Our car has the same problem do you take the intake off or can you leave it on
@danielavalos773 жыл бұрын
You need to show people how you took the part off not just the fix
@expertnugget6 ай бұрын
Just a pull nothing special
@ratandjmt Жыл бұрын
Thanks for the video. It was exactly what I needed to fix my daughter's car.
@markdavila52972 жыл бұрын
So on the top connecting u just popped it bak in it s the one connected to the sensor that’s messed up rite or why did u have to do the top on to ?
@powderskihound3 жыл бұрын
Hey I'm working on this exact same problem. I can not get that upper lever (that has the ball) on the intake side loose to drill a hole in it. How in the hell did you side that off?!?
@billgoatgarage3 жыл бұрын
it's held on with a metal retainer washer you need to pop off before it slides off
@billgoatgarage3 жыл бұрын
just use a flathead screwdriver and pry the clip off
@powderskihound3 жыл бұрын
@@billgoatgarage the clip isn't a problem. It's getting the lever to slide off the manifold to be held in my hand such as you've done.
@billgoatgarage3 жыл бұрын
is yours severely rusted? it's just plastic on a steel shaft apply some penetrating fluid and get a screw driver behind it
@powderskihound3 жыл бұрын
@@billgoatgarage no it's not rusted. I tried this and that. It was being a bugger. To be honest prying on old plastic parts is kind of nerve racking. I ended up going out and purchasing a right angle attachment for my drill. Then I threaded it through with a super long set of needle nose plyers. Works good nice hack my friend! I wish i doubled up the thin wire I used but there's more wire of this bit breaks.
@ICExMikey Жыл бұрын
Look up intake manifold runner arms with brass ball. Theres a long and short one
@mikepruett17452 жыл бұрын
mine is stuck in one position ... new motor for it??
@bobbyperalta76123 ай бұрын
got like 150 miles in still says needs two more modules to finish driving cycle( O2 and EGR) smh, replaced arm and still get p2076
@sherylbradley44782 жыл бұрын
I just spent an hour trying to get this part on my car …. How did you reach in and easily pop the bottom in???? I have small hands and can’t even do it
@x.adam13 жыл бұрын
Can it be done without taking anything off but the tuning valve arm? I drilled a hole in the arms portion but can't think of a way to drill a hole into the receiving end due to the location and size of my hand drill. I already ordered the replacement part but need a quick fix until it gets here in about a week.
@billgoatgarage3 жыл бұрын
I had to take off the pieces to drill them successfully. the one part is just held on with a press washer. if you get a screwdriver you can pop the metal retainer off and slide the piece off the shaft it sits in. then just do your best to secure it after.
@pur3mind6833 жыл бұрын
@@billgoatgarage was this done without taking off the whole intake ?
@powderskihound3 жыл бұрын
@@billgoatgarage that lever connected to the intake doesn't just side off after popping off the retaining washer. 😒
@silentofhell4710 ай бұрын
What if you put a new one in and you still get the code ?saying intake manifold tuning valve stuck
@billgoatgarage10 ай бұрын
then your intake manifold is possible full of carbon and it is actually stuck. can you manually move the linkage on the intake manifold? does it move? is it stuck? the linkage could also be broken in the manifold meaning the arm will move but the actual flaps in the manifold don't.
@silentofhell4710 ай бұрын
@billgoatgarage I'll try it. Thank you. I really appreciate it 🙏
@silentofhell4710 ай бұрын
@billgoatgarage it moves by hand
@stephanieramos36492 жыл бұрын
We’re did you buy the part ?? I can’t find it anywhere? Info Please
@billgoatgarage2 жыл бұрын
I repaired the parts that were in the car.
@alyciad86082 жыл бұрын
I bought mine on Amazon Intake manifold valve running arm $16
@daviddoerr2982 жыл бұрын
@@alyciad8608yes ma'am, same i got mine from amazon, for $9, but also i found a 4-pack of these intake manifold valve runner arms for about $14. Did you have any trouble installing it? and did you also have a P0017 go off?
