FYI the threaded holes in the rotor are so you can use 2 bolts in those holes turn them until they stop on the hub and turn them more on alternate sides to pop the rotor off if it is stuck on the hub with rust. put a bit of anti-sieze on the hub centre so it will come off next time as well.
@loganjohnson4254 Жыл бұрын
The bolt sizes are M8 1.25 but the way
@DeejPorter Жыл бұрын
You’re the man JT TRYING to get into learning how to work in my own car/truck Was completely stumped in the Toyota brake and that I needed a tool so thank you for getting me through that!
@DeejPorter Жыл бұрын
On*
@JT-zn5mg Жыл бұрын
ill be making some more content of the scion, but I appreciate man, if I can help one person with these videos then that's all that matters.
@twoxtro2862 ай бұрын
Currently doing this thanks, Because now I know what to do in order to push the Pistons back on the rear
@FlavortownFreddy Жыл бұрын
Opened up everything inly to realize i dont have that winding tool..lol..but great video..will continue the project after getting that tool😅😂
@Alejoo_CG Жыл бұрын
Very informative video thanks man! Now a front brake job video would be nice too
@JT-zn5mg5 ай бұрын
Check the latest vid
@bobbg9041 Жыл бұрын
You really should clean off the rust, both on the caliper bracket and wheel hub, you also want to remove the slide pins clean off the old lub, and put new lub on them if you don't lub the slide pins the caliper could lock up on you and wear out your pads faster. Also put the pad retaining clips on the bracket before putting it back on the car. Toyotas dont have screws the hold the rotors on the lugs. Then can fit really loose it all the rust is gone a trick to keep them in place until you put the wheel back on is put 2 lug nuts on hand tight just snug. I watched this because my 2012 scion tc will be my first set I've ever done rear brakes that use a e break built into the caliper im used to drum e brakes not caliper type. I'll go buy the tool Amazon has a 22 dollar set harbor freight its 45 bucks they might have a cheaper option. On clean the rotors just hang them on the lugs backwards the flipt them over the screw holes do not matter, they are there to pull the rotor off the hub like you did. 2 or 3 types of pullers sterring wheel this would use or pully type not used for rotors you want the pulling force closest to what holding it or you can shatter a rotor its cast iron cast irons brittle. You need to keep the pull force at the hold forces.
@brokeandbored85 Жыл бұрын
Thanks this helped me alot
@JT-zn5mg Жыл бұрын
no problem man, glad to help
@kingmosesix43221 күн бұрын
Hi there, Whts the name of the part u rented from autozone ?
@modestnovice23207 күн бұрын
The threaded holes aren’t for set screws they are to run a built down to pop the rotor off. Great video though
@mercedesmorgan15 Жыл бұрын
I don’t see any links to the tools used.
@seth111yta16 ай бұрын
jack points?
@4ourr6866 ай бұрын
will 2010 brakes work on a 2012?🤔
@JT-zn5mg6 ай бұрын
I don’t think so, I think the bolt patterns are a little different but I could be wrong
@srt_bris_955810 ай бұрын
🔥
@Youtubespyonme5 ай бұрын
No lube the guide pins
@leroykidd74576 ай бұрын
The previous owner……”drove it like they stole it”…..LOL Maybe “they” did….????