How to check and change the swivel cable on Dolphin by Maytronics pool robot

Рет қаралды 43,635

2 жыл бұрын

Watch this short video to understand how to check and, if necessary, how to replace your robot's cable 𝗗𝗼𝗹𝗽𝗵𝗶𝗻 𝗯𝘆 𝗠𝗮𝘆𝘁𝗿𝗼𝗻𝗶𝗰𝘀.
By following the steps that our technician shows you, you will be able to carry out this operation yourself.
Procedure valid for Dolphin Maytronics Supreme, Explorer, Maxi Kart, F60, F50, F40, SF60, SF50, SF40, Kaptur, Pulit, Zenit pool robots.
🔧 All spare parts can be found at this link:
bit.ly/3JaX2n1
⭐️ Follow us to stay informed:
▶ Sito: www.zavattishop.com/en/
▶ Facebook: / zavattishop
▶ Instagram: zavattishop...

Пікірлер: 26

@earljurgeluks3387 Ай бұрын

I’m noticing different part numbers for different cables. How do you know which cable goes to your cleaner?

@zavattishopeng2733 27 күн бұрын

On our website you will find all the spare parts divided by robot model: www.zavattishop.com/en/pool-robots/accessories/dolphin-spare-parts.html

@TheOceanrainbow Жыл бұрын

After changing the cable, and put it to work my cleaner only stays on the walls of the pool. So you have any idea why it’s only cleaning the walls?

@zavattishopitalia Жыл бұрын

Hi, I can't tell you the reason for this malfunction. Are you perhaps using extension cords to power the robot? We are an Official Assistance Center, you can send us the cleaner for a check if you wish.

@angi4072 10 күн бұрын

Any tricks to plugging the new cable into the dolphin? I got the old cord out but new one doesn’t go in far enough to screw it on.

@zavattishopitalia 10 күн бұрын

Hi, you just have to push, there are no tricks.

@WaaayPastBed Күн бұрын

You may have the same problem as me. The new cable they ordered and sent me has two males but is missing the female hole. Essentially not allowing it to be pushed further down. The older one, has two males on the cable end but also a female hole allowing it to go over the top of the male counterpart built on the vacuum. Since the new cable doesn’t have the female hole, it will not work since it’s only two wires. I knew I should have ordered the part myself. Haha

@zavattishopitalia 38 минут бұрын

@@WaaayPastBed Hi, I don't think I understand the problem well. Can you send me some photos and the order number on our website? This way I will be able to help you by understanding what you purchased.

@rolandomota6919 Жыл бұрын

My wires broke at the 2 prong plug going into the power supply box. Is there a way to place the plug and use the same wire?

@piscinaonline.itzavattipis2163 Жыл бұрын

Hello, write us by email with a photo of the problem. So we will try to fix it.

@fireyourrocketts 9 ай бұрын

Well good video, mine is the E10 and I am completely disappointed and feel robbed by the manufacturer; that cable tangles in the water and do not let the cleaner work efficiently; they recommend to extend it in the sun but that does not works I watch painfully as the cable just wind into itself. The vacuum is useless with such a screwed up cable they use and there is no solution for this other than get rid of it. I feel feel suing the company!

@zavattishopeng2733 9 ай бұрын

I'm sorry about what happened to you. This robot model is suitable for small above ground pools with a flat bottom where the cable does not get twisted. If you have problems with the cable you can mount the anti-kink one: www.zavattishop.com/en/maytronics-99958906-diy-18m-swivel-floating-cable-for-dolphin-e40i-robot.html

@steveprice5664 9 ай бұрын

Something that doesn't completely solve the problem--but makes it a lot better--is to string a rope across the middle of your pool, sort of like segregating a swimming area from a diving area. Run the cord from the power supply, over the rope, then down into the water to the cleaner. For tangle-free performance, you would ideally want the power supply over the center of the pool, but that's not feasible. Running the cord over a rope is fairly close to this.

@zavattishopeng2733 9 ай бұрын

@@steveprice5664 this could be a good idea but the best solution is the swivel cable.

@fireyourrocketts 9 ай бұрын

@@steveprice5664 I resolved it now by running the cord inside a 25 ft pool vacuum hose, the inly tangled part is the little section of cord from the end of the hose to the Dolphin; now it reach all corners, still have to run it several times but no more tangling; that cord and the way it is made just sucks and cheapens the vacuum; I have always felt robbed with it, mixed feelings of it and some satisfaction sometimes; lets not forget the super fine cartridge is an extra almost $100.00! for what they charge we should not have to be writing here trading ideas

@CeciliaPavlacic Ай бұрын

I can't get the plug to pull out. Any suggestions?

@zavattishopitalia Ай бұрын

Hi, do you mean you can't detach the cable from the motor?

@__Brandon__ Ай бұрын

You have to pull harder than you'd expect

@thatguy3468 11 ай бұрын

When showing the swivel connector, please show it. Flashing it by moving the camera doesn’t help.

@zavattishopeng2733 11 ай бұрын

Good morning, thanks for reporting. We will improve in the next videos. If you have difficulty in the replacement we can hear each other via whatsapp for support: +393341491755