@ozzygallegos84872 жыл бұрын
How did you remove the retaining washer from the small arm?
@billgoatgarage2 жыл бұрын
just used a flat screwdriver
@jossuejjp3 жыл бұрын
What's the number part ? My is not broken
@mikepruett17452 жыл бұрын
how bout p 0328 knock sensor where is it
@kaziwill2 жыл бұрын
You were right about one thing. These things are JUNK. I have a 2014 Chevy Sonic and if I properly fix this issue, I will have more money in it than it is currently worth.. F that!! To anybody reading this, if you can hack it, get rid of your shit chevy and buy literally anything else.. Chevy has been making junk for almost 20 years now and it shows...
@jmasca05823 жыл бұрын
Thanks for the vedio!!👍🏻
@brucemcatee93102 жыл бұрын
We're do I get the part
@billgoatgarage2 жыл бұрын
I repaired the existing part from the vehicle no new parts were used
@alyciad86082 жыл бұрын
I bought mine on Amazon Intake manifold valve runner arm $16
@pur3mind6833 жыл бұрын
Did you take off the whole intake?
@billgoatgarage3 жыл бұрын
no I fixed it in car without removing intake
@pur3mind6833 жыл бұрын
@@billgoatgarage mine broke from opposite ends , you think can still quick fix it
@billgoatgarage3 жыл бұрын
yes the hardest part will be getting the metal washer off to remove the one arm. just pry it off with screwdriver and use glue or silicone to reattach instead of the metal washer
@pur3mind6833 жыл бұрын
@@billgoatgarage I was able to pull the arm off from the top and replace the control arm with a new one from amazon . i thought it was broke the ball wore out and popped out the socket i just popped the new one in , once i replace the control arm is there anything i need to do to reset the car?
@billgoatgarage3 жыл бұрын
shouldn't be just clear codes and you should be good
@MyIdiotissues2 жыл бұрын
It’s Smoking 💨
@jesuschristislord9150 Жыл бұрын
Matthew 6:19-21 NKJV "Do not lay up for yourselves treasures on earth, where moth and rust destroy and where thieves break in and steal; [20] but lay up for yourselves treasures in heaven, where neither moth nor rust destroys and where thieves do not break in and steal. [21] For where your treasure is, there your heart will be also.
@ImGerald3 жыл бұрын
My niece has the same car with the same P2076 code. The arm broke off, so I order a new arm and put it on there without any problems. Cleared the codes, and P2076 is still popping up. Throttle body cleaned also.
@ivanmoreno39182 жыл бұрын
It's the actuator..that part the arm attaches to. You can get it at a junk yard or on ebay. I bought one for $25
@ImGerald2 жыл бұрын
@@ivanmoreno3918 yeah we replaced that, but wasn't the problem. It was the computerized motor on the throttle body. Plus it kept over heating anyway even after head and gasket replacement. We just junked it.
@manianggueye91332 жыл бұрын
Comment il s'appelle le pies
@user-ep6wd7ip7v9 ай бұрын
Garbage cars my control motor seized up just left it like that ever since lol no point in fixing it won’t harm the car been like that for 7 years
@miguelvarela42273 жыл бұрын
Sejalonea cuando avanza que puede ser chevi cruzer 2014
@everberrelleza66032 жыл бұрын
Cual fue la solución a tu vehículo? Tengo el mismo problema!
@KASPERSKY7073 жыл бұрын
FCK gas cars and all the sh!t parts and sensors... TIME TO GET A TESLA!
@frankieavalanche1805 Жыл бұрын
🤣 good luck
@susancarpenter882011 ай бұрын
I hope you have researched how much it costs just to replace a headlight or battery in one of those things. LOL!
@KASPERSKY70711 ай бұрын
@@susancarpenter8820 8 year warranty on a Tesla battery!