How To Change Transmission Fluid 02-07 Jeep Liberty

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@robertemmons2260]

I was looking for 2002 45RFE transmission slippage causes (loose bands, bad solenoids, bad fluid) when this video had popped up on my feed. This is a great instructional video for those who need to know how to change their transmission filter and fluid. But, I see one issue that was not mentioned, well maybe two. One; inspect the bottom of the pan for shiny flakes or chunks of metal. That is aluminum shavings which indicate that something is rubbing on the transmission body. Two; inspect the debris attached to the magnet BEFORE removing it to clean. Blackish fuzz is normal, shiny metal flakes indicate a possible issue of metal on metal grinding or shaving. I'd like to add that IF you use any type of RTV, DO NOT use too much! Excess squeezed to the inside of the pan lip can break loose and plug up ports, although the filter *should* prevent that from happening. Carry on.

[@Brian-vz7xe]

Rob are these Liberties outfitted with Aisin transmissions?

[@andreyloria2449]

Hi. It's a good guide, buy many Jeep Liberties does not have a deepstick. You should include that variation too.

[@ThisIsSolution]

I swapped my factory trans cover for an aftermarket unit with a drain bolt, now i can drain and fill sooo easy, easier than an oil change now!!

[@dylanpeel3081]

Still having good luck with this? Where did you buy it from?

[@ilzstdro6]

The ending of the vid where u check trans dip stick.. got my anxiety sky rocket with that rag.. hanging near the belts

[@1AAuto]

Thanks for checking us out. 1aauto.com +Dro Beats

[@joseph672]

How many quarts did you use to refill it?

[@killinallmusic6193]

Important question he didn’t answer smh because I just drained 8 quarts thinking it was gonna be four

[@7dire1]

Good Job Guys but i have question How much transmission fluid does it take ?

[@blackericdenice]

Why you did not use a pan gasket?

[@vickihawkes5329]

***** often does not seal well and leaks. and you can pump 2 quarts or more fluid out every oil change until you get to 14 quARTS and at least you know it's running fresh. Get a break pump or a genereal pump or fluid adder at the auto store or AMAZon for about $20-30$$$. easy way

[@blackericdenice]

+Vicki Hawkes I've drop many transmission pans and only use the gasket from the kit. I have a few videos showing this. Flushing is waste of time.

[@johnmcdonald8950]

blackericdenice

[@pjbachini]

G

[@quintenandjoannklonowski134]

I was wondering that too

[@kylewetzel4988]

Anyone else waiting for that ragged rag to get sucked into the motor?.....

[@quintenandjoannklonowski134]

yes lol

[@josephlachance8548]

If I did want to use a gasket, which one would be the correct one? There are too many choices out there. Thanks

[@davekana8388]

What brand RTV silicone did you use? Thanks

[@Graxster]

Gasket or not, you skipped one of the most important steps: Allow 24 hours for the RTV silicone to dry before adding transmission fluid.

[@Sbf347]

Graxster No need to wait that long

[@cal638]

@@Sbf347 i cud b wrong but when using rtv to form a gasket arent you suppose only tighten slightly so the seal forms then wait for it to cure( i would assume time varies depending on product) before tightening tighter or to torque specs

[@HARPO1ME]

What about the fluid in the torque converter?

[@rosspat11]

How much ATF fluid did you use to get it to the proper capacity?

[@MrSmith-jj9te]

One of those trans pan bolts, are marked and requires loctite to be used and installed back into the exact same hole that it came out of, according to Chrysler.

[@anguslean4058]

Driver’s side second one in - on the back side of the pan facing towards the rear wheels So Corner bolt is one - second one going towards the passenger side is the bolt you are talking about

[@anthonyhitchings1051]

You did not state the transmission type - was it the 42RLE?

[@thekinginyellow1744]

2007 doesn't have a dipstick. just a little cap that says "For dealer use only". plenty of threads about this issue on the internet. Automakers seem to hate people who work on their own cars.

[@anguslean4058]

On the 3.7 engine you can use the oil dip stick for checking the level Videos on KZbin

[@tufaraway]

What can I use to get trans fluid out of my wife's turkey pan?

[@e.v.g1451]

your credit card to buy her a new one

[@lopez12345ml]

Tehe lol

[@williampinson1125]

I'd like to see a video that includes evacuating the fluid in the torque converter and cooler for a full fluid change, along with the Quick Learn procedure with the scan tool or a DIY equivalent of that procedure.

