HOW TO IDENTIFY DUAL MASS FLYWHEEL FAILURE|CLUTCH NOISY|FLYWHEEL FAIL|AUTOKRAZE|ENGINE VIBRATION

Hello friends,
In this video i have tried to identify the symptoms of a failed dual mass flywheel and how to know. I hope you like this video and if you do; please hit the like button and share it. Thanks
Autokraze

[@prasen222396]

Very well explained in layman language .One of best blogger in india.You should post more such videos

[@Autokraze]

Thank you so much😊

[@dylanknight4752]

I figured my Ford was the dual mass flywheel failure, but wasn’t 100%, this video makes me feel a lot better that it’s not a bearing issue! I got 100k mikes out of my dmf so I can’t complain much!

[@chippywarren9706]

Very well presented. I have a ticking type sound which goes away when the clutch is slightly pressed. But I also have random rough idle on my Patrol. Thank you.

[@Autokraze]

It should be the flywheel, rough idle is a definite symptom along with clutch pressed and depressed variations.

[@philsteels]

Thank you for this video! My Kia Sportage sounds EXACTLY like this, at least I know what it is now!

[@Autokraze]

Glad i could be of help!

[@krunoslavnegulic9939]

Very good, you can also feel DMF failure on your clutch pedal in neutral. Press halfway down, and if you feel subtle (or less subtle) juddering (or 'jumping' ) of the pedal, it is clear sign that the flywheel is by-by. Change it, as it can cause cranck to brake.

[@aluyal9288]

Hi I have also car with dual mass flywheel My problem is after 20 min of driving the gers go dificult to change and 2 and 3 gear is sticking... Du you have any idea please I change the oil in transmission still same problem Manual transmission please if you know what can be the problem

[@Autokraze]

@@aluyal9288 No flywheel failure will not result in your gears sticking as such. You can change the clutch master and slave cylinder and then draining the brake oil/clutch oil and replacing it with new one. Hope this helps😊

[@jyotimishra4342]

Tamam. I feel so grateful tur gyanor karone. You saved our lives!!!! 😁

[@DaleSix66]

Just gone through a dual mass flywheel replacement myself. Lots of deep knocking and mid-range cracking sounds when the clutch was depressed. Turned out the plate had completely sheared off it

[@arekklampis9849]

Thank you,dude I'm from Indonesia..

[@montfrypan5904]

yes is usefull, thanks for share

[@Irianeth]

Very good video, thank you !

[@ionutolteanu5212]

Thank you, my friend, for explanations!

[@cimamaco]

Thanks bro my car is in the mechanic the first one told me that my engine was damage and the second one told me it was the flywheel

[@Autokraze]

Glad you liked the video. You can also temporarily convert the same damaged flywheel into a single mass unit. Should be cost effective.

[@mototommy5525]

@@Autokraze how? Weld it ?

[@t58beare]

@@mototommy5525 Don't.

[@babanfatih4926]

Brother I have a problem in my Chevrolet impala 2015 I changed injector and sparkle plugs and fuelpump Stil I have vibration in rpm 1500 to 2000 Even car transmission in natural When the car in the hills vibration increase Thanks for your help

[@gerarddonovan8678]

That sound at start up...exactly like my problem...thanks

[@thekeeperob]

thanks for the video

[@zizogaucho9035]

These are so common in vw diesels, driving me crazy

[@Smith6265]

Just asking a question !!! can you hear it more when you’re at 30 mph to 40 mph?

[@zizogaucho9035]

@@Smith6265 not really, i only hear rattling noises when it's cold and idling, it quiets a bit after a while. when moving, i only feel it in the clutch pedal, but not for long. Ps: it can get louder and louder by time.

[@chemicalyinbalanced]

I believe mine has gone. Could this cause a dip in rpm at idle, exspecialy after tapping the gas pedal? Also A "stutter" when starting. Thanks for the video

[@Autokraze]

Yes, the car will rattle more at idle and the vibrations will be felt more. As you progress gaining speed from 0kmph you will feel the car is struggling a bit to pull.

[@rodneytrotter8819]

I have the similar engine sound when I accelerate, although it's quieter when warm. Gears and clutch still feel good. The noise is unbearable. Did think it could be the gearbox but now you have me thinking. Kept losing power so changed the glowplugs, its better but not 100%

[@Autokraze]

The sound should be more when the car is idle and below 1500 rpm. If the noise is audible above 1500 rpm then reason could be something else

[@leeman2497]

I had similar noise on my audi q3 at 87k. Took it to a clutch specialist (not audi) was told same thing flywheel. If I got it fitted by audi £1800 , I ended up getting it done by specialist for £1200. 😭 .Car has been running sweet since.

