As an aspiring diy-er, this video slowly became pure comedy as I began realizing there's a zero percent chance at doing this successfully myself.
@LJsGarage Жыл бұрын
Haha I love the honesty it was a rough one 😅
@jorgepino3676 Жыл бұрын
I felt the same way until i decided to do it.. after not able to pull out thr air intake on Sunday.. i left it all taken apart until Thursday and i finally got it out. It takes lots and lots of pulling
@realityhurts8697 Жыл бұрын
You can do it, it's just alot of little details
@LootenantXan Жыл бұрын
I am 100% confident in my abilities, and I am already irritated realizing I have to pull the manifold to get the driver side plugs.
@weldingjunkie3 ай бұрын
It’s very simple you can do it.
@davebo1324mi Жыл бұрын
This seems overly complicated for replacing some damn spark plugs. Thanks jeep 😒 Nice video btw!
@LJsGarage Жыл бұрын
haha thanks and yeah wait till you see the O2 sensor...
@SSHitMan Жыл бұрын
@@LJsGarage I took one look at where the O2 sensors are and then took it straight to the dealer. 😳
@atarisbetter91997 ай бұрын
@@LJsGarage once you get the intake tube off why can't you just replace the plugs on that side? It looks all open?
@timwoods17716 ай бұрын
My thoughts too.
@Kiddro226 ай бұрын
Try Removing the starter on a NorthStar engine......Smh!
@matthewjswider Жыл бұрын
What this guy left out: The nuts under the intake plenum on the right side (driver) are 13 mil The rear nut has a bracket on it for the condenser lines. You’ll need a long handled 13 box wrench to get it loose, flipping it back and forth each time. The 8 mil screws (7) that come out of the top of the plenum need to be completely removed, especially the rear one. The last two hoses can be removed after the plenum is halfway out. If you loosen the brackets with the 13’s enough and slide the plenum to the right it will come out of the bracket behind the throttle body.
@LJsGarage Жыл бұрын
Appreciate you my friend!
@matthewjswider Жыл бұрын
@@LJsGarage no problemo man. It may be DIY but we are all in this together. Human kind. :)
@lanceprzybyla76625 ай бұрын
I'm doing this now...thank you 🎉
@joshua7680 Жыл бұрын
I recently had to do the oil cooler and filter housing. Used this video as refrence because I decided to do my plugs and coil packs while I had it open
@LJsGarage Жыл бұрын
Awesome, glad you made it through! Hopefully not too much blood and tears.
@katiepalfini2979 Жыл бұрын
Welp guess I'm not doing it myself. Good description though.
@LJsGarage Жыл бұрын
😂 not going to try and convince you... It was not fun
@TheVaka1Ай бұрын
My same thoughts 🤣🤣
@weldingjunkie3 ай бұрын
Good video, the back bracket is a 13 mm at the bottom.. we also forgot to tell them about the 210 mm on the right hand side where coil 6 is….the only thing you didn’t have to do was you could’ve left a throttlebody on the intake itself. That’s what I typically do. Service data calls for 1.7 to 2.0hrs but can be done in 1 obviously not filming of course lol that slows it way down.
@LJsGarage3 ай бұрын
Good tips man much appreciated!
@deannapushruk42123 ай бұрын
Seems soo dam easy but it's intimidating. The submitter is doing an awesome job but I have no confidence. Thanks Jeep!
@LJsGarage2 ай бұрын
You can do it! Thanks for the kudos 😀
@deannapushruk42122 ай бұрын
@LJsGarage the 3rd spark plug is in back & under. It's the one that quit. Soo I'll have to dish out $$800 for a shop. All good! If I was a mechanic, no problemo. Thanks for the encouragement tho!
@shantiza33 Жыл бұрын
Trying to DIY car stuff lately…even with your guidance my eyes popped out lol ima just fork up the $ and have the dealership handle this one
@LJsGarage Жыл бұрын
🤣 too funny. Trust me I was in a good situation with working from home, second car, and time. I just paid 500 for them to do my O2 sensor so I sucked it up 😤
@shantiza33 Жыл бұрын
@@LJsGarage I feel you bro! Sometimes it’s worth paying to save that time, effort and risk. Appreciate you!
