How To Heat Up A Nut or Bolt WITH OUT A Torch

In this video I show you how I heat up a bolt or nut using a method other than a torch. I show and use an inductive heater in this video to make a simple repair.
*Induction Innovations MD-700 Mini-Ductor II Magnetic Induction Heater Kit: amzn.to/2y3cWzv
*Induction Innovations MD99-660 Essential Coil Kit: amzn.to/2sTPqje
If an SMA Video has helped you out please consider giving using "Patreon" to help support us. The videos take real time to create and pull us away from real work that pays our bills. CLICK HERE: / southmainauto
THANKS A MILLION!!
--Eric O.
If you don't like Patreon feel free to use the "PayPal Me" link: www.paypal.me/SouthMainAuto
The South Main Auto Amazon Store: www.amazon.com/shop/southmain...
AES Wave Automotive Diagnostic Tools: www.aeswave.com/cart.php?m=af...
WANT AN "SMA" STICKER OF YOUR OWN!?!
Simply send and E-mail to [e-mail] including: your shipping address and e-mail address in the text, I in turn will send you a Paypal invoice for $5 each USA or $6 each international. Let me know how many you want and as soon as the Paypal invoice is paid I will ship them out ASAP! Thanks for your support of our channel!!
--Eric & Vanessa O.
Feel like sending some swag to SMA because you love the videos but don't know where to send it?
Just ship it here:
South Main Auto Repair
47 S. Main St
PO Box 471
Avoca, NY 14809
Disclaimer:
Due to factors beyond the control of South Main Auto Repair, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. South Main Auto Repair assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. South Main Auto Repair recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of South Main Auto Repair, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not South Main Auto Repair

[@SouthMainAuto]

*Induction Innovations MD-700 Mini-Ductor II Magnetic Induction Heater Kit: amzn.to/2y3cWzv *Induction Innovations MD99-660 Essential Coil Kit: amzn.to/2sTPqje

[@mbucky4221]

South Main Auto Repair man i wish i had that set of tools. Im 26 so id say im getting there lol

[@DieselRamcharger]

110 bucks cheaper on fleabay

[@icemule]

@@DieselRamchargerWhere defective parts are King.

[@jakubpawlowski396]

I do not think it is "rust", that holds the bolt... Think about it, how many times did You actually taken out a bolt with rust on the thread? and yet it is allways that part of the bolt, that wont budge. To my knowledge it is because of difference in steel grade between the bolt and the block of metall you screw it into, they expand/contract due to temperature change a bit differently, but enough to eventually lock the threads against each other.

[@WhiskeyRiverRifleman]

The mini ductor sometimes works to remove stuck lug nuts with out destroying aluminum wheels

[@dieseldaddy4205]

born and raised in my dad's repair shop/service station. we were the only ones in the area where customers would not only bring their cars,,but their lawnmowers,,motorcycles and the likes. there is something about how you look at a repair,,that reminds me a lot of myself,,being taught by my dad,,who was the absolute best wrench in the business ( rest his soul---he passed away 6 years ago). it's nice to see that there are others that actually FIX broken parts,,rather than run out and buy new. keep it up. loved the video. please make more.

[@rhdtv2002]

Frank Castronuovo sounds like your dad was an awesome man. hope to meet him on the other side someday

[@ElderlyIron]

"Toolbox full of tools and I'm here with a pair of pliers". I'm with ya!

[@ml2trick]

Best Auto Channel on you tube. I have been a Marine Mech for 30 years. You are a true Mechanic.

[@mopardave4935]

+ml2trick Excellent point, and I would say he is a true Technician. Diagnoses and finds out where the root of the problem is emitting from. Much respect! I've always been curious ml2trick about what you Maine Mechanics do on a daily basis. Im a flat rate line tech at a toyota dealership, but have an opportunity once upon a time to work on boats. How do you like it?

[@SouthMainAuto]

+ml2trick Thank you

[@tomwyrick2824]

That's really cool! I've worked in industrial environments for years and I never saw a portable inductive heater before that's pretty sweet!

[@brianbanks3044]

ahhh, the infamous inductor....i just came across your video...i used it at my truck shop....COTTER PINS were my kryptonite but this tool saved my job and many hours of stress.....when you have a $200 tie rod end with a rusted solid , broken , frozen cotter pin, the inductor does the trick with out frying the bushings inside the tie rods....great tool and great video

[@jamespatton3720]

Very ingenious way to make a fully threaded bolt, Eric you are the man 👍

[@sporty196071]

I've been a mechanic for 45 years, you do a great job explaining and showing how to do things. I am old school and still learning alot. You've shown me tips and new tools. The future is in knowing electrical. I'm pretty good with electrical but not on your level. Thanks for all your help!!!

