How to install a 100cc/80cc engine on a bicycle

Hello! In this video I will be going over EVERYTHING to install a 100cc engine on a bicycle, this would all be the same for an 80cc engine as well! I hope you find this video helpful and can learn a few tricks to make your install easier along the way!
-My 100cc engine
-www.amazon.com...
-1 gallon gas tank with welded brackets
-www.amazon.com...
-28 tooth sprocket with standard 9, and disk break 6 holes for mounting to rim
-www.amazon.com...
-Hub clamp adapter with 36 tooth sprocket~ “not the exact one I bought, and does NOT appear to have hub spacers included with product”
-www.amazon.com...
- Chain breaker
www.walmart.co...

[@Aphoticness]

Sick bikes bro! I like how thorough you are with the vid! 🙂💯

[@Bob-T-Builder]

More to come soon! Plenty of projects, just trying to find the time for each one😂 Appreciate the support!💯💯💯

[@Littleevil9975]

I agree great video

[@DonAlejandro68]

Thanks for being thorough with every step of the build. I was having trouble with my kill switch connection and your video made it so easy and clear. I had my bike running and working in five minutes. Thanks Again

[@Bob-T-Builder]

@@DonAlejandro68 Glad I could help!😁😁

[@007tallguy]

Great and thorough video! I don't know if it's easier installing the clutch cable before or after the chain, but apparently both ways work. I probably would have taken one more link out of the chain, but again, you had it set up pretty good and working just fine!! 👍👍😁

[@Bob-T-Builder]

I actually did take one more chain section out after riding for a bit, it was just a bit too sketchy😬 but I’m working on my update video on the build!! But still keep an eye out for the chopper build cause it will be interesting💯💯💯💯

[@Littleevil9975]

Nice builds bro I just finished a new one recently also thanks for sharing it

[@Bob-T-Builder]

Of course!! Part 2 of the chopper build soon to come! I already got the recordings of getting the engine running, I just have to edit it shorter!

[@davidroman6439]

Thank you for the video Very detailed

[@Bob-T-Builder]

Of course! I’m glad you like it!😁😁

[@GONE4GOOD79]

With your clutch cable you can shorten it by removing the inner cable and snipping the outer cable to the desired length then reinserting the inner cable this gives you a way smoother and easier clutch thanks great video...

[@Bob-T-Builder]

That is an awesome tip/hack! I never thought about doing that! I might just try it to clear up a bit of the mess going on up front! Much appreciated!💯💯

[@GONE4GOOD79]

@@Bob-T-Builder No problem ...

[@gamerdad8531]

Cool sting ray how did you manage to install those forks on the bike I've been wanting to mount some motorcycle forks on my Ruff-cycles tango and convert the hole bike into a small motorcycle 🏍️

[@Bob-T-Builder]

Thank you so much!😁😁 And awesome question! I stole the whole front end off of a 1974 Honda dirt bike that my dad and I could never figure out the wiring harness to, I used the original bearings from the chopper frame itself as well as the ones off the Honda shocks and still had to fill in some space with some extra bearings I had from old BMX head sets, (I suppose using washers in between would work as well). I will be dropping a Q and A style video soon on topics I wanted to retouch on the 100cc engine build and I will address the the chopper forks in more detail at the very beginning! I also forgot I needed to swap out one of the bearings and re-grease everything so thank you for your comment to remind me!!!😇😇😇

[@gamerdad8531]

Thank you for your your reply and I look forward to it

[@Bob-T-Builder]

@@gamerdad8531 I also forgot to mention in my previous comment that I also have a long threaded bolt down the center of the head set assembly, with very large washers, to clamp everything together as an extra safety precaution so the forks don’t fall off while I’m riding! It isn’t necessary at all but I’d rather have the extra redundancy and be safe than sorry😅. Again I will try to show EVERYTHING about it in the beginning of my Q&A video for you!💯💯💯

[@luukuh955]

What if I grind/trim the muffler ?

[@dwubprod6683]

If my clutch isn’t disengaging should I tighten the cable more?

[@Bob-T-Builder]

Yes that would be the most common issue, and if there is not enough adjustment on the clutch handle part you will need to bottom it back out and re-tighten the cable on the engine side!

[@Idostuffguy]

Bro your cable management is a mess😂😂😂

[@Bob-T-Builder]

There’s not much you can do when you have like 2 extra feet of cable😂 maybe I’ll look into a Bluetooth throttle and clutch🤣🤣

[@JMJGaming11]

This is giving male Karen vibes …