Nobody has explained the attention to details technical side as good as this video does. Wonderful!
@valhallanator Жыл бұрын
Great instructions! Only suggestion would be to test before performing the final installation on the vehicle. You don’t want to finish up the install only to find some kind of problem. Great job, D2F! I’m armed with the knowledge I need to try this myself!
@KuromiandmyMelody155 Жыл бұрын
He shows you how in another video
@vg0009012 күн бұрын
Awesome explanation.. have been searching for this since long .. thanks a ton ☺️
@radulescu213 жыл бұрын
This is what I was looking for. I had the DRLs directly on the more fancy module, which shorted the right side due to water in the drl plug. Now I don't want to wait another 1+ month from china, and in my country I could only get a "smart" module that has one output (don't know why you would make it like that). And I could not decide how to split one module output in 2 DRLs. But seeing this I remembered I still have the driver that came with the DRLs. So I'll connect the single output from the "smart" module to that one, which will split to both DRLs. Awesome, thank you
@larryhicks75582 жыл бұрын
T tap are very bad many problems with intermittent shorts. The soldering may take longer to do but when heat shrink does not cause problems. I will give it a go . Looks like easy instructions Thanks
@CertifiedShadetree4 жыл бұрын
Thank you for posting those links!!
@omprakashmagaji24164 жыл бұрын
DRL gives your eyesight glazed 😎
@MikeKeighley-td8wd Жыл бұрын
Excellent tutorial, thank you from Scotland!
@colinbyers26597 ай бұрын
Great video! It was very helpful! I would like to attempt to add an extra drl to my existing drl on my Nissan but so far I have had no luck. I think I'll try your wiring as a work around :)
@doitbyyourself664 жыл бұрын
Wowww, impressive. Man; I wish I could have ur knowledge about wiring, I drive the same vehicle u do.
@jasonthomas18423 жыл бұрын
very clean like always. Nice work!!
@71mrbigron2 жыл бұрын
Thank you for the informative video, great work.
@robertmunroe39763 жыл бұрын
Great work, thanks! One question, are you satisfied with the daytime brightness of the new DRLs(ie - do you think that drivers/pedestrians can see them at a reasonable distance)? On video, it’s sometimes hard to really know how bright they actually are. Thank you, your explanations of the controller answered a bunch of my questions. Cheers from Washington state!
@dial2fast3 жыл бұрын
Yes these DRL lights are bright and visible during daytime. You can see them illuminated from a distance.
@hockeynate2 жыл бұрын
I read somewhere that you could make them shut off when the headlights are on.
@markvosper24938 ай бұрын
Easy, just connect the return wire (the negative) on to the supply (+) of the park lights.
@MrMarineMaster4 жыл бұрын
You are amazing!! Great video! All links, etc 👌
@dial2fast4 жыл бұрын
Thank you! 😃
@jorgevega2384 жыл бұрын
Ive been waiting for this
@Kucingkelabu13373 жыл бұрын
soo neat and cleann.. I wish you can help install for my car haha..
@njtg88133 жыл бұрын
Nice clean install...
@swkynard3 ай бұрын
Great YT video explaining how the DRL controller works. I have a question, I am an electrician and use a multimeter daily, what is the device you have clamped on the ACC wires to measure relay voltage called? and where can I find one like you are using? must penentrate the wires with the alligator clips in order to get the wire inside the insulation.
@dial2fast3 ай бұрын
It's a FLUKE AC89 amzn.to/4afcIlz
@speedfreak11614 жыл бұрын
Thanks bloke 👍🇦🇺
@malikawanawan17144 жыл бұрын
Nice video thank you sir
@dial2fast4 жыл бұрын
Thanks for your comment!
@muhdazman2528 Жыл бұрын
Great. Very helpful.
@immanueldelcastillo60413 жыл бұрын
Hello, do you have an in depth instructional video regarding tapping on relays? Thanks.
@dial2fast3 жыл бұрын
Here is a video on how to tap wires kzbin.info/www/bejne/qJvYaICaYpx6itE
@williamkmounts63682 жыл бұрын
My question would be if you bought aftermarket drl headlights that the drl is controlled by the marker light. Can you easily make it to where the drl is turned on with ignition?