@tonytigere5684Ай бұрын
@@LJsGarage $500 for a O2 sensor? Wow is that a the jeep dealer or independent shop? If it’s at a independent shop, that’ll mean they he dealer is like $800-$1000 or so, maybe. Im not looking forward for that repair.
@tonytigere5684Ай бұрын
@@LJsGarage also I’ve noticed from our 2015 jgc Laredo bought new that all repairs done have all been expensive. Around 8 so far. 187k miles . Basic vehicle with euro brand prices.
@kikerules2 ай бұрын
hello, kinda related , oil pressure sensor for that car , is it located inside the manifold ?
@LJsGarage2 ай бұрын
Right under it sadly
@ZenforyaАй бұрын
You miss the chance to show us how to get to the hard screw
@LJsGarageАй бұрын
It was tough to film sorry!
@JF32304 Жыл бұрын
I just called the shop to see how much this is and they quoted $650. I'm a big DIY and this is cake, think I'll order the plugs here real soon.
@LJsGarage Жыл бұрын
Yeah its manageable for sure! 650 isnt too bad thats right at my budget for DIY lol
@coreychillis9754 Жыл бұрын
Jiffy lube charged me $130 but from stories i don't trust them😢
@JF32304 Жыл бұрын
@@coreychillis9754 jiffy lube isn't touching my vehicle lol lol. Not going to have some young punk changing out my plugs.
@terpz4711 ай бұрын
@@JF32304I used to be the young punk changing them. Till I got fired from jiffy for stealing money from company. Shitty paying job but I did love what I did. Still work on cars as side job. I was assistant manager at 21. I'm 22.
@bobdimartino673810 ай бұрын
guarantee he only did the the three easy ones i bet the plugs on the drivers side are a different brand i just did my brothers it's easy but a pain in the ass if that makes any sense @@coreychillis9754
@moisesjasso72094 ай бұрын
What should a spark plug be gap to? I have a 2017 Jeep grand Cherokee Laredo 2 Wheel Dr. 3.6.
@LJsGarage4 ай бұрын
.043/.044 gap if I recall
@daveprostine10558 ай бұрын
what oil cooler housing did you go with? there is that aluminum one by dorman that I've heard good and bad. mine weeps oil only when it gets really cold so having the dealer do it along with the plugs and coil packs as I like the vehicle.
@LJsGarage8 ай бұрын
I used the same OEM one and it leaked again 😒
@klkchulo5657 Жыл бұрын
Well, im changing mines since my jeep vibrates when idle
@LJsGarage Жыл бұрын
Good before it vibrates itself to death lol
@jorgepino3676 Жыл бұрын
Does the air intake case needs to clean?? Also why is there so much gunk in it?
@LJsGarage Жыл бұрын
Not usually and probably because this one had a rough life
@justdagoatgaming8460 Жыл бұрын
Did you disconnect the negative part of the battery first?
@LJsGarage Жыл бұрын
I did not mention it in this video but it is recommended to do! I did this while doing my oil cooler housing so I was all over the place
@justdagoatgaming8460 Жыл бұрын
@@LJsGarage thanks
@emgangofficial56719 ай бұрын
Why you removed the throttle body ?
@LJsGarage9 ай бұрын
To make more room. it makes it easier to get to the last two plugs
@JoseHernandez-nf4ep Жыл бұрын
Have you done fuel injector replacement?
@LJsGarage Жыл бұрын
Luckily I have not 🙏🏿
@EmmanuelGuzman-n2nАй бұрын
Does anyone know the line/hose that broke at 2:24
@LJsGarageАй бұрын
Evap Purge hose I believe you are talking about
@UncRex7 ай бұрын
So ✍️ completely break down the engine ✍️ drop a 13 pound weight on it ✍️ and then have a seizure because you forgot how you tore it down. Got it! 😂
@LJsGarage7 ай бұрын
😂 it's a hot mess.