[@peterparish1145]

Thank you

[@svmbaddie]

Hey, I drive a Jeep Compass 2.0 Multijet manual so I have this aggressive sound on starting the car and vibration whenever the engine is running / revving. Additionally on going in the reverse gear, it struggles to move from idle. Could the problem be the flywheel?

[@Autokraze]

Well the flywheel will give vibration only when the clutch is released. The jeep compass has a knocking sound when starting which is normal in it.

[@ElJaviTuning]

Hey, I have a noise on cold starts. When it sounds like the flywheel, but when you press the clutch pedal, the clutch release bearing sounds, but it only happens on cold. when the car get heat. it just doesn't sound anymore. What could be the problem? It's a 2.0 TFSI audi 8p 6 speed manual

[@Autokraze]

If it's the flywheel then after pressing the clutch, the sound should go away. Also, the sound of the flywheel is much more than that of the release bearing. Also, on cold start an engine generally sounds more than usual and if it goes away after the car gets heated then there is nothing to worry about. First, i suggest you check whether its the flywheel or not by depressing the clutch

[@ElJaviTuning]

​ @Autokraze When I press the clutch pedal, the sound it's only the clutch release bearing sound, but it goes away when the car get heated.

[@Autokraze]

When you completely press the clutch and the car is cold, is there any sound?

[@ElJaviTuning]

@@Autokraze Yes, the clutch release bearing sounds, but only when it's cold.

[@Autokraze]

Well in that case, i would suggest you to change the bearing else while on the run the clutch might give up. Hope it helps!

[@vinabakteir7665]

My hyundai i30 7speed automatic make same noice is it just flywheel? Not clutch? And easy to change?

[@Autokraze]

Automatics have a different mechanism altogether. It's not the same as manual. Moreover I doubt the i30 has a dual mass flywheel. Sound should be from something else

[@rishipithwa3531]

I have a 2.0 TDI A5 2015, this only does this occasionally after driving in slow traffic. Rattle sound when in neutral and when I depress the clutch it rattles. Is this just the fly wheel? It goes after I leave off in first and only does this occasionally not all the time. Any help appreciated

[@Autokraze]

Does the car vibrate a little in crawling speeds? If it does and there is a shake/jerk on acceleration from stand stop then it should be the flywheel. When in neutral you can open up the bonnet and observe exactly from where the sound originates. But without properly looking at it it's pretty hard to tell. I hope it helps

[@DilavarHuseynzade]

@@Autokraze hello, I have manual 5 speed, 1.6 TDI diesel. In my car in low rpm’s between 1000-1500 car rattles/vibrates. This vibration rezonates and drives me crazy. Thats why I am trying to drive in higher rpms. In that case it does not give any rattle or vibration. Can it be from clutch?

[@bangonfishingadventures]

can this destroy the motor at all Ive done a rear seal, then the clutch is going what next

[@richardwallinger1683]

My 2008 Lancia Musa 1.3 multijet 90 hp diesel engine has the same issue .. but the car dealer who sold me the car claims that he has documents / paperwork showing that the DM flywheel and clutch are new . I have inspected the gearbox mounting bolts and they look unmoved . how can I get my money back ?

[@Autokraze]

First off you can check the mounting bolts, a fresh bolt will look new and there won't be any markings on them alas they changed the bolts with new ones. It's very hard to reclaim from a dealer coz he will know how to deal with these kind of problems but you can claim through the paper work that if the parts are new then why the fault? The only way out is through the paperwork that he has😊

[@hemantpawar334]

Hello bro, Exact same noise is coming from right side of engine bay of Ford Fiesta 1.5 TDCI 2012 model. Will it solve after replacing flywheel.

[@Autokraze]

I don't think that the noise will be of the flywheel. The ford 1.5 TDCI has a single mass flywheel not a dual mass unit. Try pressing the clutch and observing differences in the sound and let me know if there is any.

[@McAmber]

Hmm, I don’t know about my vw golf mk6 1.6 tdi, not sure it has the same noise when its in idle

[@Autokraze]

If after depressing the clutch, the noise vanishes then it is the flywheel.

[@GloryXSniping69]

Hm. I thought my flywheel was going out but now I’m not so sure. I hear a weird metal ticking sound only when downshifting from 2nd to 1st. Also after driving for awhile and the car gets hot, it’ll have trouble starting once, then it’ll start up like nothing happened. Any guesses guys? It’s a 2013 VW Jetta Gli

[@Autokraze]

It's probably not the flywheel. You can check the Clutch cylinders both master and slave. Starting trouble is not related to clutch I think, trouble should be elsewhere.

