How to Install DiamondBack SE Tonneau Cover

[@HelpfulDad]

This should be the 'official' install video of the manufacturer. It's got all the little details you need to make the install a success - thanks!

[@Shottacle]

Best installation video of this product on KZbin as of June 2023 well done very detailed

[@ChrisJones-yt8zp]

Nice video. My only criticism is that at 6:09 you showed the alignment of the seal along the bulkhead and it looked fine to me. You made an adjustment and didn't show what it should actually look like so I have no idea what it should look like.

[@mikemead2315]

Good install video. What I would have liked to have seen: - Better close up pictures of alignment with bed corners, sides, hatch seals, and front bulkhead (front bulkhead pic was visually confusing, maybe if from different angles or moving). - Torque settings on bolts. - How squished should seals look. - Is there a tailgate seal that needs to be installed or adjusted. - Operation. i.e. Safety catch in front. - General suggestion about attaching accessories. - Accessories available. - Quick differences between SE and HD and their installation differences. - Assist shock sizes to adjust for accessory weights. The construction and installation seems first rate, cleverly simple, and well thought out ..... except the locking rods. Adjustment of these rods to make the gasket fit tighter or looser should be A LOT easier with just a turn of a bolt one way or another to adjust tightness. Would rather see latches on all four corners so I could get a better seal by pushing down on one corner at a time.

[@jameskelly4494]

Nice detailed video. Best view of installing the C clamps on the center piece that I have seen. I think others have mentioned that it would have been nice to see more detail on the alignment especially the car area where the weather stripping was installed along with the back corners near the tailgate. Pretty much settled on this cover for my 22 Tundra because of the accessories, ease of installation and removal. Just need some warmer weather in Connecticut for the install.

[@SoftHeartHuman]

Also going for it man did you get it how was it!

[@haroldbrown3452]

@4:09 are you actually securing that to a plastic LED light? that doesnt seem secure

[@doctorxring]

I thought so the first time I watched it. But I replayed that sequence and he slips the clamp beside the LED light.

[@Jack_Rabbit_Ranch]

I like how when hand tightening, your fingers make the same sound as a rachet. Very helpful video, thank you.

[@Realtruck]

Glad you enjoyed it!

[@sas1969xj]

should of have shown how it operates when all done

[@ecarlo03]

Great installation video! Thanks!

[@jasonm519]

Great video, very informative and straight to the point. Thank you!!

[@gamebird7379]

Do you have instructions on putting new seals in place?

[@lyleswan6671]

Nice video, really like the extra details!!

[@wt9653]

What is the weight rating for the SE model? HD is 1,600 pounds.

[@VanquishAudio]

400lb

[@amandamcgruder5074]

Why yall don't sell these covers from diamondback??

[@VanquishAudio]

What I don’t get is if your friend is putting pressure on top while you calibrate the lock, don’t you have to apply pressure to both sides every time you have to lock it again? What am I missing

[@doctorxring]

Outstanding installation video. 5 Stars !! Many thanks !

[@gregorys6838]

Question. Is the weather stripping being laid without tugging on the seal? Or is it laid in without any stretching? I'm assuming it's the latter, but the video made me think he was pulling on the weather seal.

[@Realtruck]

You are correct, laid without any stretching

[@akamanonthemoon]

@@Realtruck I'm concerned about weather stripping sealing on my cab side of truck bed as they put the Rhino/Line-X covering on that area as well? I'm not sure if I could remove the Rhino/Line-X covering?

[@dyates6380]

Great video. Thanks.

[@Realtruck]

Glad you liked it!

[@prokofievchambers8603]

Yes, should have given a full functionality session including rain resistance. Incomplete, but otherwise a nice presentation.

[@qasimalzaidy1781]

Great job

[@newtonbruton5252]

really good

[@Daniel2271961]

What’s the total weight of the cover?

[@VanquishAudio]

80lb

[@haroldbrown3452]

best install video on ytube

[@jtplumbing6592]

Wish they made something that worked with an existing tool box

[@Realtruck]

Hey there! You can find all the covers that support toolboxes here, realtruck.com/c/exterior-accessories/tonneau-covers/tool-box/. Hope that helps! 😁

[@haus05]

funny thing is this ford owner is actually standing up in the box

[@wt9653]

Poor man's Plywood version will look great. Save 2000 dollars 😊😂

[@travelinben1966]

Nice cover, but easy on easy off it’s not.