9442 10 жыл бұрын
i have a video up on my channel showing the car and the noise
@epidemia2007
@epidemia2007 10 жыл бұрын
Good luck with the answer...cause he never does!!.lol
@gui9442
@gui9442 10 жыл бұрын
WOOW ! IT ACTUALLY WORKED. THANKS MAN
@jonmo2694
@jonmo2694 Жыл бұрын
100k is good, I did my grand prix 05 @130k and it was too dirty..Pump is good so far. I would say 75-100k but alot of manuals say 50k.You can check with a clean baster if it's dirty, easy check. Great video man, thank you for it.
@johnd4348
@johnd4348 3 жыл бұрын
how often to change. I suck out the reserviour every oil change (every 3000 miles) and fill with fresh fluid. In 2 to 4 oil changes its practaly new fluid.
@johnwrench4speed
@johnwrench4speed 10 жыл бұрын
As an alternative to starting and running the engine to drain the power steering fluid, I remove the fuel pump relay, so the engine won't start, and just crank over the engine to pump the power steering fluid through the system (particularly when installing a brand new power steering pump). This, I have found, also cuts down on aeration of the fluid.
@drivn4895
@drivn4895 7 жыл бұрын
Is there a point at which the return or feed hose can become to stiff, and harden to the point of not operating correctly? I was going to change my fluid out today but the hoses seem really hard. Thought buying new hoses before a fluid flush might be a good idea...
@themetalmike187
@themetalmike187 2 жыл бұрын
Excellent video yet again. Can this method be used to bleed trapped air bubbles in the system in lieu of a vacuum pump?
@rickii2010
@rickii2010 7 жыл бұрын
hey Eric I thought power steering pumps shouldn't run empty at no time or it damages the bearing in the pump?
@jamesconway5221
@jamesconway5221 2 жыл бұрын
Hi Eric, excellent video, Many thank for taking the time to make it.👍
@trd-kp6143
@trd-kp6143 9 жыл бұрын
I just changed my power steering pump on my 1990 toyota pickup do to it leaking but now i cant get it to bleed out the air, steering is really stiff. ive done this repair on it several years ago and didn't have a problem after. so i cleaned out my reservoir filter screen thinking it might be clogged but nothing. Could it be my old pressure line or return line sucking in air? steering is really stiff.
@Sp33dYg0m3z510
@Sp33dYg0m3z510 10 жыл бұрын
Hey Eric my car is getting an engine swap. The engine that is in it currently works but has a knocking noise should I keep that engine and learn on it or just let the mechanic deal with it to get rid of it?
@HUBBABUBBADOOPYDOOP
@HUBBABUBBADOOPYDOOP 10 жыл бұрын
Because of it's nature & properties- and because of the type of my cars' brake system (TEVES MK II)- I flush my brake fluid every 3 years. It makes a huge difference with hoses, ABS valve blocks, calipers, and reduces pedal fade from the hot fluid boiling the water in it.
@saginaw60
@saginaw60 9 жыл бұрын
When ya change fluids ona jalopy should be determined by working conditions. Very cold weather causes contraction of fluid every time the motor cools down, that draws in humidity & dirt to the reservoir.
@stinkycheese804
@stinkycheese804 9 жыл бұрын
filter taylor Actually that isn't really relevant. The fluid formulations are chosen so they aren't especially effected by temperature except a small viscosity change and they aren't hygroscopic like many brake fluids. Further, if your system is getting humidity and dirt into it every time the engine cools down then you are going to have it happen continually regardless of whether you're doing a fluid change or not so you'd need to fix the leaking parts and clean the dirt off until then.
@OldSchoolDisco_channel
@OldSchoolDisco_channel 3 жыл бұрын
why you did't disconnect the returning hose on the reservoir? what is the quanity needed of Honda Power Steering Fluid?
@abdouallahuniverse5689
@abdouallahuniverse5689 Жыл бұрын
I am using Honda fluid, but I have issue in the cold extreme cold below 30, I have to wait for the car to run 10 minutes before I can turn the wheels, i think I need to change the fluid after running some trans tune sea foam, and see if the problem solved.
Power Steering Fluid Change QUICK and EASY
7:59
ChrisFix
Рет қаралды 3,8 МЛН
Honda Power Steering Pump Rebuild 98-02 -EricTheCarGuy
42:21
EricTheCarGuy
Рет қаралды 643 М.
Things You Should Never Do In An Automatic Car (Big Mistake)
15:08
Car Care Clues
Рет қаралды 871 М.
Honda Power Steering Fluid Service/Change
8:19
Big Dog50001 Automotive
Рет қаралды 936 М.
How To Replace  Brake Fluid by Yourself - EricTheCarGuy
15:11
EricTheCarGuy
Рет қаралды 3,2 МЛН
Change Power Steering Fluid in 10 minutes and $10 | Honda Odyssey 2014
5:35
Abdul Rafay's Production
Рет қаралды 29 М.
How to Super Flush Your Power Steering System
10:57
FordTechMakuloco
Рет қаралды 627 М.
How to Quick Flush Your Cars Cooling System
6:50
ChrisFix
Рет қаралды 8 МЛН
Honda Element Power Steering Fluid Change/Flush
11:47
Bryce Carlson
Рет қаралды 40 М.