How to Check SMD Resistors Good or Bad

How to Check SMD Resistors Good or Bad
#electronic #electronics #shorts #electronicsabc
In this video, you will learn about smd resistors, how to check smd resistor with digital multimeter, smd resistor code, smd resistor testing, smd resistor check multimeter, smd resistor testing multimeter etc.
#resistance #repair #resistors
Song: NIVIRO - Flares [NCS Release]
Music provided by NoCopyrightSounds
Free Download/Stream: ncs.io/Flares
Watch: • NIVIRO - Flares | Hous...
Thanks
electronicsABC

[@rishanranatunga4851]

You should have mentioned, that the valve of the resistor code 203 means 20000 Ω or 20KΩ

[@จิงจิงก้อชอบ-ฐ1ห]

20=20+000=20k ฉันเดาว่าอย่างนี้🎉❤

[@tranvannam98]

​@@จิงจิงก้อชอบ-ฐ1ห is 20 and 3 zero 😅😅😅

[@hanamihana349]

Tyvm

[@AIexanderHartdegen]

you forget a 4th measurement. The resistor can be connected to another component and can shows a lower value than 20K.

[@mohammed-hy4um]

203=20,000= 20 K ?

[@electronicsABC]

yes, last number of any smd resistor code represents number of zero

[@andrewkiiza364]

So u mean if it's 201, it means the value is 200?

[@electronicsABC]

@@andrewkiiza364 yes

[@rajeshmobilesolutions8336]

20(3) 3=000 20 000/k 20k oms

[@techsartamil4529]

Resistors Fault. 1. Open. 2. Value increased. 3. Never short except wire wound resistors.

[@Seba_World]

I'm learning electronics too. If i'm not wrong, we can mesure resistors on PCB (unlike Capacitors). Hi from Poland.

[@orange_tweleve]

​@Seba_World yep . Capacitors it's hard to know where it's connected. But you can check the capacitor to see if they at least show a reading since dried out caps don't show any reading.

[@nelsonnuevo4168]

what about if the value of the resistor is decreased its also consider as fault resistor?

[@albastuzjosee9485]

​@@nelsonnuevo4168 yess if value increases, it's faulty

[@mohanv9483]

Hai sir this type all components cheking videos pls

[@CM-xr9oq]

What?

[@mattb9664]

The third one is the same problem I'm having with a resistor in a pristine, $10 Tivoli Model One radio I got from eBay- it's a 2700 ohm resistor that is measuring 4M out of circuit which is causing the downstream amps to misbehave. I'll find out tomorrow when my resistor sample pack comes.

[@spicky2966]

mines beeping in circuit hummm..

[@ismaelkangulu8662]

I am electrician, but I wanna learn about electronics, Any recommendations where I can start on the internet

[@frankalabastro2664]

Not possible on third one unless somebody sprayed salt water orther conductive elements or fluids over it /carbon powder or wrong value resistor

[@kingsolomon1451]

Does it mean that none of them is good?

[@rpdmak9096]

On my pcb there is a smd written 470 which means 47 ohms. From multimeter its showing value of 48.5 ohm its good or faulty???

[@electronicsABC]

your resistor is not good

[@mrstanlez]

what about smd diodes as A21 ?

[@engemandarwish]

How to check it in the pcb ?

[@MisaelJefte]

The value can be diferent because of series and parallel resistors

[@Okbayweldu-xw4td]

Thanks for the information this can be very inmportant. for me to learning.❤❤

[@RetroMyBits]

Off circuit, what if they are in circuit ?

[@YtpremIum-eg1fc]

Nice tutorial bro ❤

[@electronicsABC]

Thanks ✌

[@MRlai13579]

Is this open circuit and high ohm problem ？

[@endurofan9854]

thanks bro

[@Kingkoo-r3r]

Please please send me more bro

[@juankmora8599]

Genial me encanta tus videos. Gracias por compartir

[@MZMY_PRODUCTION]

What unit to check? Ohm meter?

[@electronicsABC]

ohm

[@melmelcandry7911]

Thanks for the information...this can be very important for me to learning

[@electronicsABC]

Glad to hear that

[@bronisjonaitis]

P

[@trevorsmith5946]

resistors values are not always exact they all have tolerance levels or margin of error from the factory

[@eddiemanuelitonavarro2622]

That's because chips resistor are rated in rank no. Like the sample 203 that mean 20k 201 mean 200 like the capacitor

[@ErickSudrajat-vx2jb]

Tapi sayang saya tidak punya avometer digital karena kalau yang non digital saya kurang paham pembacaannya dan akhirnya menurun dan hilang minat belajar lebih dalam dan lebih kreatif ya mungkin untuk bantu istri atau orang tua saya yang makin menua..😢😢😢❤❤❤👍👍👍

[@pauldebruyn4389]

Must resistors be tested out of circuit (be removed)

[@musaedalhajj214]

What if the resistor value is 21Kom and it shows 22kom .

[@abdulmuhaimin342]

Capasitor how ?