@henuemphuse9 ай бұрын
That's what the drl controller does. And why you would need to tie the signal wire into acc or ignition power. For what im doing id rather just use the spare empty relay and fuse slots in my fuse box and do all my wiring in the fusebox. A lot cleaner and if the fuse or relay goes out I can just replace it with one I can get at any auto parts store.
@batvon393 жыл бұрын
Awesome. Very detailed and well explained. Will this work with any LED lights? Or is there a special type that can dim?
@dial2fast3 жыл бұрын
It will work with any LED DRL light, but not LED headlight or fog light.
@batvon393 жыл бұрын
@@dial2fast thanks!
@batvon393 жыл бұрын
@@dial2fast I just installed the module but I can't get the lights to dim. Just a small flicker but not that 30-50% drop. If there's too much power from the lights will that prevent dimming? The fuse the module came with blew once I hooked up both lights, so I had to get a bigger one. Really appreciate the help!
@dial2fast3 жыл бұрын
@@batvon39 Sorry for the late reply. I am assuming you bought the iJDM DRL control module for the install. If you did, the white wire need to be connected to either parking light or headlight +12V wire. When this wire senses 12V (you turn on the headlight), then the DRL will dim. If your DRL is having problem turn on and staying on with ignition, then you may also need to connect the blue ACC wire from the controller to ignition 12V. If you have done all this and still having problem, you should contact the seller for further assistance.
@batvon393 жыл бұрын
@@dial2fast No problem at all, thank you for all the help!!
@ivanporcalla3 жыл бұрын
Very helpful!
@mountainhopper95733 жыл бұрын
Nice Job!!
@angelcabrejos83142 жыл бұрын
Pls where did you bought the products, in Amazon are different.
@zmohp.20603 жыл бұрын
Good day. Can I just directly tap the drl control module red (positive) wire into the factory drl light positive wire to power it? I'm just not comfortable to tap the wire from the fuse box.
@warnin41972 жыл бұрын
Looking for this exact same answer
@organicvids2 жыл бұрын
There is a positive wire to power drl then there are either one or two trigger wires to 12v pos. The trigger wires allow module to sense 12v to dim drl OR turn them off depending on module. Hence if for instance on this model the trigger wires are turning triggering off and on response to 12v from signal being intermittent due to turn signal relay. If you trigger wire is tied to constant 12v source they will stay on all the time so no you cant tie the 12v battery supply wire to module to trigger wire or they wont turn off HOWEVER if you tie 12v trigger wire to an accesory like cigarette lighter fuse they should turn off IF you cig lighter circuit turns off when you shut off ignition. There are circuit add ons to allow you to plug a blade into positive side of fuse circuit to add a line. Auto parts store has them.
@trelaw1235 Жыл бұрын
Thanks for the great video. I installed the exact controller yesterday but when I turn on my turn signals my LED flashes with my turn signal. It’s suppose to turn off the LED to my knowledge. Any idea why that is? I have yellow to positive turn signal.
@stevelayPapa4 ай бұрын
I need a system that will Turn DRL "only" when the lights are Turned to "Parking Lights". Can the yellow blue wire be used for that feature? Other wise I want the lights to turn on when engine starts, off when shut off -after X seconds and dim when Headlights turned on.
@paulsosa18722 жыл бұрын
Could you wire the LEDs directly to a accessory fuse using a fuse tap? Or is the DRL driver that comes with the kit necessary?
@dial2fast2 жыл бұрын
You can wire it directly to ignition 12V, but usually you want to the DRL to dim at night because it's too bright for night time.
@nanonanonano11664 ай бұрын
I bought a similar drl that has that white cable for dimmed off but when I connect them to the power while drl on, it just turned off the drl, i’m wondering if I need the drl controller too?
@kingdave69104 жыл бұрын
Do yu have a video or do one where you add the self opening trunk??
@agustincorrea3244 Жыл бұрын
Great instructions I purchased thru Ebay new LED Lights for my Audi Q7 2009 and at night it turns White and the signal changes to orange. I want to use the White LED to stay on all the time that way I don't have to turn on the night lights during the day. What I need to buy in order to use the front bumper LED's as Daytime running light with no Dim.? Thanks Auggie
@dial2fast Жыл бұрын
If you want it to stay on white when you drive, then just connect to ignition 12V. So when you start your car, it will turn on, and off when it turn car off.