[@ernestbrown6766]

very good videos using excellent diagnostic reasoning and skills. About 1960, the late Neil Houston, co owner of Houston Brothers Motor Co in Marshall, NC, showed me his method of loosening rusty bolts/nuts. Once the piece is heated to cherry red, if possible drop item in a bucket of water or quench immediately with water hose. Then instead of squeaking as your bolt did, once loosened 1 turn, you will be able to screw bolt out with your fingers and the rust will fall out as black powder. Keep up the good work

[@RickaramaTrama-lc1ys]

Great video and you have the perfect attitude for a mechanic because patients is definitely a virtue when a person works on people's abused cars for a living.

[@wysetech2000]

20.000 subs. That's amazing and well deserved. Part of being a great mechanic is knowing how to get yourself out of trouble quickly and successfully. And no Brake cleaner either. Having the right tool for the job helps too.

[@mikedesjardin2515]

Thank you for the threading idea. I was working on a side by side with a missing long 3/8 nf thread and never thought about using my thread chaser that way and now the machine is up and running. Love your trouble shooting ideas and keep them coming

[@will104107]

I can't thank you enough, I spent about 2 hours doing that exact same job making a fully threaded bolt for a similar tensioning setup on an excavator never thought to put the die in the vise and use a drill I cut aver 100mm of threads with the die holder. thanks for the future time saver

[@Cockeyed0ptimist]

I don’t even work on cars and I enjoy watching this guy.

[@deanh7190]

This type of technology would have made the old board game 'operation' a heck of a lot more exciting lol. More seriously, watching you pull out specialty tools from that nice toolbox gave me the idea that shops should post up on their LABOR RATE sign, the amount of $$$ spent to date on proper tools, along with the shops annual overhead expenses. May have folks think twice before complaining about the high labor rates and they made be surprised at how much investment capital is at work keeping their cars safely on the road.

[@ronlapham5508]

Thanks for the help. I’m trying to break loose bolts on break caliper and wheel bearing. Ordered induction heater rather than flame by gas tank. Safety first when working at my house. Thanks again!

[@davidschwartz5127]

Also a terrific tip on adding an additional thread to a bolt, I have a method but yours is far superior! Great information, if now I can only remember it.

[@oldoldpilgrim7898]

South Main Auto is my favorite stuck bolt channel.

[@Sandbag1300]

Another thumbs up SMA production. 12:04..best.."something like this runs off of household current and it is relatively safe until it is not".

[@SouthMainAuto]

+Sandbag1300 Well that is true right?

[@Sandbag1300]

Thank you. That line gave me the best laugh of the morning. The reason is that everything is safe until it is not.

[@SouthMainAuto]

It is the best advice I can give any one haha

[@keithkennedy4859]

that thing is cool...you have no idea how much you are helping us do it yourselfers in our small home garages with these videos. keep it up

[@kayjob4412]

what is the use of or fun repairing paarts made of recyycled old parts? waste of time...it russty and haalf power!!!

[@nate123123we]

Eric O, You have just made me put my hands in my head in shame - not for the inductive heating but the amount of time I have spent trying to find fully threaded bolts for jobs... Ive tapped many a bar, but never a shanked bolt for some reason.. seams so obvious now but never thought of it. I will most definitely be ordering something from the store/stickers as a thank you!

[@RockandrollNegro]

I think this is backwards. Guys at home would use a $20 Harbor Freight torch. Guys in shops would use a $440 induction heater.

[@justinjagielski739]

LOL! Pretty much what I was thinking. Still a neat tool though.

[@davidramey7186]

Can’t wait to harbor has a $20 heat induction tool It’s coming I’m sure These can be made a lot cheaper

[@javiercoronel1169]

$440 wtf

[@ssible]

I have a 1200-watt magnetic High Frequency induction heater with a couple dozen coils, free winding elements of different lengths, and flat coils. I also have torches, etc. This heater has some serious advantages over my oxy-acet torches, especially when using near rubber, paint, electrical, and plastics. This machine makes it so much easier to concentrate the heat better than the flames of the torch. Also, prices have fallen significantly over the past 10 years as well as the increase in power.