[@Mad9john]

Guys can a flywheel or clutch also make noise under accelerating?…I also have vibration at idle and rattle of flywheel….

[@Autokraze]

Yes it can but the noise will not be so prominent while accelerating.

[@jonyy2196]

Hi bro,.my issue is ford ranger t6 automatic 3,2xlt,year 2015. when i drive so long far away,something sound from gearbox come out like tek,tek,tek,,but if engine like cool,,no sound can listen,normal sound only,may i know what is the problem?tq

[@Autokraze]

It is very hard to tell without actually seeing it. Are you sure the sound is from gearbox? It could be from the drive shaft as well.

[@jonyy2196]

Sure sir,comfirm sound from gearbox

[@Autokraze]

I can't tell without seeing. Is it possible to show me a video, i could try to tell from that

[@hoolahoola8194]

I have Hyundai Santa Fe 2006 dealer asking 6000 aud to replace dual mass flywheel and clutch

[@Autokraze]

Don't replace in dealer. Visit am independent workshop nearby and ask for their quote. Should be between 3000-3500 aud.

[@KOSTAS03051982]

I had only the noise at the start and my clutch it was very soft, it is flywheel? I have a Hyundai i40 2016 1.7crdi

[@Autokraze]

If it is the flywheel then the sound should go away as soon as you press the clutch. If the sound is way too loud and is audible even after you roll up the windows then it might be the flywheel. Else, it just might be the release bearing/cylinder.

[@raoofkhan8232]

Soo did it turn out to be the flywheel ?, I had the full clutch done including slave/master cylinder and release bearing now after 20,000 miles I'm having similar issues like yourself. I think it because of cheap quality flywheel

[@Autokraze]

Yes it was the flywheel. I will upload a video shortly relating to the conversion of a dual mass flywheel to a single mass unit.

[@Smith6265]

As much as you don’t want to pay the money👌🏻 it’s always best to take it to the main dealer for a flywheel and clutch even for a Timing belt water pump😀

[@milan-silviaderby4063]

Hello i got this on passat b5.5 can i drive with this and sometime i cant put gear

[@arronbatchvarov5035]

What noise can you here man I have small clicking when my clutch is up

[@Autokraze]

A bad flywheel will not affect gear shifting. I think you should check your clutch clyinder/master cylinder first and then the release bearing assembly.

[@andrewwelsh2797]

change the lot.

[@anthony6006]

I have a mk6 vw golf. My clutch pedal is hard to press and when i drive in the summer, clutch pedal makes a squaking noise. What could it be?

[@Autokraze]

If the clutch is hard, first try bleeding the clutch cylinder. If pick up is unaffected, then your clutch disc is okay. Try changing the master cylinder/release cylinder and if the pick up has reduced then you need a clutch overhaul and that should solve the problem. Let me know if it helps😀

[@grazianolaudisio3644]

After 21.000km? That's not normal!

[@ghassaneibrahim2491]

exactly my thought, it must be driven by many people..

[@xairforcex1301]

Did the sound go away after changing the dual mass fly wheel? Bcz i have the same problemm...

[@Autokraze]

I actually converted the dual mass unit into a single one by welding both the flywheels together. The sound as a result, is now reduced by upto 60-70% but is existent. If you change the flywheel with a new one the sound will be totally gone.

[@xairforcex1301]

@@Autokraze thnx for rypling, i had changed my dmf with a new LUK one, but the sound didnt go away... i think i will change it to singel mass

[@Autokraze]

You can try the conversion of your old dmf into a single unit without much cost instead of buying a new unit and see if the sound goes away. I am uploading the conversion video very shortly, you can have a look and let me know if it works with your car 😀

[@xairforcex1301]

@@Autokraze yess, but if i weld it together like you... its it not gonna get unbalanced is it? Cuz i dont wanna spend much money either😂 youre the only 1 who has the same problem like me, i’ve watched whole YT😂

[@Autokraze]

No no it wont. I have uploaded the conversion video just now. You can have a look at it and let me know if there's anything.

[@allsystemsdownagain9553]

Can't hear nothing different. Diesel engines all make a lot of noise.

[@thanos9973]

Kada nebi pricao mozda bi meko nesto cuo

[@mastercng]

all I can hear is your voice

[@martynaskaunas7156]

21k km and it’s broken, someone abused it

[@user-sf5iq2fl1l]

Dual mass fucking sucks.

[@johnduggan7428]

Sounds like a load of shite to me and it not coming from the engine

[@garethb7741]

Can't hear nothing coz u talk to much!!!