@markowalters-gerout78533 жыл бұрын
Still learning everything.. Will the drl flexible tape work the same why? The car I want to install it into doesn’t have running lights.
@brendonrutherford51186 ай бұрын
I'm gunna throw a spanner in the works of a DRL installation. In New Zealand & under current vehicle by-laws & what we colloquially call a WOF (vehicle, Warrant of Fitness) when you go to turn on your side lights/mains etc your DRL/s must actually switch off automatically & not merely just dim in visual power output!! It is therefore illegal to have both your DRL/s & your main lights (high or low beam) on. You can have one or the other (DRL/s or mains) but not both switched on at the same time. If you are going for a WOF at the time you will be rejected as I was!! No WOF means you cannot use the vehicle on a public highway period!! So I'm looking for a suitable wiring diagram to cover this scenario & any help or assistance would of cause be most appreciated. I'm no auto electrician but I'm not green behind my ears either & have a reasonable understanding of basic vehicle systems. I've actually completed a wiring diagram to cover this requirement but would like to compare it with somebody else!! Any takers please???
@normandfogarty3505 Жыл бұрын
Great video!! Do you know if this setup meets the Canadian requirements? Thanks.👍👍
@alexmarroquin82473 жыл бұрын
Could you please do more videos on the Nissan Pathfinder. Very interested on what’s possible to do with this vehicle
@dial2fast3 жыл бұрын
Yes I do have several things planned on the Pathfinder. These videos will be coming in the next few months. Stay tuned and remember to subscribe. Thanks
@ibolTV Жыл бұрын
I have a question sir . I have an existing fog light switch with relay and top it on ignition. And I want to use this as a drl switch. I trace the connection red wire goes to the firewall and both have a Blk wire that tap on body ground . The problem is , I bought the drl harness with module dimmer . It say on the diagram the red wire with fuse should tap on directed to positive of batt. And Blk wire neg of batt . The blue wire (ACC) where should I tap ?. On the red wire of the fog light switch ? Or should I ignore the blue wire. Or maybe the red wire with the fuse I tap directly on the positive of the fog light switch that goes on the firewall ? Thanks in advance
@pauljohndasalla87442 жыл бұрын
Hi! I have a question. I bought the exact same LED DRL ligh bar and also bought the module. I installed it, but for some reason it wouldnt turn off.
@e4James Жыл бұрын
I have some sequential mirror turn signal DRLs. It came with a normal plug in and play connector but also has a white wire for the running white lights. Someone said I could jump the window switch wire to get the day time white lights to work. However, my car has auto headlight on and off feature depending on the outdoor lighting. I wanted the mirror running lights to run off the same function is there a way to jump the white into the column selector wire for “Auto” so it works the same way as the headlights go on or off based off ambient light?
@jonathan.varghese2 жыл бұрын
Dude thank you so much, this video has been really helpful. I'm still confused about one thing, though. The DRLs I'm looking at have a seperate, amber sequential turn signal. Does that wire get tapped in directly to the OEM turn signal? From what I can tell from the DRL controller, the "turn signal" wire on the diagram (on the Amazon page) has to be a kind of input, that I think makes the regular drls flash along with the OEM turn signal but I'm not sure how to connect the turn signal so it will use the Amber sequential one. Also if you hook up the blue ACC light to ignition 12v do you need to connect the DRL controller to the battery?
@dial2fast2 жыл бұрын
If your DRL have separate sequential amber turn signal, then you can connect the white DRL LED wire to the DRL controller (as shown in video), and you wire the amber sequential turn LED positive wire to your factory turn signal light + wire.
@topandrun126 Жыл бұрын
I just ordered this drl a few days ago I haven't received it as yet. But I was reading a few comments on Amazon saying that this drl do not compatible with US vehicle. Is that true? Thanks.
@asmr-everything6304 жыл бұрын
What kind a led you use for low beam? Are they good brand? Do they give interference in radio when lights are turned on?