[@1AAuto]

+William Pinson We're always cycling through common cars. We'll add this repair to our list! 1AAuto.com

[@drummerjstone]

Which models use the additional spin on filter? I got sold the kit with the spin on filter and it was like $50! If I don't need the spin on then I might be able to save money and buy a different kit

[@JoseCastillo-ll8mh]

i have a question one of the pipes in the left start to leak in my jeep is the same one as the one in the video. I live in Atlanta we went in a trip to South Carolina, everything was find when we got home i saw a lot of water coming from one of those pipes i want to know what it is?

[@quintenandjoannklonowski134]

AC water?

[@DeltaFoxtrotWhiskey3]

How much transmission fluid does it take?

[@sheltonsingletary2488]

I have a 2007 liberty sport. It does not have a dip stick How do I know how much fluid to put back in?

[@1AAuto]

+Shelton Singletary You should be able to find this information in your owner's manual. Thanks for watching!

[@anguslean4058]

Shelton you can use your oil dip stick Videos on KZbin

[@brwnjohnnysvage7251]

Can you do a speedometer sensor and the wiring

[@1AAuto]

+Rez Khan We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1aau.to/m/Shop-1AAuto-c

[@brwnjohnnysvage7251]

What are the torque specs for the case and the filter?

[@jerrysherer2534]

It takes 4 quarts of ATF plus 4 to do a service

[@modirimosiamiemang1700]

Hi What is the best transmission fluid for 2005 Jeep Cherokee 3.7L automatic petrol V6 ?

[@gobear6254]

Sorry so you can use gasket or RTV or gasket and RTV?

[@ryansoulik8743]

I have a jeep liberty 2003 with a manuel transmission. Is it the same process? It also doesn't have a dipstick.

[@gavinlorenz6837]

Hey Can someone help me? My jeep always stops trying to accelerate passdd 40 to 50 mph and I have to let off the gas and then press back down and it goes but I think it's the transmission slipping. I checked the fluid but I think it's fine but it might actually be too dark I'd have to check again.

[@felixaponte5685]

Need a new transmission.. Mines in the shop now 2500$

[@novemberecho71]

I have one concerne in the procedure Some people say a fluid change can « shock » the transmission I also have a bmw with a zf transmission and after fluid change i have to reset the adotative values. Of course its a higher end dsc tranmission... Is there some king of procedure or adptation of the transmission fo the 45rfe?... Thanks!

[@highplainsaccountability6482]

CarQuest Auto Parts said there's 2 filters, the 1 in the pan and the other is a spin on.

[@supermoistdeluxe]

possibly the same removal for a later model liberty?

[@dreamagery]

Yes. I agree. I recommend using the transmission gasket. They sell plenty of them. The paste is not secure enough and can cause leaking.

[@dreamagery]

I really appreciate your channel. These are great steps for me to begin. However, I am tired of paying for a mechanic and would rather put that money into my family's mutual fund. Hence, any tutorials on repairing a Jeep Liberty 2008-2015 would be ideal. They are scarce. Thanks in advance.

[@novemberecho71]

Untrue! Properly used its perfect I remember a technicien trying for 2 jours to pry out my pan as it was prefectly sealed with red paste!!

[@TaijiArban]

I know how you feel. 1AAuto is my #1 place for jeep liberty repair videos atm. They have videos for everything I look up from differential to waterpump to transmission etc.

[@anguslean4058]

@@novemberecho71RTV is far superior to a gasket

[@henrymcdoza3109]

Hello, I have a '02 Liberty 3.7 and I'm looking to do the Trans oil/filter change myself . how many quarts does the trans take and what would you recommend to make sure it has the right level of oil? thanks a lot !

[@1AAuto]

HI Henry, We currently do not have this data available to us. The dealership should be able to tell you how many quarts your transmission should take if you would like to do a complete fluid change. Hope this helps you out 1aauto.com

[@SulCoCrazy]

I have an 03 liberty. This must be taken to a shop with a transmission fluid machine. For the system to be maintained all fluid has to be pumped through.

[@Ap-nv1hk]

I also have an 02 jeep 3.7 i could tell u the quarts if your still wondering which i hope your not

[@feliperomo7534]

How many quarts did you use after all?

[@gavinwood1506]

After you add fluid and drive for a little bit to check it hot. Do you have to go through the gears again then pull the dipstick or just pull and check it?