[@alphacentauri4155]

all looks good.. but how does the resistor lose value?

[@usmanjibril7990]

How to tackle circuit influence in reading?

[@UrduAdab-yz8nd]

Third one is ok what the problem?

[@Chris-gy1hf]

Third one was bad

[@SunkanmiMaliege]

Wonderful i never knew this

[@Neuralcarrot420]

You should include you know the value of the resistor

[@electronicsABC]

This method is useful for measuring any smd resistor, good or bad

[@leothecrafter4808]

It's printed on with these larger ones

[@TheBypasser]

@@electronicsABC Lol. How are you supposed to know the rated value of an 0402 or smaller, again? ;)

[@Neuralcarrot420]

@@leothecrafter4808it’s printed yes and a tech or someone that knows can read it but it should be included what the actual ratings on data sheet are.

[@AgostinhoHermesschulucubier]

❤❤❤❤❤❤❤❤❤🇧🇷🇧🇷🇧🇷🇧🇷

[@高野真人-o9v]

原点地 ファン 起動

[@Tigrignainfotech777]

How about i buzer mode?

[@daytonagreg8765]

Power off to PCB board? #ImANoob

[@doctorpcsolutions993]

3xcelent

[@itzzamen3553]

Thanks

[@electronicsABC]

Welcome

[@rajesh4603]

If resister not good they will not show low resistance value

[@syriansayf]

What if the resistor is a low resistance resistor... 😂

[@syriansayf]

If the resistor is NOT good they will NOT show low resistance? So if the resistor is NOT good they WILL show a high resistance value? So if the resistor IS good they WILL show a low resistance value?

[@syriansayf]

😂😂😂😂🤣🤣🤣🤣

[@maven_grandprime]

yes thats correct👍

[@hopskustomaudio]

What if its showing a different value in a circuit?

[@SKLS-pq6wf]

nice!!!

[@dlavisual2385]

Ok

[@adamszewczyk8845]

All is nok

[@gorarokaya8385]

best of luck

[@jimmyrodriguezmartinez7222]

Y la de 200

[@shivshankarkashyap7802]

Nycc

[@JeffreTirao-s5e]

Nice 1

[@raeeskhan4371]

hi sir I have 473 ohms smd resistor I checked it has 46.4 ohms its work or no. and how much ohms is good for it. thank you

[@electronicsABC]

Actually 473 ohms smd resistor means 47K ohms. Remember one things that damaged resistors don't show shorted value (46.4 ohms). If Meter shows between 46.8K to 47K then it's okay

[@raeeskhan4371]

@electronicsABC thank you sir

[@salh2665]

❤❤محتوى يستحق الدعم ❤❤❤

[@pallabbiswas8764]

Ok resistor good

[@cmntkxp]

Incomplete information.

[@electronicsABC]

next time i will try my best

[@GCS88]

So does the third one mean that a higher voltage (signal) can pass through intermittently?

[@Chris-gy1hf]

Yes

[@Chris-gy1hf]

Yes

[@antoniorobertomianmian4287]

3

[@m.b.anjaneyulu]

Wow😮😊

[@eletronicoseletronicos8893]

Resistor 2 está aberto e o 3 Alterado

[@electronicsABC]

its an example

[@trinkaiser365]

music?

[@electronicsABC]

see description box

[@TheGadgetklinik]

Thanks for the information

[@funboxeverything3677]

😊

[@Jeff-t1m1i]

That is not a stator y can't ANYONE TELL ME ANYTHING

[@enver5246]

😍 مهندس

[@noobcube48]

He playing guitar 30 hours a day every day

[@PardeepSingh-ut3wh]

Plz measure with high accuracy multimeter like fluke

[@hamdihamdy1156]

Fluke is one of the most expensive devices , accurate and durable .

[@kjellrogerjgensen60]

I dont thinc Fluke nececarily is better but they do keep their models over many years so de industry dont have to adapt to new routines all the time. That saves them a lot of money. Fluke does take charges for that service fore having conistency in ther models. Thats what you are paying for.

[@abdullqahar7359]

❤

[@BigTurtleMane]

“SMD” resistors 😂

[@tvoovm7254]

But they are smd resistors.

[@BigTurtleMane]

@@tvoovm7254 idk about u but I usually kick SMD resistors out and call another girl 😏

[@pamelarivera2889]

Did not explain the reading values. No knowledge imparted

[@sathiyavarathan-yothananyo8350]

What happened to 3rd one? 203 = 19.97k ohms = 2.059m ohms.. Its correct or not?

[@nilesh_145]

Nice editing real y nice editing ❤

[@supriyono4723]

Alhamdulillah For Everything

[@scorpion7biss]

Oui mais en test sur circuit la valeur peut varié en fonction des autres composants qui y sont relié

[@surasaidnakphalang4724]

😅

[@mubasherburki2634]

Transistor check

[@electronicsABC]

coming soon

[@rudeus6088]

Very useful info, Hope you make a good info like this in the future. 👍✅