HOW TO CONVERT DUAL MASS FLYWHEEL TO SINGLE MASS | DUAL FLYWHEEL PROBLEMS & SOLUTIONS | AUTOKRAZE

Hi friends, in this video i have shown how to convert a dual mass flywheel to a single mass unit. I had been facing a lot of issues with the stock dual mass flywheel as it had gone completely bad. Here, in this video you will get to know how to diagnose a troublesome dual mass flywheel and also how to fix it for free without buying a new unit. I hope this video helps. For any queries kindly coment below.
Also, i have a related video for dual mass flywheel noise identification. Kindly refer to it for further help. Link is below :
• HOW TO IDENTIFY DUAL M...

[@cameronwilson9193]

very smart man thank you for sharing

[@spencermoore2468]

The flywheel will now be out of balance causing lots of vibration which could end up breaking the crankshaft.

[@SyedAli-ny1yq]

Wow that's an amazing video. Amazing thought👍

[@Autokraze]

Thank you so much😀

[@MichaelBrown-bt6hr]

Man this is some real shade tree stuff. I'm sure the the flywheel wasn't balanced but hey he's riding.

[@ferraribhoy5799]

Be much easier to put a SMF onto the crank, and go back to a traditional arrangement. How did people manage before DMF were fitted?? This guy has hillbilled this clutch to work (and it does) so respect goes to him (if he couldn`t convert it back to a SMF since it was off.) Obviously he did it to get him or a friend back on the road, at some point the disc will need replacement though.

[@jadesantos6256]

Hi..after converting the dmf to smf by welding together..is it necessary to grind the welded portion by turning it to lathe machine...is it also necessary to balance the flywheel?

[@Autokraze]

No its not necessary to grind the welded portion unless it comes with contact with anything i.e. no friction with other parts. And how do you plan to balance the flywheel? You need to spot weld the DMF at points with equal differences; you can measure the point differences for weight difference caused due to welding. I hope this helps😊

[@bladder1010]

Now you're going to have super-harsh clutch engagement. Here in North America there are often single-mass flywheel / clutch conversion kits for this issue. Instead of the damper springs being mounted in the flywheel, they are back to being mounted in the clutch friction assembly in the traditional way. I assume you only did this as an experiment?

[@Autokraze]

No conversion kit was available here and being the cost of new flywheel too high, i was left with no other choice.

[@laurencecore]

What kind of clutch disk did you pair with the flywheel?

[@Autokraze]

The same disc which came with the car. Modified clutch with springs is unavailable here in India.

[@nonoypolison976]

Dude did you try to run your car for many mile, is your engine or transmission did not find any trouble. I have also a problem with my sorento DMF it hard to find the part here in the pinas.

[@Autokraze]

Yes, it seems to work fine but in the long run it will affect the gearbox's top shaft bearings due to vibration.

[@rommelekstrom1973]

Sir npagawa nyo ba yong DMF Ng car nyo to single mass flywheel,balak korin pgawa yong sa grand starex ko

[@rommelekstrom1973]

Good day ,idol can i do the same what you did conversation to my grand starex d4cb crdi , 2011 model and how's your conversations to your car its is ok until naoet

[@Autokraze]

Well this is a cheap way to run your vehicle when the dual mass flywheel has given up. The con is that you have to keep the rev band low as increased rev will cause more engine vibration which will in the long run cause harm to the gearbox as the converted single mass flywheel will not be able to dampen the engine vibrations.

[@jadesantos6256]

Hi..did you take out the inside parts components of the dual mass flywheel?

[@Autokraze]

No, just welded both the masses into a single one.

[@jadesantos6256]

How about balancing the flywheel, is the balancing needed...

[@jadesantos6256]

turning the flywheel to the lathe machine to take out excess weld and to make also perfect circle..is it necessary/needed?

[@Autokraze]

The objective here is to control the engine vibrations and dampen it not balancing, the flywheel and clutch absorbs the vibrations. In a DMF vibrations are absorbed by the flyhweel and in a SMF the clutch disc does the job. If you convert a DMF into a SMF be ready to endure more harshness and vibrations.

[@legitimacy3848]

can i do conversations on audi ack engine from mass to single clutch

[@Autokraze]

Yes you can. But I suggest you go for an aftermarket conversion kit. Should be rather cheap than OEM ones.

[@yourchoise7186]

i got it for 19k luk original dual mas fly wheel dsg 129 teeth.

[@edward0tunga743]

What about power

[@janardhanrao8948]

How to do it fir Chevy cruze

[@Autokraze]

Process stays the same.

[@cocomonkilla]

if you don't know enough about cars to realize this video isn't specific to any make or model then you really shouldn't be attempting to do anything shown in it

[@zitro_daddy]

A year passed, may i ask if the car is still alive?

[@Autokraze]

Yes, it is

[@zitro_daddy]

@@Autokraze thank you

[@3dprintfactory482]

It’s probably not square or balanced

[@basheertsm7900]

Your sound system is very faint

[@4RMS7TRONG]

Fucking hell... What a mess 🤣you know flywheels have to be balanced right? You've unbalanced that one.

[@datco4507]

The engine will get fucked up.

[@Nk-di6ef]

Now works good or bad

[@Autokraze]

Works fine