How to Engrave Photos with a Laser | Using Lightburn and LaserGRBL

Рет қаралды 40,106

Күн бұрын

How to Engrave Photos with a Laser | Using Lightburn and LaserGRBL
In this video I want to show you how different settings in Lightburn and LaserGRBL will affect your picture engravement.
Shopping:
Laser Atzer P10 Combo - atezr.com/products/atezr-p10-...
All my tools, woodworking accessories and video making kit is now in one place for you to check out. These are Amazon affiliate links. With a purchase through this link, you get an awesome tool and you will support my channel without spending a penny more. As an Amazon Associate I earn from qualifying purchases, thank you for your support!
Link to Amazon is just below! Thanks!
Tools I use and recommend:
www.amazon.co.uk/shop/casualdiy
Shop on Banggood - www.banggood.com/custlink/DmK...
You can now support my channel via Patreon. If you feel my content adds value for you or its entertaining then help me continue to do so.
Any donations via Patreon are so much appreciated, you can find out more here: / casualdiy Thanks!
You can support my channel by dropping some change in the Casual DIY Tip Box. Thanks for your support!
www.paypal.me/TomaszFranczyk
You can find me on:
Instagram - / casualdiy
Twitter - / casualdiy
Facebook - / casualdiy
Etsy - www.etsy.com/uk/shop/CasualDe...
Web page - www.casualdiy.com
Email - casualdiyuk@gmail.com
#casualdiy #woodworking #laserengraving
DISCLAIMER
My videos are for entertaining purposes only, your safety is your responsibility. Please do not follow my actions if you find them unsafe.

Пікірлер: 30

@paragonn22 8 ай бұрын

Sir. I thank you from the bottom of my heart! For the first time, I'm consistently getting the results I longed for, over a long time. Thanks again Sir! Your effort and knowledge shared with the community is greatly appreciated.

@CasualDIY 8 ай бұрын

Glad that my video was some help 😁👍

@MCsCreations Жыл бұрын

Fantastic, Tomasz! Thanks for all the testing and comparison! 😃 It's really interesting how the changes in the software reflects on the wood! Stay safe there with your family! 🖖😊

@CasualDIY Жыл бұрын

Yes and this is just scratching the surface of all the options and setups 🤔

@MCsCreations Жыл бұрын

@CasualDIY Oh, I bet! The interesting part is that some of the results reminds me of modern art!

@riahon 3 ай бұрын

I had been using imagr with success when engraving on canvas and glass for negative imaging, but struggling with wood, until I saw this. Thank you.

@CasualDIY 3 ай бұрын

Glad that my video was some help 👍

@AbzentMinded 10 ай бұрын

I've got a big project on my hands engraving a photo, this video is very helpful! This will be my first photo engraving wish me luck

@CasualDIY 10 ай бұрын

Good luck 👍 it may take few trials and tinkering the settings so don't get discouraged if it won't come out perfectly in the first few trials

@AbzentMinded 10 ай бұрын

@@CasualDIY I appreciate it! Cheers

@barry.w.christie Жыл бұрын

Another great video (as usual) 👍 .... I think the sheer number of options for engraving a photo will be confusing for a lot of people ... especially the result when you change the power and speed settings! Is the screen output a reasonable representation of what the actual output will be for the given material or is it a more of a try it and see what happens?

@CasualDIY Жыл бұрын

I would say try and see what happens lol To some extent it will give you a rough idea but with the same settings the engravement will look different on ply, wood etc.

@CoupleofBunkies Жыл бұрын

We have done a few experiments with two different laser engravers to engrave pictures. We even used borax and baking soda tricks. Both at the risk of completely ruining the projects. We are still learning and trying to get the hang of our engravers. We have also used lightburn and laser GRBL. We like lightburn but our current engraver is not compatible with it. We hope to get back to lightburn someday. But we get by ok with what we have. We try to stay creative with our projects. We have not done a lot of videos on our channel on photo engraving because we keep getting inconsistent results. We are yet to tune in the settings to get what we want. We have observed that a diode laser engraves better than a CO2 engraver.

@CasualDIY Жыл бұрын

Well with practice come better results and knowledge 👍

@Dancopymus 10 күн бұрын

Hello teacher! I did a test, using the speed (suggested by you) of 6000 mm/min and, I used the "Gray Scale" but, it weakly marked the wood/MDF (10W laser). I redid the test, now using a speed of 2400 mm/min, still using "Gray Scale" but this time the image (photo) was not sharp. Shows the image as a cloud.

@CasualDIY 10 күн бұрын

You can adjust the DPI so more lines. Should make the image darker and more accurate

@ms.c.j. 9 ай бұрын

I’m a keen amateur photographer, pets & landscapes mainly, and testing out laser engraving photos to wood first. I’m debating how to maximise quality of the image before I even bring it in to Lightburn… Would increasing structure clarity be best? Using Snapseed and Procreate on my iPad.

@CasualDIY 9 ай бұрын

I don't think it will make that much difference. I would use Lightburn to make any changes to the photo.

@petertaylor123 15 күн бұрын

Yes, it does. Check out a guy who looked at this burning a koala onto a slate coaster. He explains it better than I will and he walks you through the whole process,but do a grey scale intensity test. This will show you what your laser tops out at. It's a scale that goes from 0-255. I get differences in white fromm 0% upto 55% power, then it's all the same. Then in imageR or inkscape etc, adjust your scale to whatever your laser will max out at. For me is about 0-175. You will be amazed at the result!!! Good luck.