[@flyingbelowradar1557]

You probably already know this but years ago an old welder friend of mine showed me to squirt a little motor on the bolt when it's red hot, the heat sucks the oil down around the bolt threads and presto, the bolt screws out with ease. Never heard of that heat inductor, I will get me one of those.

[@myrnawhitley2681]

bplovescars nh

[@franksunden8789]

Yeah,I'm the retired machinist your talking about,but the inductor was eye opening,thanks,very enjoyable info !

[@jschirr]

This was very informative, I knew these inductive coils existed but did not know they had been modified for portable shop use. The price is a little high for the home DIY guy. When I have a cramped space where i cant use a torch, I have had success with a heat gun from harbor freight. Thanks for stopping what you were doing to share this information. Joe

[@DennyMK007]

People don't have ~$20 torch kit at home, so let's recommend them $431 Magnetic Induction Heater Kit, also $106 Coil Kit to go along with the heater kit, because $431 is not expensive enough - $537 total is just right! (prices current at the date of this post). P.S.: You don't know how strong you are man :) Ripping bolts all day long :)

[@mcshawnboy]

I searched for DIY Induction Heater and there's a power supply for like $10 & Banggood.com has one for $269.99 with the coils.

[@mcshawnboy]

I am pretty sure if you have any type of welder if you hassle the manufacturer or community threads you can find ways to transfer heat to a solid metal object via conduction which is very much on par with this technology. If it's not an object not difficult to access, especially something small/portable can be able to have its chemical bonds broken by reverse electrolysis & Broax Washing Solution meant for washing clothes.

[@watcherofwatchers]

I don't have a torch, nor do I want the huge cylinders and the PITA of refilling them. You're damn right this is a viable alternative.

[@reeceredfern529]

you just broke the 20,000 subscriber mark. not suprised the videos just get better and better keep up the awsome work

[@SouthMainAuto]

+Reece Redfern Thanks!

[@bluegrallis]

The first I heard of Induction heating, was when I worked CAT gear factory in 1978. I was an inspector in heat treat department for about 6 months, and they used induction to heat treat gears and shafts. The machines they used had centers like a vertical lathe, or a fixture for say a bull gear. The coil went around the part as it turned and the coil advanced up the length of the surface to be hardened, while the quenching liquid sprayed on the part just below the coil. Very fast without heating up a huge furnace. A 5 foot diameter, 600 hp electric motor ran the generator and on Sunday night at the start of 3rd shift, it took all of a half hour for it to get up to speed.

[@danthemanoth]

New to your channel, I've been a shade tree mech almost all my life and I think I learn something knew every time I watch one of your videos, You are the Man!

[@MrSpanky473]

we also use induction heaters to warm things up in the oilfield. It's called a 3 pound shop hammer. Works wonders.

[@stevo2310]

😂😂😂👍🤭

[@kadams6868]

This is the answer for homeowners without a lift. Where we are on a creeper with the frame six inches from our face. A torch is really out of the question.

[@Blogengezer]

Started as young NCR tech, back when complicated, heavy geared, National Cash Register mechanicals were still built in Dayton Ohio. We used a carbon contact electrode device. Looked like large needle nose pliers with jumper cables, powered by a large 12-18 VAC transformer. The resistance between the carbons, then turned whatever was squeezed between the carbons, red, in minute or less. Thanks for great vids and technical diagnostic so rare today resulting in the "Parts cannon".. precious.. lol :>)

[@darrelfuhrman8217]

Years ago at an electrical shop in town that would rewind motors, I saw a rewinder take a huge Weller soldering gun, remove the tip, put on a homemade coil of stove or range high temperature solid wire, make a coil, install it on the Weller. He heated a 1/4” bolt & nut. It took about 5 minutes. I was always going to get one of the huge Weller guns to do it with. Now Bill is gone. This was late 70’s. About 77 or 78. Hello from north east Montana.

[@hawaiianf1504]

How To Heat Up A Nut or Bolt WITH OUT A Torch -- Just get married.

[@BPantherPink]

Came from Bigclive giving you a shout out !! Subbed too.

[@BG-gg9pl]

I’m glad he’s doing some advertising. Many times I have wished for one of these working on classic cars, in areas where don’t want flame, or when you need serious heat control. Cool, cool.

[@rickn5006]

Been a machinist for 25yrs. Grew up wrenching. I can appreciate the cordless impact threading method. Remember to forward some and reverse to break the chip. Nice job!