@ACaseyPodcast2 жыл бұрын
I have a Ali express Mazda 6 drl set which does constant on and turn signals. The bezels run to a box that lets out a red, black, blue and 2 grey wires. I need someone to tell me where exactly to wire these too. I’m guessing black to negative , greys are prob indicators.. haven’t a clue where to wire red or blue
@luckylonner146 ай бұрын
Hi Sir, thankyou for the video, i have similar drl controller and drl light, can i use fuse tap (piggyback fusetap) and put in on the acc of my fuse box the drl controller?
@dial2fast6 ай бұрын
Yes you can get power from the fuse box with ignition 12V, then it will turn on/off with the ignition.
@luckylonner146 ай бұрын
@@dial2fast thank you much Sir, one last question the drl controller has a fuse to it. Should I put also fuse on the fuse tap like 5a or lower? I dont know how much is the ampere of the fuse on the drl controller. I will input the piggyback fuse tap to an empty slot of my fuse box with 12v on it.
@dial2fast6 ай бұрын
Even if there is a fuse on the DRL controller, you can still use the fuse tap on the fuse box. For regular LED DRL, 5A (or 10A) will work fine. The 'LED DRL' light itself won't draw more than 1A (assuming that's what you are using for lighting). A rule of thumb when it comes to the placement of a fuse is there should always be a fuse closest to the power source (in your case, it's the fuse box, so using a fuse tap is ideal)
@luckylonner146 ай бұрын
@@dial2fast thankyou so much Sir for the knowledge that you share.
@HK3045 ай бұрын
I can't seem to get my drl wired up. Tried to connect to the headlight but it won't work
@mariomanzatti89513 жыл бұрын
A very professional installation...I need to get one of those modules, do you have a link to it please....
@dial2fast3 жыл бұрын
See link in description.
@mariomanzatti89513 жыл бұрын
Hi there, so do I need the drl driver aswell?? I cannot just have the drl controller connect straight to the led’s,,,any info would be appreciated....
@dial2fast3 жыл бұрын
@@mariomanzatti8951 In the video I installed the DRL driver because that's what came with the set of DRL light I purchased. The DRL controller can power DRL light on it's own.
@markvosper24938 ай бұрын
The driver should help to regulate the current so they last longer
@ChikaCheeks2 жыл бұрын
Ok I’m on cycle 12 of this video. Mine doesn’t have a separate power supply. All wires are on the DRL controller. So I have a red & black (tye red with fuse on it)- that red goes to then 12v fuse correct? Then I have the to wires that connect to the LED via snap connect - I’ll connect those. They both have a yellow turn signal- I’ll cut this off. Then I have a white wire- I’ll connect to my parking light positive. Then I have a green wire that flashes so I’ll cut that off. Last, I have a blue wire that control the dimming function. Can I splice that wort the red wire that has a fuse on it, I hope you get me
@dial2fast2 жыл бұрын
If you have a similar DRL controller, and you connect the controller's red wire to battery 12V, then it will turn on the LED DRL when you start your car, and there will be a delay in the shut off. If you don't like this, then you can connect the controller's red wire to ignition 12V. The white wire can be connected to your parking light if you want to use the dim feature to dim your LED DRL when you turn on your headlight.
@firemandkdkdk2 жыл бұрын
or you can hook the white wire up to the low beam power , then they are half bright with low beam, and will come on full brightness with high beam, that's how I have mine wired.
@triwicaksono84212 жыл бұрын
Hi mate, On diagram from factory,red wire to (+) battery and blue wire to ACC. I show on You connect red wire to ACC so you not use blue wire?
@firemandkdkdk2 жыл бұрын
the blue wire goes to keyed ( only hot when turned on) and will make the lights come on with out starting the engine OR if you start the engine and they will not come on , then you have to hook the blue wire to keyed power . For some reason, some vehicles will not trigger the unit when the engine is started ( or say you have a hybrid where the engine stars and stops....... if your engine is going back and forth your lights would turn on and off, the blue wirre to a keyed source fixes that ( or so it seems or should ) . I have not heard anyone else say this about hybrid use but I can't be the only person who thought about this .....lol...I'm just a retired firefighter, you know, put the wet stuff on the red stuff....lol.
@ralf85344 ай бұрын
I have a question, would it matter which side is for the turn signal ? Would I have to tap into either both headlights or just one would be fine ?