[@1AAuto]

+Gavin Wood Thanks for watching! You would just want to pull and check it at that point, you don't need to go through all the gears. 1aauto.com

[@AnonymousMisspeller]

When I search 1AAuto for a transmission filter for my 2002 Jeep Liberty it does Not show the filter on the transmission in your video. Why?

[@1AAuto]

+UsaMan LikeJapanGirl Currently the ones on our website are the only ones we have available currently. Thanks for checking us out!

[@erickonassis6310]

How many quarts did you add

[@franciscomandel1026]

Can you send link to that exact combo pack

[@ruthmetellus7042]

What type of transmission fluid?

[@victorgomez4615]

A serious question guys, how many quarters of ATF should I pour to refill the transmission deposit?, because I saw the video and I saw this guy put just one of them

[@1AAuto]

+Victor Gomez This will depend on the specific vehicle. Thanks for the question.

[@victorgomez4615]

@@1AAuto I got a 2004 jeep liberty

[@1AAuto]

+Victor Gomez From online research between 4-6 quarts but check your owener's manual for the exact amount.

[@victorgomez4615]

@@1AAuto thanks guys, I like your videos very helpful

[@jacobe696]

so there is no drain plug?

[@sixstringbeauty]

My 07 Jeep Liberty does not have a dipstick.

[@quintenandjoannklonowski134]

The Driver lol :)

[@Pancakeater420]

Would this be the same process for the '10 liberty? Where did you get your dip stick from? Do you sell it on your website?

[@1AAuto]

+David Crownover It's applicable to years 02-07, but this may still be a helpful guide even if it's not 100% on par with the 2010 design. We sell the dipstick here: www.1aauto.com/transmission-oil-dipstick-dorman-917-327/i/1aemx00195?f=681770&y=2010

[@Andingo86]

Would this be the same process for an 07 liberty?

[@1AAuto]

+Andy We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

[@Andingo86]

@@1AAuto thank you!

[@Jah.Soldier]

How many quarts did you put into the dipstick funel?

[@alfierose]

I believe that when you remove the old tranny oil from the tranny oil pan and the take off the tranny oil filter...whatever comes out is pretty much what you replace back into the dipstick thingy.. If you're unsure how much you just drained just dump your old tranny oil into a gallon milk jug or a container with some kind of Quart measurement on it. After you get an idea how much you drained you are ready to replace the filter, clean the pan, scrape the old gasket gunk off, clean that nasty magnet then put it back into the pan, bolt the pan back into place also making sure you did not forget to position the gasket AND bead it with that RTV stuff. If you are still unsure how much of the old tranny oil came out, seek assistance from the eye doctor. Nah, just jivin'. You'll see what comes out, com'on. Then start your vehicle and measure how much you need (at engine HOT level). Add what was lost. Done. Drive. :) Just to be sure how much tranny oil is supposed to go into your vehicle, check with the manual as well, fluid section.

[@someleverpuller]

Alfies Designer Shoppe most dodges require you check them in neutral. “What!!!??, no way!!!!?” Go look at your dipstick and see what’s on it. Almost all dodge vehicles will show overfull in park....

[@job38four10]

Does trans get left in park or neutral for checking fluid level?

[@MrCrazyboys87]

Park

[@ronb493]

My 07 Liberty doesn't have a dip stick. Just a cap that says dealer only. Anyone know how to remove it?

[@johnbrissette3794]

it requires a computer reading from the dealer but most people just go to a junk yard and get a dipstick from another year and use that

[@malontaylor6741]

I'm having trouble finding my transmission pressure sensor circuit b it says does anybody have a visual for this?!

[@jondavis3582]

no gasket for the pan?

[@AA-kw4gs]

Hello how much the amount of transmission fluid in the pocket Commander 4700 Model 2006

[@1AAuto]

We currently do not have that information available to us. If you have a Chiltons or a Haynes manual for the vehicle, it should tell you. 1aauto.com

[@AA-kw4gs]

I have a guide to the amount I did not say I was a little kind only

[@AA-kw4gs]

Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Mopar ATF+4 Automatic Transmission Fluid Transfer Case (3.7L Engines) Mopar ATF+4 Automatic Transmission Fluid Transfer Case (4.7L/5.7L Engines) Mopar NV 247 Transfer Case Lubricant Axle Differential (Front-Rear) Mopar Synthetic Gear & Axle Lubricant SAE 75W-140 (API-GL5) or equivalent with friction modifier additive. Brake Master Cylinder Mopar DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only rec- ommended brake fluids. Power Steering Reservoir This system requires the use of Mopar Hydraulic System Power Steering Fluid (P/N 05142893AA) or equivalent, which meets DaimlerChrysler Ma- terial Standard MS-10838. 390 MAINTAINING YOUR VEHICLE Information Provided by:

[@amopastorcanadense]

Which oil i use for automatic gearbox?its Jeep Cherokee(liberty)3.7 4 automátic gears

[@TaijiArban]

ATF+4

[@BallRich]

How many quarts of transmission fluid did you use?