@BigHomie030 Жыл бұрын
What spark plug is in there originally
@LJsGarage Жыл бұрын
SP149125AE I believe is the part number for the Factory ones
@The000000007 Жыл бұрын
Champion Spark Plugs original Jeep
@kuvasz1014 ай бұрын
This post is not accurate. You do not need to loosen the lower bracket that attaches to the intake. This is an extra laborious unnecessary process.
@LJsGarage4 ай бұрын
Thanks noted for next go around
@jorges174410 ай бұрын
Do you have to replace the intake manifold gaskets when doing this?
@zacht67879 ай бұрын
No, unless you notice they're messed up - either seal isn't right anymore, it's cracked, or broken
@zacht67879 ай бұрын
If there's like 200k miles might as well replace it anyway since you'll be that far into it though
@LJsGarage9 ай бұрын
Depends on the mileage you're at might as well
@ogbean82 Жыл бұрын
Get it done now before it gets cold..
@LJsGarage Жыл бұрын
Absolutely!
@matthieuratrimoson3271 Жыл бұрын
An absolute nightmare of a job for me. After successfully getting the manifold off and installing the plugs, I have to remove it again to check if a connector is not on correctly. fml
@LJsGarage Жыл бұрын
Ohh no! That was my fear going into this, jeez. Treat yourself after this lol
@bobnunya76487 ай бұрын
You took way too much off to change plugs
@LJsGarage7 ай бұрын
I'm listening! Where can I cut time off
@weldingjunkie3 ай бұрын
No he didn’t lol the intake needs to come off my guy. Only the throttle body could of stayed
@sarahdemoss1469 Жыл бұрын
Good video. What did you do when the tube broke? What is that part called?
@LJsGarage Жыл бұрын
I taped it up for now lol it's the evap purge hose or purge valve. I'll replace it soon but it's like 50-75 for the whole thing 😒
@julianrodriguezvideo Жыл бұрын
The same thing happened to me and I glued it with tep and a waterproof liquid rubber spray. I don't know what it's called and what function it does,
@tonytigere5684Ай бұрын
What the !!! All that just to remove a spark plug
@LJsGarageАй бұрын
Yeah thats why they charge so much at the dealership
@boostboyracing8 ай бұрын
Yo this is crazy smh seriously
@LJsGarage8 ай бұрын
Yeah no joke 😞
@boostboyracing8 ай бұрын
Just got one 😂 smh
@PVPIDAV9 ай бұрын
🐱 🐱 🐱
@LJsGarage8 ай бұрын
lol
@mralapenosarespicy9 ай бұрын
I’m calling this project off
@LJsGarage9 ай бұрын
It's a hot mess lol
@philipcbarrera15376 ай бұрын
All these parts need to be taken off just to replace spark plugs…..Don’t buy a Jeep they look nice but not reliable in the long run. Buy Toyota or Honda . Most reliable on the road and east to replace plugs a 10 year old can do it😂😂😂
@LJsGarage6 ай бұрын
Hahah you're telling me
@benignobartolomebb5 ай бұрын
Ridiculous design
@realityhurts8697 Жыл бұрын
he over compicated this, unhook the coil connector pull up, remove only whats in the actual way... wow.
@LJsGarage Жыл бұрын
Maybe a bit but I make videos for a range of DIY skill levels. I can't only cater to people like you, but I appreciate the feedback
@realityhurts8697 Жыл бұрын
@@LJsGarage good point. I've been wrenching for 30 yrs alot have not.
@Dpshort111 ай бұрын
I agree. Seems like after the intake pipe is out you can see the coil packs clearly…
@hboozel5 ай бұрын
you called 3 different parts a "guy" within one minute. So that's all the farther I made it. I'm looking for a fellow mechanics advice not a youtuber.