[@umajunkcollector]

very impressive, thanks! SOLD

[@claytoncoolidge992]

Another good way is those cheap midsized butane torches. I've gotten quite a few seized lugnuts off on the side of the road and it also works as a wire stripper a soldering torch also will braze small copper pipes and the help heat up lunch if needed

[@chrisnielsen3562]

Yep I use the small torches you buy at harbour freight or Princess Auto torch head is smaller than a regular torch so I can get into tighter areas and concentrate the heat where it’s needed. Just stay away from fuel and brake lines 😁

[@martinwalters1954]

Hey..I have to say..I watch as many youtube indestructibles as I need and can. But YOU.. are the most humble, helpful, insightful man I've come across yet in 10 years of searching the mechanic oriented videos. I'd send you a six pack of beer..or sompthin like that if only I knew where to send it. Oh well.. KUDO's to ya! Oh..btw.. I understand the physical shit too.. I'm 72. Thanks again!

[@greenbudkelly2820]

Super handy rig. I just bought one in early 2023 for $200. Great for brake bleeders among other things. Not just for steel, it works on aluminum, copper, brass, bronze. I use mine for annealing my brass cases for reloading. The tighter the coil, the faster it works.

[@tootall5559]

old vid, but I didn't know such a thing existed. I'll wager they're not cheap. I have seen many a time when this thing would have been just the right tool. Three are many places on a car you do not want to use an open flame, while the heat on the bolt is okay, flames tend to go places you don't intend.

[@MrWayneploof]

I find after getting it hot i cool it with water to break the rust works great every time. an old guy showed me that many years ago

[@omcara1]

Musta been the same old guy... That taught me that too. lol

[@gary00832]

Are you tempering of tryi g to get it apart lol jk

[@yourlocalalexis4578]

finally got me one after i took out a bolt near the gas tank with the torch, ...the heater is amazing!!!

[@kadams6868]

Thank you for all of us that have spent hours trying to remove rusted bolts, nuts etc. they make a smaller unit now. Pretty pricey. But hopefully worth it.

[@SkubyRu]

New sub here.. Love your channel..! Very personable and informative .. Keep up the great work!

[@smfaisalabas]

Sure. For us, at home newbies, who don't have torches, it makes perfect sense to take out our induction heater :D.

[@sqautch2901]

I was a tech for 10 years and the rusty bolt squeaking was music to my ears. Now the with listing to it not so much. Lol I love your videos keep them coming.

[@DaTwistedOne1]

I used to do induction brazing on International Harvester fuel lines. No matter how many lines I did I was always still amazed watching it heat, flow, and cool down.

[@nomuff2tuff87]

Those saying they will stick to torches have never been in a position as a mechanic whether it’s cars or heavy machinery and you NEED this tool. It’s a prized possession lol.

[@willsrestorations]

This is all right if you have the bolt and nut it's already been removed from the car. But if in most cases you have to get at something that's buried somewhere or even an exhaust bolt it would be considered useless

[@tobygathergood4990]

I have one of these, and it gotta be one of the best and most used tools in my home shop!

[@Elaba_]

Your talent is teaching people. Keep on providing content.

[@thewrenchmaster122]

Inductive Heater 😂 I think people at home might have a torch before one of those

[@johnghatti5435]

This is a year old comment but an inductive heater is 1/3 maybe 1/4 the cost of a torch so they may just have the heater.

[@wssides]

@@johnghatti5435 Yes, and with care can be used beside a leaking gas tank.

[@brentclark8344]

@@johnghatti5435 k oh

[@ciphergalm1174]

simple heat gun is like 50 bucks 1200°

[@SooSmokie]

Then try not to think too.much

[@farmerfb]

I use a full set of torches, but I also have a set of super small portable bottles of oxy acetylene. When you can't use that high heat open flame though, these induction heaters are the boss. I used one around the gas tank of a Caliber where an open flame of that magnitude was just too much, so much savings in scare factor by using induction.

[@alconk7129]

Thank you really enjoyed watching your video! Really like your down to earth personality as well.

[@jw4620]

I scrambled breakfast on an induction hot plate this morning. Working like a charm for many years.