@dial2fast4 ай бұрын
If you want to connect the turn signal 12V (so your DRL will flash alternately to the turn signal), then you have to connect the left turn signal for the left DRL, and right turn signal for the right DRL.
@ralf85344 ай бұрын
@@dial2fast how would I wire that ? Since the DRL remote only has 1 set of colored wire
@glitzjeeme45003 жыл бұрын
Would like to have an independent switch so I can control it from inside, good to have them on when in forest or dark in the night as well as DRL. any idea where best to connect it??
@tzershernkhaw4 жыл бұрын
Greetings from Malaysia. Thanks for the great vid man. Subscribed! Can I just ask: For power input im planning to tap the ACC on the stereo of the car, and the white wire to 'illumination' on the stereo as well, instead of to the headlamps. Do you reckon it would work? I'm thinking what we need is a 12V to the white wire when the lights are on, im guessing the illumination does that right? Also the ACC on my stereo has already been tapped to power my Steering control module. Im worried if i tap it again, it would result in voltage drop? Thanks in advance for any advice!
@dial2fast4 жыл бұрын
Hello Malaysia! I visited there many years ago in KL and JB. Miss the food. You can use the stereo illumination wire to trigger dimming of the DRL. You can also use the stereo's ACC wire to power the the DRL light BUT make sure that circuit can support all the accessories that's being powered. The DRL light will consume about 300-500 mA. You are not going to have a voltage drop, but if the circuit can't support all the devices, you will either have a fuse blow or wires heating up and melting (fire). Also keep in mind doing it this way require you to run the wires into the vehicle which I personally find it more work. It's up to you but try to keep the wiring clean and safe.
@tzershernkhaw4 жыл бұрын
@@dial2fast @dial2fast @dial2fast Hahaha welcome again sir after the pandemic flying restriction! Actually the reason why i wanna tap the stereo is because I could tap onto the added ISO socket, so that the original wiring remains unaltered. But yea I might drop this idea considering the fuse issue. Just out of curiosity, may I also ask if you know why would some people connect constant 12v to power the controller when the ACC already suffices? It doesn't really need to remain on to retain memory (like the stereo) or anything right? Is it because they wanna delay the turning off of the drl after key off.
@dial2fast4 жыл бұрын
@@tzershernkhaw The reason for connecting the DRL controller to 12V constant is simply ease of install. You can connect the DRL controller red wire direct to battery +, and connect black wire to chassis ground. This way you don't have to waste time looking for ignition wire. By connecting direct to 12V constant, the DRL light will turn on only when ignition is turned on and voltage rises past 13V (does not turn on at 12V). The DRL will turn off automatically when ignition is off, and voltage drops past below 13V with a delay of about 20-30 seconds before DRL light turns off. I personally don't like having that delay in turning off the DRL (I think it looks weird and gives it an aftermarket look), so connecting to ignition 12V will give you instant on and instant off with ignition.
@tzershernkhaw4 жыл бұрын
@@dial2fast Thank you so much!!
@zmohp.20603 жыл бұрын
@@dial2fast If I connect the DRL controller red wire directly to the battery (+) and black wire to the ground, would that makes my new drl lights on even the car ignition is off?
@CheckIToutRealFast11 ай бұрын
Why do you need an LED driver for? Can’t you just connect the black wire to the negative and connect the red to an accessory fuse?
@dial2fast11 ай бұрын
Because a properly working DRL should have dual brightness. Bright for daytime, and dim for nighttime. If that's something you don't need, then connect to the ignition 12v fuse.
@CheckIToutRealFast11 ай бұрын
@@dial2fast thanks
@testdirver3 жыл бұрын
wait but that truck already have drl lol
@SpacedOdyssey26 күн бұрын
It looks as though there was DRL installed already, If so why add the extra lights
@ayamcolil3 жыл бұрын
Is any issues if I connect the DRL controller module red wire direct to battery terminal?
@LUCYDIAMONDBOXER12 жыл бұрын
I've had mine installed for a year but I had my ground wire directly into the negative port of my battery. I then placed it on a bolt inside the bay near the nearside headlamp. There's now a buzzing and clicking and they no longer come on?
@dial2fast2 жыл бұрын
That ground bolt you are using is not a good ground. You might think a metal bolt in the car is ground but not always the case because the panels on cars are glued and spot welded. Also many people don't know steel is not the best conductor compared to copper. To truly find out if the ground is good, you should use a multimeter to test the bolt. Or you can just try another ground bolt.
