HOW TO FIX SLIP / STRIPPED BIKE ENGINE OIL DRAIN BOLT AND AVOID ENGINE DAMAGE

[@nazishshaiikh1730]

Keep it up good to know information 👍

[@santoshbasnet550]

Hi,brother what is ur drain nut size , I have 2009 model fz16 being from Sikkim Helicoil fix aren’t offered by garage, could u kindly tell me the Helicoil size used…btw my drain bolt head size is 17mm, guessing the thread is M12. Reply will be highly appreciated.

[@ഷിബു-ശ1ഫ]

bro mine is also the same fz s as your same colour and same year.currently iam using motul 20w 40 mineral oil.but iam planning to upgrade the oil to fully sythetic motul 20w 50.my bike gone 25000 only.is there any problem while usimg fully sythetic oil.also mention which oil use are using and its grade

[@mksoulmate6038]

Please post slipper clutch review

[@sajet12]

hi..I have FZ16 the rear brake light switch holding Bracket is rusted..is it a part which we can buy or it has to be welded??

[@mariakdebom2941]

Very useful......good video

[@MarufurRahmanAbir]

Do you use 20w40 regularly or 10w40?? I have fzs v1 2013 model, and i'm confused which one to use regularly.

[@MOTOMENTOR]

I have used 20w 40 and 20w 50 which gives best result... don't use 10w 40 the oil is to thin and you will have a lot of issues.

[@arunkhatana721]

Ye shop kha hai bhai jha aapne repair kraya oil drain bolt. Address btaye plz.

[@vels_3]

hello brother can my hornet bikes oil bolt is not getting untwisted.. what should i do

[@sajet12]

Hi..I have done this but now the area near bolt has little oil accumulated..what should I do now replace bolt and vicer or any other solution to stop it??

[@MOTOMENTOR]

Yes try doing that if it still not fix use Teflon tape around the bolt.

[@syamlalsselvanose]

Bro please tell me the spring tread dimension for FZ V1

[@shaikhnaseem5953]

Good information 👍👌

[@khamkhampi906]

on my last servicing to the Yamaha company service centre they over tight the bolt and now while after removing the thread got damage and its loose so how to fix it back?

[@Prateek_Rathee2102]

Kya kia bhai?

[@mr_Solorider_46]

Yamaha recommend 10w40 for fz

[@MOTOMENTOR]

For my 2010 indian model they have recommended 20w 40 as per usr manual.

[@mattcorbin8179]

Bhai me to lut gaya es video ko dekne ke baad.😭😭😭

[@amareshaxn]

Same Bro 😢

[@nagababunaik8158]

Bolt size kirana and thread cutting material size be kirana use kardiya..bro

[@rohitdaashisode8218]

Sir mera Ek concern hai Maine October 2022 me avenger 160 CC kharida hai. Pehle servicing k time hi showroom walo ne uska drainage ka but improperly fit kiya to waha se oil leakage shuru huwa, mere complain k bad unhone waha dusra bada nut bithaya, Ab mujhe lag raha hai k wo mujhe aage dikkat dega servicing k time. To meri apse request hai k waisa hota hai to mujhe aage kya krna hoga please reply

[@MOTOMENTOR]

Aap tension mat lo agar abhi leak nahi horaha hai to.... future mai agar dikkat aati hai is video mai jo Maine karvaya hai vo hi karvalena extra threading karke. Showroom walo ne galat kiya hai jo mostly local mechanics karte hai... ye kam mostly showroom wale nahi karte vo b Bahar se karwate hai ... app chek kijiye aap ke area mai koi threading ya boaring ka kam kartha hai kya aur waha se ye karvaiye.

[@rohitdaashisode8218]

@@MOTOMENTOR thank you sir

[@rohitdaashisode8218]

Sir Mai legally unke upar action le skta hu kya? Kyunki meri bike abhi warranty period me hai, ya phir bike replacement ya engine replacement kuch Ho skta hai kya

[@amareshaxn]

FIR Karo MC Par

[@CaffieneToCode]

Where did you got it repaired man?

[@MOTOMENTOR]

I am from pune got this fixed near appolo theater.

[@amanchoudhary1614]

Hello sir meri fz v1 bike ha vo 90 sa uper nahi jati ha nahi pickup ha us ma ma kya karu

[@nileshkharade5066]

pune ka best service center konsa ha ? . i have to do engine work like piston, crank, front forks ect . so i want best yamaha service center. because in pimpri chinchwad service center work not done properly. so can u tell me bro please..

[@MOTOMENTOR]

My experience was good with monarch yamaha the one at Tilak road.