[@davidfrank2824]

I know it's been some time since you put this video up. There has been some other KZbin videos that have come out since then with the Chinese knock off of this tool. One KZbinr as he was videoing what he was doing plugged everything up went up to the exhaust bolt underneath the car turn the tool on and 5 seconds later a puff of smoke came out from the body of the tool. I had made one of these from eBay parts a few years ago. The only bad thing is that practically have no use for it since it's impossible for me to get it under the hood of the car to use it on one of the bolts. It's basically a bench top tool. It's still comes in handy on certain things. When I'm working on mine or someone else's gun and trying not to break screws I can put the part into the coil heat up and then remove. A lot of people really don't believe how he can make a difference. I have a good friend of mine who's quite a bit younger than myself and when we were working on the steering of my expedition we could not remove the pitman arm bolt and I told him just let me get the torch and heat it up. He insists that that would not work that he has dealt with stuff like this and just needed to spray some lube on it. 2 days later the bolt was still in place and this time I wasn't asking I went and pulled my torch out and in less than 2 minutes it came out with no problem at all. Now that he's a believer whenever he's working on something around the house he's using the torch all the time lol. Like always I enjoy watching your videos and I always make sure even if it's an old or new one to hit the like button and of course the first time I hit the subscribe button also. I figured that's the least I can do with someone sharing knowledge.

[@ronbean7243]

Very informative, yes I have always wanted one of these, you must have same salt/rust we have hear in Blighty, one of our early exports

[@HiPPOWUB]

Thanks to you and Rainman Ray i have learnt lots of usefull things. Was really nice to find out how especially the tap set is used, always thought the tool set looks complicated (not really have han an use for it either) ! Too bad an induction heater is too expensive, its a neat tool.

[@limuemu4364]

And here I thought you were going to use a battery and jumper cables.

[@jolllyroger1]

I'm a machinest and I liked your way of threading fast and got er done.... Could go into all the bull about thread cutting pitch angles depths etc etc but no one can argue if it works.... I often turn nuts into dies for threading just by cutting grooves into the nut with Dremel cut off wheels.... And I have screw cutting lathe and cnc mills.... Often make my own taps in the lathe.... Just a question of how much time.... Often is faster to just make something than make a run to the store for a tool..... Besides there was a time when every thread was as different as fingerprints way back.....

[@rider9195]

Just checked the SMA store and the Mini-Ductor 2 shows "Too low to display". AKA, $499. Gave me a chuckle after a long day, lol!

[@dougkubash8673]

I've been threatening to buy one of those. Thanks for the demo! I seen 'South Bend Clutch' on your tool box, I give them business. They do a good job!

[@quakelegion]

Heyyyy guys, just a heads up, if the sleeves on your induction coils come apart, just get some universal Fiberglass Wire Sleeve/Insulating off fleabay and re-wrap the cables!

[@inodoge1897]

This is what im looking for, an expensive alternative 😂😂😂

[@BrianHoff04]

Yea.. I'm the machine shop guy that curled up a little. But, you got it & it'll work. That's the name of the game. Thanks for the video.

[@baxrok2.]

Thanks for thinking about us little guys Eric! Familiar with inductive but never seen it used on a car for that purpose. Thanks!

[@shane250]

These go for $250!!! I can buy a small butane torch for 1\10th of that! The inductive one is much safer, since you don't have to worry about torching surrounding rubber, fuel tanks\lines, or yourself. But for someone with only 1-2 cars that does his own work, I can't justify the investment.

[@mikef8769]

Congratulations on 20,000 Subs!!! Well deserved, best automotive channel on KZbin!!

[@SouthMainAuto]

+Mike F Thanks!

[@heyitschinoable]

Definitely is

[@kayjob4412]

what is the use of or fun repairing paarts made of recyycled old parts? waste of time...it russty and haalf power!!!

[@paulchinn5981]

I have been around automotive all my life and never seen or heard of one of these. They look and work amazing. Thanks for sharing this. I will be having one soon..lol

[@JoseVazquez-rw1uq]

From beginning to end, this episode is so mesmerizing.

[@jeffreybaca302]

Sometimes you can't use a torch. That's the point of the video. Yeah, it's a little expensive. Probably not as bad as a car fire. Just another option.. Thanks Eric.

[@dolnick7]

Great. I don't have a $20 bottle of propane laying around so I'll just whip out my $900 gizmo from NASA. Why didn't I think of this before?

[@SouthMainAuto]

In what part of the video did I say it was a cheap alternative?

[@dolnick7]

@@SouthMainAuto Just yankin' your chain. Enjoy your videos very much.