@LUCYDIAMONDBOXER12 жыл бұрын
@@dial2fast thanks for the reply. I'll do what you suggested. Thanks
@somerandomname92528 ай бұрын
That would be a big fat FAIL for the annual vehicle test in my country. The DRL units you fitted overhang / foul the fog lights. Obstruction of lamps designed for safety in bad weather conditions.
@zaimhilmi1033 жыл бұрын
Thank you for the nice video. Is it possible connecting the white wire through parking light fuse box tho?
@dial2fast3 жыл бұрын
You have to check with a multimeter to see if the parking light fuse in the fuse box is constant 12v or is switched on only when parking light is on.
@jashatta12 жыл бұрын
Love it but I ain’t going to do that, way above my skill level
@hassanskinner0817 Жыл бұрын
So what would happen if you decided to just hook it up to the battery?
@dial2fast Жыл бұрын
You can hook it up to ignition 12v so it turns on/off with ignition.
@hassanskinner0817 Жыл бұрын
@@dial2fast thanks
@darlaharris89012 жыл бұрын
👍🏻
@khindiep58603 жыл бұрын
hey Dial2fast, how have these lights held up? looking for a good quality set of LED DRLs. Was thinking about the philips daylight series but they are pricey.
@dial2fast3 жыл бұрын
They still work fine to this day.
@lepakistaniyat59932 жыл бұрын
Noob question, what guage wire you used for extending the connector to the left side?
@dial2fast2 жыл бұрын
Use 16 gauge or larger.
@ryanoswald55062 жыл бұрын
How, where and why do you have a ground wire when the instructions for the “iJDMTOY (1) Universal LED Daytime Running Light Automatic ON/OFF Controller Module Box Relay” doesn’t even have instructions for it? It doesn’t even show or have a ground wire. Is this a different product than the link you provided?
@ryanoswald55062 жыл бұрын
The instructions says the black wire goes to the negative terminal….
@ryanoswald55062 жыл бұрын
Hello? That was a serious question 🙋♂️
@firemandkdkdk2 жыл бұрын
@@ryanoswald5506 Negative (black) is ground on modern vehicles.......at one time back in the day , there were cars and trucks that were positive ground (red) . a GROUND simply means that everthing metal on the car ( chassis) is the negative black , or a GROUND........the black negative battery terminal is a ground .........And this is not to ever be confused with House current ( 110v/120V etc where Green is ground. if you use a black wire for ground in house current you will have a shocking experience , pun intended.
@MrPummi884 жыл бұрын
Looks like it blocks some of the fog lights.
@dial2fast4 жыл бұрын
Just a bit on the top edge of the fog. Light output still good.
@jr00g252 жыл бұрын
What did you do to the top lights?
@khmertech1678 Жыл бұрын
i got toyota pruis 2017 i still dont know how to connect it even i watched it many time
@TheNacional953 жыл бұрын
"Housing all metal" Sounds like plastic when tapped on, looks like plastic.
@randomrazr4 жыл бұрын
Wait ur car already has day time running lights.....????
@TheJustUsLeague3 жыл бұрын
yeah the pair that look like upside down check mark are the day time running lights for the pathfinder but he did say if you want an extra pair or if your vehicle did not come with any at all. But you're correct the pathfinder already has day time running lights equipped.
@jakobduke65894 жыл бұрын
Fourth one
@CheckIToutRealFast8 ай бұрын
Instead of putting it as a ground, can’t you just put it on the negative terminal?
@dial2fast8 ай бұрын
Yes you can.
@281026502 жыл бұрын
I wish that I had seen this before I purchased my DRLs and the controller. I didn’t know that you could get a controller with two outputs. I’m having to make two outputs from one, or purchase a second controller. Waste of my money.
@tuoa4683 жыл бұрын
u have already the drl light xd
@diemler3206 Жыл бұрын
Hi man . I hope you will help me to find the right solution for me. I want the transformer or the regulator of the LED light, which in turn reduces the LED lighting from 100% to 50% when the light is turned on in the dark or at night. Or the organizer to buy it online if possible ❤️🫶🏻