Great video. I used this rope method on my Jeep J20 and it worked a treat. Just a point on the J20 or Wagoner because of eyebrow on the top of the cab when you place the bottom of windshield into place the top of the glass and gasket will rest on the eyebrow. However as the gasket is seated from the bottom and sides the top of windshield come below the eyebrow and seat in he correct place.
@RuderalisFPV2 жыл бұрын
Why did you leave out the glazing bedding compound?
@bettesmith11178 ай бұрын
Great video, thanks!
@kermitefrog643 жыл бұрын
Nice video. I need to look at one of the videos for the back window but it probably is similar. Dennis Carpenter has great products for my 1964 Ford F250.
@kermitefrog643 жыл бұрын
One of my next projects is preparing the bed to get a coating since it has accumulated some rust.
@hotrodray68022 жыл бұрын
What about the auto bedding and glazing compound? Is there no sealer in the rubber channel? Ive had them leak with no sealer.
@genmaxpain7 ай бұрын
you are meant to use sealer after you finish installing by heating a non hardening sealer in the sink for 30 minutes prior and peeling the outside lip back and adding sealer then you push the lip back down and clean the sealer that squishes out, job done, bit of a shame they dont mention or show this
@aston0708 Жыл бұрын
Great video,,,,
@leealice61212 жыл бұрын
Great video!!
@ninja636393 жыл бұрын
Now do one on the shoebox windshield...please 😁
@wilfredohosana99772 жыл бұрын
I love it.
@lifegoeson40854 ай бұрын
Could jus push out the WS 💪🏼
@creeew3 жыл бұрын
Helpful
@peggsworld59643 жыл бұрын
Did you use the Glass Bedding Compound ?
@amritavikram12 жыл бұрын
Awesome
@frogman78744 жыл бұрын
REALMMMMM!!!!! 👍
@michaelwurn6268Ай бұрын
Do you have a video of this on a 1940 Ford Car or some other split windshield setup?
@ac50154 жыл бұрын
Can this be done if your assistant is slightly grumpy?
@JasonTYoung234 жыл бұрын
yes but it may take twice as long
@ac50154 жыл бұрын
Jason Young that’s good to know
@cheapcargarage Жыл бұрын
You left out the step for the glazing compound?
@troychampion7 ай бұрын
thx, sub'd
@AnthonyMartinez-ke8jy3 жыл бұрын
Can you put a video how to install the windshield on a roadster pickup 1929
@THIRSTYGUMS4 жыл бұрын
What about the bedding glazing compound??
@denniscarpenter4 жыл бұрын
The bedding glazing compound is optional and can be used between the gasket and the pinch weld. Some customers apply it to the gasket before installation. We prefer to pull l up the gasket lip and apply with the caulking gun.Thank you for your comments.
@EcoGreensFarm3 жыл бұрын
Better method is to lay a bead of urethane (3M 540, or Sikaflex 221) around the pinch weld, and let it set up for 15-20 minutes, then install the window as shown. The window will never leak this way. If you don't use sealant, your window will leak, and you will get a rusted pinch weld.
@barbecuebob18368 ай бұрын
I am pretty sure urethane is a big no no on these. The windows bedding compound allows the window to flex and it needs to. If you use urethane you risk cracking the glass. This is why rope caulk or butyl is used. @@EcoGreensFarm
@adamwnichols Жыл бұрын
What is the difference between the premium seal and the economy seal? Looking at buying one for my 69 f100.
@bradboustead16824 жыл бұрын
Can you describe where the bedding and glazing compound was used? My windshield is installed and getting some water in around the glass in the lower corners.
@denniscarpenter4 жыл бұрын
the glazing compound can be used under the gasket where it meets the pinch weld of the opening . If you are getting Leaks pull back on the gasket and apply a bead underneath and work it into any voids the gasket cannot seal.
@chucksgarage71653 жыл бұрын
@@denniscarpenter Would love to see a video of the bedding compound installed after the glass is installed as you describe in your reply.
@hotrodray68022 жыл бұрын
So wait until it leaks before sealing. Riiiiiight.
@bradboustead16822 жыл бұрын
@@hotrodray6802 My question was from a year ago when I had gasket on glass only, no glazing compound. I have since put in the glazing compound and fixed the leaks. It is a slow cure caulking of sorts. I pulled the edge of the gasket back slightly with a plastic tool and squirted some compound in as I advanced around the perimeter of the glass.
@tomasitodeleon95163 жыл бұрын
I did my windshield yesterday and Today is raining is that ok??
@hotrodray68022 жыл бұрын
they 9nly leak when touched by water
@cdcorrigan10 ай бұрын
Do you recommend sealant before installing the glass or is that done after?
@lynnepotts1943 жыл бұрын
I notice that you don't use any sealer adhesive. What is this??
@juanbarturen27263 жыл бұрын
Hi. I'm getting ready to install my new windshield from LMC. On my O'l Beater 54 Chevy.. I'm trembling. Is it like you did on your Ford ? HELP !
@bigjet064 жыл бұрын
Great video!! What groove is for the glass etc.. Thanx
@TimCBuilders3 жыл бұрын
Pardon?
@yuribreslav-md3er11 ай бұрын
Hi can I buy the tools for windshield repair from you?
@ollylawrence24533 жыл бұрын
If your gasket is fine but you need to remove to treat rust is it possible to pop it out leaving the gasket intact and reuse it?
@hotrodray68022 жыл бұрын
no must cut the lip off to remove glass
@jacobcammer62824 жыл бұрын
No compound needed it's just held on by the rubber
@hotrodray68022 жыл бұрын
no sealer = will leak
@pauldormont44703 жыл бұрын
How is the rubber filler strip installed in the gasket on a Willys M38A1? Do you use a grooved wooden roller like on storm window seals?
@duck869683 жыл бұрын
Looks like a lace in window
@donpedroelbuey81514 жыл бұрын
Are "aftermarket" window seals risky as opposed to OEM, even if installed correctly? I`m thinking of "de-chroming" the seals on my '85 Landcruiser because the chrome trim is virtually impossible to find. There are aftermarket seals without the trim channel, made just for this purpose. Thanks!
@nelsonthekinger Жыл бұрын
Tough!!
@jojodiver87064 жыл бұрын
If you're really anal like I am, you can completely clean the edges with CLR and #0000 steel wool.
@jballs11183 жыл бұрын
Good video sir question I have a 1965 mercury comet 2 door hardtop am having a hard time locating the front windshield any suggestions where can I order it from ?