[@cameracamera1319]

Lol. U naughty troll. Lol

[@emtscythe3782]

Congrats on 20k Eric. You deserve it and all to come. Your right some machinist just dropped dead of a heart attack. Lol. Oh well can't count how many times I've done the same thing. Looked like a grade 5, zip, zip, done!!!

[@kevinwood3883]

As a retired 40+ year mechanic it's nice to watch another "old school" tech. No throwing parts at it... ya fix it.

[@Thommie63]

Eric- next time you use the bench grinder with the wire wheel; PLEASE use eye protection !!! In all the steel work I've done; I've seen those pieces of wire fly all over the place.. we only got 1 pair of eyes... thom ...

[@ChiralSpirals]

Im in love with your workbench.

[@gunggunglu2424]

看过你的多个视频，你的修理技术是很好的!👍

[@ccdude608]

Hey dude thanks for info, you should send a anonymous thank you card/letter to DOT for all that salt on the road. HA

[@SouthMainAuto]

I buy them donuts when I can haha

[@tasmaniandevil7610]

Cool tool Will it remove exhaust bolts ?

[@AlwayshighAlwayshigh]

dude your super awesome plz continue to bless the world with your vids

[@kevinwoodcock7578]

What a freaking awesome tool box....Man I love tools

[@jeffreydeutsch7336]

Do you love it $500 worth? He never mentioned that.

[@robertfreeman5231]

If someone does'nt have a torch , they'll have one of these for sure.

[@bretteitniear3718]

Good god man, the negative comments on here makes my head spin. Haters everywhere it seems... I never thought I’d own a $4,000 Norco power train lift for my personal garage but low and behold I scored one for $500. I think the point of the video is to enlighten people to its existence and function. Maybe you’ll come across one at a surplus sale for pennies and being open minded and aware, boom! You just scored yourself a tool you never thought you’d be able to own...

[@edwardmulder3777]

Another great super expensive machine is the laser rust remover. Can't wait for that to become cheap

[@KevinJohnson-fx6wq]

Damn, I wanted to see the blue flame. I'm as disappointed as the day they cancelled flame thrower day on me in the army. Really nice tool. One thing you said about using the inductor on cold vs hot metal. The cold will actually heat up faster than the warmer metal. We actually proved it in physics class. What happens is the cold heats up in a straight line where the warmer metal actually has to cool a bit first to match the heat from the inductor, not a big time lapse but it happens. I always try using the coldest water I can to make coffee. Works the same. One guy I met, put hot water in an urn thinking it would work faster, nope, it wasn't working at all. Thanks for sharing, Saw your Happy Holiday vide and forgot to say ' Happy Holidays ' and thanks for sharing.

[@akm03051]

We had one at the last dealer I worked at. I loved this tool , it especially worked great for seat belt anchor bolts and fuel tank strap captured nuts.

[@davidgillettuk9638]

No doubt these heaters are brilliant but in the UK they cost between 450 and 850 quid..😫 A lot of money if like me you are a diy and hobby mechanic. I will buy one when I retire and do some serious car restoration though. Thanks for the vid.

[@testosteroneinc.3800]

This would be perfect for gas tank strap bolts. Using a torch is suicide.

[@obsoleteprofessor2034]

Living the vida loca.

[@wr3ncher]

Inductive heaters are awesome. Worth every penny! When you have a bolt thru a rubber isolated bushing, IE spring pin bushing, control arm bolts getting stuck in the metal collar, anywhere you don't want to use a flame. Or if you're just bored and easily entertained you can turn it on and put a chunk of aluminum inside the coil and watch a cool magic trick. Fun for the whole family. 👍

[@cvpi06]

Never knew they made a hand held version. This is good to know, thanks!

[@subparwelder]

Thought he was going to say, "There's a machinist out there turning over in his lathe..."

[@donpoelman6627]

Nice Coffee mug w/ the Canadian flag!!

[@davidrobins4025]

Creative ideas. Thank for showing us how.

[@KLX1990]

i don't always watch car repair videos but when i do, they're south main auto

[@cristobaltorres3625]

Hadn't seen such tool before

[@oldguywisdom2904]

If you don't have a heater or a torch just use a magnifying glass and bright sunshine 😂

[@scottcarr3264]

Very good clip, a very handy item especially when the situation may be dangerous to use Oxy acet torch.

[@grc5618]

Making threaded parts is so satisfying...never gets old

[@camberwellcarrot420]

That could have saved a lot of butter knives from being stuck between stovetop coils in the 70s.