[@nileshkharade5066]

@@MOTOMENTOR thanks

[@nileshkharade5066]

i have fazer v2 and im changing clutch plate because my bike stock clutch plats are total finished. so i decide to install slpper clutch plate assembly of r15 v3 in my fazer v2. can i go for it or i will install stock one? . and slipper clutch of u r fz working properly or not😃. if it works well without any problem then i will think about that

[@technofun80]

Whats your opinion on slipper clutch? Is it working?

[@MOTOMENTOR]

Yes its working awesome 👌

[@technofun80]

@@MOTOMENTOR is there any engine breaking when we shift from higher gears to lower gears?

[@rohansurve8330]

Bhai oil nikalna nahi padega na and how much it costs

[@MOTOMENTOR]

When I went to get this work o already removed 50 % of oil... it costed around 350.

[@rohansurve8330]

@@MOTOMENTOR i have just putten new oil in bike 2 days back😔

[@MOTOMENTOR]

@@rohansurve8330 if you are using expensive oil you can drain it completely and reuse it later....... get a local oil for cheap which you can fill and then go to get this work done coz once you get this work the left over is sometimes which needes to be flush and belive it it takes 2 engine flush ro remove the partials and that to some of it is still there stuck somewhere in engine. Make sure to clean oil filter too after draining the oil.

[@wakeupdin]

Can we keep magnet inside Engine for like this small particles to attract !!???

[@Dinesh-Bhardwaj]

I think these are aluminum particle so won't get attracted.

[@AltafKhan-jw5yn]

Ha wo mene link dekha bhai thrred sprring kaha milegi itnabatado Bhai plz

[@MOTOMENTOR]

Mujhe b nahi pata abhi but once ill have any information ill update

[@wilanderphilips3762]

Price for doing the slip?

[@MOTOMENTOR]

200 to 300 rs.

[@homauankaber6047]

What kknd of mobel best i have rum now 50000+ great...??

[@MOTOMENTOR]

Are you taking about the engine oil ? If yes go for fully synthetic one the same grade with is recommended by manufacturer.

[@homauankaber6047]

@@MOTOMENTOR dada fzs v1 but i have use 10/40...

[@ridewithdeep3272]

Bro thread ka price kitna aata hai

[@shakilshaikh786]

Main abhi karaya ye pune kondwa main 150 rs main ysne thread karnese pehle grees lagaya taki tukde usi main chipak kar aa gaye

[@MOTOMENTOR]

Kondwa mai kaha par?

[@AltafKhan-jw5yn]

Thirred kaha milege

[@MOTOMENTOR]

Description mai link diya hu app check karlo

[@nurvousenergy7268]

Engine oil bolt khulte time silp kat gaya .. abhi wo khul nehi raha hain.. side pura ghis gaya .. abhi wo keise nikale ?

[@MOTOMENTOR]

Please go to an expert they will cut and remove it properly with drill or by welding.

[@nurvousenergy7268]

@@MOTOMENTOR iska new engine oil bolt milta hain kya?

[@MOTOMENTOR]

Ha milta hai ... yamaha service center nai to automobile market mai aasani se available hai 17 number ka hai sayad. App bus unko bolo engine oil drain bolt chaiya vo dedege

[@nurvousenergy7268]

@@MOTOMENTOR 12 number ka bolt hain..

[@MOTOMENTOR]

Ok.. mere replace kar ke kafi time hogaya.... which bike you own?

[@rohansurve8330]

Bro my also oil leaking from bolt

[@MOTOMENTOR]

Sorry to here that but please get that fix asap ...running low on engine on can damage the engine. So please fix it.

[@befikrepanchhi]

👍

[@madhabsharma2459]

Original ka jaisa hoga

[@MOTOMENTOR]

Yes

[@AltafKhan-jw5yn]

Aap ne thrred kaha banay address dijiye mobile no

[@MOTOMENTOR]

I am from pune aap kaha se ho?

[@AltafKhan-jw5yn]

Maharashtra aurangabad

[@AltafKhan-jw5yn]

Mujhe wo teping set chahiye

[@MOTOMENTOR]

Wait link provide kara hu description mai give me 10 mins

[@Drowning_India]

👍👍👌👍👌👍👌👍👌👍👌👍👌

[@sjr4689]

I have a same type bike serious issue . Pls share your ph no .i want to talk to you regarding this

[@MOTOMENTOR]

Bro Tell me what the problem is.

[@APHOMELAND]

not to see drain nut repair , just show engine oil .no...to subscribe sorry

[@abdulsamadmandli675]

Please post slipper clutch review