@LJsGarage4 ай бұрын
Understandable
@murda65333 ай бұрын
I mean it’s not hard to see what he’s talking about, you shouldn’t be attempting this anyways if you don’t know the difference between a bolt and connector just cause he called it “guy” and now you’re confused
@kuvasz1014 ай бұрын
I just changed my plugs 2015 3.6 Grand Cherokee. I don't see the need to loosen the 2 lower bracket nuts on the driver's side. I removed the 2 nuts that attached to the 2 intake studs on the driver's side.
@LJsGarage4 ай бұрын
Yeah I realized that after for sure thank you!
@billwatcher9321 Жыл бұрын
Believe me, you do want to use a touch of anti-seize. Never trust "pre-coated". It's a really bad feeling in the pit of your stomach when the aluminum threads from the cylinder head come out with the plug !! Anti-sieze is very cheap insurance !
@LJsGarage Жыл бұрын
Understandable lol I have been alright so far, but I respect what you are saying
@MarkKeck Жыл бұрын
Just paid $ 427.00 at a dealer.
@LJsGarage Жыл бұрын
Honestly after doing it, if I didn't also have other work I needed to do I'd have just paid them. This sucks! Lol
@Kiddro224 ай бұрын
That’s not a bad price
@robertgelley64546 ай бұрын
excellent video! Straightforward and to the point without all the fluff. A+
@LJsGarage6 ай бұрын
Much appreciated! Hope it helped 🤞🏿
@michelecourtney4226 Жыл бұрын
How long did it take in real time to remove the cover etc. to get to plugs?
@LJsGarage Жыл бұрын
About 2 hrs actually not fun but doable
@ikc0000 Жыл бұрын
Wish you would’ve showed how to remove that dumb ass bolt near the firewall.
@LJsGarage Жыл бұрын
Yeah my B :/ that one stressed me out and I didn't even think to try and film it better
@jorgepino3676 Жыл бұрын
@LJs Garage could you described how you removed the 7th screw? I am stuck
@jorgepino3676 Жыл бұрын
What tool did you used?
@ThomasChapman6298Ай бұрын
The air suspension is one of the best features about the car imo I’ve been driving the 2014-2021 3.6’s two different ones a 2014 and now a 2015 for maybe 6 years now. But you can easily take on 8” it’s a great off road car great for mudding if you want to the only problem is you only have about 8”-1’ till you’re cutting it close to the bottom and a full skid isn’t standard so I would do any serious off roading like you’d do with a lifted wrangler where you’re driving over boulders and huge divots, but there’s still a lot of land you can run on.
@LJsGarageАй бұрын
Great point for sure can't argue!
@jordanbennett3814Ай бұрын
Just finished replacing the ignition coil and spark plug on cylinder 6. Not a fun job, but definitely beats taking it to a shop. Thanks for the tutorial!
@LJsGarageАй бұрын
Nice work! Glad it helped :D
@DaviSoares-th5bu3 ай бұрын
Thanks bro 🙏🏾👨🏽🔧 your video save me 2 hours
@LJsGarage3 ай бұрын
Glad I could help 👌🏿
@brentfodera3773 ай бұрын
Sure, it’s a fairly involved process, but in the end it’s just a sequence of bolts, screws, clamps and connectors. Nothing high tech. Just do it in order. Let’s say you normally earn 25 an hour, and you’d pay 600 for the job. Thats 24 hours, or 3 full days of work. It’s well worth it to do this yourself, and it’ll probably take no more than 5 hours for the least capable person.
@brentfodera3773 ай бұрын
And thanks for posting. It’s nice to have an idea about the scope of work before getting out there and figuring it out as you go.
@LJsGarage2 ай бұрын
You're very welcome my friend and absolutely true step by step and reverse!
@Mooseknuckle7132 ай бұрын
Facts
@CtCheech4880 Жыл бұрын
Yea, I have a feeling it will all go well until I have to put it back together
@LJsGarage Жыл бұрын
Haha it's a pain
@Runescapian19966 ай бұрын
What did you do about the tube you broke at 2:23 same thing happened to me