[@1AAuto]

Most passenger vehicles take from 12 to 16 quarts of transmission fluid, but the model of the vehicle dictates the type and how much. +Jeremy Richardson

[@darkdark4350]

@@1AAuto yes but How much for this particular change???

[@chessaudiobooks3079]

you guys carry the transmission cooler lines?

[@1AAuto]

+ChessAudiobooks Here is a link to the ones that we carry on our website. Hope this helps you out goo.gl/vsYdkZ

[@victorluiz2008]

I drive a 2011 Liberty. Same process??

[@1AAuto]

+Victor Luiz The installation process should be very similar.

[@victorluiz2008]

@@1AAuto Thanks!!

[@standardname1295]

Is this the same transmission as Dodge nitro 3,7 2008?

[@1AAuto]

they are not +Standardname

[@standardname1295]

1A Auto Parts thank you verry much for your fast reply

[@nextmichealphelps]

My 02 Jeep Liberty has a slight delay when switching from gear to gear. Could that be that i need to change my transmission fluid?

[@1AAuto]

Thank you for watching! It is possible the fluid level is a little low. If this is the case adding some or changing it altogether may correct the problem. 1aauto.com 888-844-3393

[@masonfarmer4653]

how many bolts

[@1AAuto]

@DeltaFoxtrotWhiskey3 The back of the owners Manuel will tell you. You could also try and measure the amount that comes out. Hope this helps! 1aauto.com 888-844-3393

[@andrewbarker932]

So we're just ignoring the instructions and not letting the RTV set before torquing the bolts down then adding the fluid? Wonder why so many people think RTV gaskets leak...?

[@blackshirej]

I was thinking that too...I remember the last time I did mine, you're supposed to only tighten til the rtv starts to squeeze out, wait x amount of time for it to setup and then torque them to spec.

[@job38four10]

Where is the freeken FULL mark on dipstick, all it says is cold and hot.................

[@fredmurray5255]

i use to work for a trans place and we all ways put a gaSKET ON THE PAN WITH THE GLUE TO HOLD IT AND WE ALWAYS FLUSHED THE OLD OIL BY REMOVING THE LINE TI THE RADATOR STARTED UP THE CAR AND PLACED IT IN TO REVERSE TO PUMP THE CONVERTER DRY - STOPPED THE CAR AND PUT THE LINE BACK ON TO THE RAD AND PUR NEW OIL IN THE TRANY//FRED NY STATE

[@g.t.g1111]

Than You!! The guidance was helpful. However, I made a mess!! 😢 Nevertheless, it’s completed. 😅

[@1AAuto]

+G.T. G 1 Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@driverman269]

I've used both permatex & gasket before!😳

[@davidibarra4947]

is it a 4x4

[@1AAuto]

+David Ibarra Yes this is a 4WD truck

[@ziadyassine335]

Hi, How do I turn off the 0/D OFF Light on my 2007 Jeep liberty 4x4

[@luisdaniel75]

Just push a little button on the left of shifting lever

[@carslover3509]

great job

[@christopherkiely8707]

Do yourself a favor.. Get a sucker unit.. Much cleaner job if you can have that pan empty before you pull it off..

[@anguslean4058]

Yep I have a MityVac got if off Amazon

[@mikehickman3635]

A pan gasket for this model is like 15 bucks just sayin. I am a firm believer in rtv my entire race bike moter is rtv except the meter gaskets I'm just sayin

[@jcnicework-jw3n]

👀👍 stairway soft

[@kallep1956]

Super alles gut erklärt 😀

[@1AAuto]

+Kalle P Danke fürs zuschauen. Ich wünsche ihnen einen wunderbaren Tag!

[@felipehernandez2994]

Sweet

[@1AAuto]

+Felipe Hernandez Thanks for watching. Please keep us in mind in the future if you need parts for your vehicle. 1aauto.com

[@zbow1974]

please stop telling people to use RTV alone, have them get the proper gasket and do it right.