How To Fix E02 Error - Lay Z Spa Hot Tub Hire | Hot Tub Fun | 01494 355410

[@milothechihuahuabrunetandmommy]

Thank you for sharing your information I appreciate it I am a new hot tub owner I got an intex inflatable hot tub pure spa plus I haven't set it up yet Because it's winter here in Ontario Canada so thank you this will help me out alot have a beautiful day God bless you always

[@Tracimoon2222]

Thankyou for this ☺️🫂 and your spa is so crystal clear 😮 mine is never clear 😢 Also is the flow meant to be really strong because I can just feel it. When I remove the whole filter cartridge it is quite strong but when I put it back on the flow reduces dramatically I find if l tighten too much it stops,bi need to unscrew a little ..😕

[@markallwood4519]

This video was a god send, about to give up in it and it was the flushing out of the pump that's fixed it! Thanks

[@tomi210210210]

Mine had a worn impeller shaft in the water pump. Replacing the impeller, or just the shaft should fix the problem.

[@sebastiangee335]

Great video. Hose into the outlets exactly what I needed.

[@wholelottabull]

The black flaps in the filter housing is what was causing my e02 error because they were restricting water flow. I pushed them down so they are under the filter top and no more issues and the water is beautiful!

[@dirkdiggler4860]

I took mine right out lol

[@thesmashdaddy5466]

Best video. Followed all steps. Mine been down for 2 months. Lol works great

[@RhesaPhillips]

Greg & I are new hot tub owners we have one from saluspa . We are getting the 02 error code and it’s only a few months old. Thanks for the advice

[@dirkdiggler4860]

Mine was new doing this first day. My problem was the filtre was screwed to tight. Hope this helps someone else! And i removed those black flap backflow things

[@Anotherdamnlolly]

When I watch this video at 6:35 you detach the pump and hardly any water comes out of the last large pipe. When I detach the pump (after putting both black caps on) tons of water is gushing out of the third pipe. Could this be my problem? What is causing it?

[@yannickmacht5717]

Omg somebody please answer this question because I have the same problem ._.

[@carriepeel7267]

Same

[@Automcanic]

That's a problem, in the tub itself. The big pipe is where the air comes out of the unit and bubbles into the tub. There should be a one way valve in the tub side so it doesn't let water out.

[@scottsparks5214]

​@Automcanic the new units have 4 connections

[@bretthudson4196]

Replaced the pump armature….was badly split. The magnet actually ruptured. But it hasn’t solved the problem yet and water is not flowing. Came on momentarily and threw the 02 code. Now it won’t work at all….comes on for a few seconds and then no codes, nothing. Have done several resets. Any ideas short of the pressure sensor which is my next guess. Ty

[@andrewrankine-hb8qp]

hi i had an error saying the pump was to hot. I carried out all the checks as per this video..the water is sitting at 27 deg and not getting any hotter..i also removed the pump insulation cover that was on it.. any ideas.. filter clean and renewed did wash out and resets

[@keljontor1]

Mine was only set up and running for 2 weeks and it has no pressure :(

[@Kgray0884]

Me too !! 😢

[@scottanderson7306]

When you get error E02, does it trip your gfci? Or is something else wrong with mine. Thanks

[@chrisandrews1888]

I keep getting the NO2 code. Cleaned the filter and still throws the code. Also changed the filter to a new one and still throws it. Kept the filter off and works and throws no code. What would be the cause of this you think?

[@karolinacyka496]

I have the same problem with mine. Took my filter housing off and no code seems to be popping up.

[@jasonmaddox9202]

I have the same unit , no debris , checked for air loc blower won’t come on? Any suggestion

[@ThatArtTeacher]

Very helpful, thank you!

[@badhamster1509]

Superb. Water level was slightly too low (slightly above the minimum line)...5 minutes later with the hose, and the level resolved the error code. Thank you.

[@markhenderson8130]

Hi I've a bent pipe ( the bottom one ) from the fillter housing to the water pump , can this be replaced?

[@fredeiseman7309]

I have the same problem what did you do?

[@bmonsterh8942]

Buy a copper pipe cut and insert that will open the bent pipe up and let water flow

[@dpettengill4052]

This happens to me during inflation of the spa. any suggestions?

[@matthanson4720]

Same, just got mine. Figure it out?

[@dpettengill4052]

@@matthanson4720 yeah it was because of the cold when the machine just can't think that is just an error goes to so we set it up inside until it got warm and then it was fine.

[@scotimotti]

Thanks for the tips.

[@coopsevy5664]

I've done all of these steps and still it's not working

[@lastanahoward8806]

Me too and this is our second spa. With the same code

[@brianphillips1691]

Thank you sir!!

[@stellabenson7222]

Do you know if you can purchase a replacement black rubber that is inside the filter housing? I've looked online but to no avail. I have the lay z spa Paris.

[@rodneywebb1986]

Hi I’ve followed all these but still E02 code. I thought it was a squashed pipe but I’ve sorted that. Could it be flow meters?

[@AngelaDuLac]

Have you come across any yet? I havent been able to find the stoppers either. So frustrating.

[@mikeshaver100]

I just got.mine yesterday and with the filter on it pops up that code take the filter off and it is fine is my.pump bad?

[@had6212]

I had the same problem, ive changed my filter for pantyhose, works a treat, change it every day or two

[@inthekitchen8842]

​@@had6212how do you put the pantyhose in there? Do you just make a ball??

[@jenniferpaisley9491]

Hi can anyone help me, my pump is only heating up to 22 Celcius then stops going. I've tried all the resets.

[@munhassan7840]

Great video thank you

[@marciashoemaker7823]

Had E02 error. Went to turn back on after changing filter n it will not unlock??????

[@zackreynolds21]

Have you tried holding down for a few seconds on the unlock button? It takes a few to work

[@had6212]

Got sick of the E02 fault, so, Pantyhose, change(throw away) every 1 or 2 days according to use. better flow and general better filtration.

[@sharontuckwell9391]

Hi my tub is not blowing the hot water out of the chlorine unit no water comeing out of it at all,any info please why thanks

[@jenniferpaisley9491]

Sorry what the heck. Is an impeller shaft. No tech person in this house 😢

[@bretthudson4196]

It’s the plastic vanes that make the water move. The shaft is a magnet and I just replaced mine bcuz it was badly split…but still throwing the E02 code

[@waidsworldofart5292]

I've had mine for 3 months and I tried all of these things- still giving me the E02 error code ...so sad. Does anyone know who I can call if the pump is bad?

[@tylerbukus1458]

If water is not coming out of the top filter, I could be the pump but chick to see if any water is getting through your filter. I got a bad filter in the mail, and it was not letting any water through it. We pocked tiny holes in ours, and it fixed it for us, but just small holes, it still needs to do its job and be a filter. Best of luck.

[@chrisparfel]

Nailed it

[@danielblair876]

Good video. Thank you