here does the hose on the expansion tank connect to on the other side???
@darrenalvarez59872 жыл бұрын
I have the whole kit except the electrical fan, do you think it’ll be fine with the stock fan ? Or just buy the last piece ?
@DriftHQ2 жыл бұрын
Stock fan likes to blow up ! E fan or diesel BMW fan is best
@advantage43124 жыл бұрын
would this mishimoto radiator fit in a e36 318i 4 cylinder?
@DriftHQ4 жыл бұрын
No we dont believe it does
@wandiisrak93 жыл бұрын
thanks bro
@darrennagle84142 жыл бұрын
Hi I have this same system but need to bleed it can you please tell me how to do this as I'm having trouble. Is it through the level check stick I use as a bleed screw or? Thanks
@DriftHQ2 жыл бұрын
Jack up the front of the car and leave the cap off, keep refilling until there is no more bubbles. You could use a funnel for the bleeding process.
@cobymaane56484 жыл бұрын
The hose that sticks out of the expansion tank does that just vent to atmosphere?
@DriftHQ4 жыл бұрын
No the hose goes from top of the expansion tank, to top of radiator at drivers side, to bleed air out of the system
@zervexy7416 Жыл бұрын
So what about the coolant temp sensor?
@lgitsnow6425 Жыл бұрын
It looks like there’s a bolt still inserted on the side and just remove and install sensor
@vannmann95973 жыл бұрын
I cannot get the new expansion tank to line up with the original fan shroud like you did. It's too high by an inch or so. Tried playing with the bottom hose to no avail. The other small hose that runs along the top of the radiator is a bit short now, and won't reach the expansion tank like the original. I am about to go back to the original expansion tank. That would suck because it defeats the purpose of replacing both. Any ideas? Did you have to cut anything at the bottom of the fan shroud to make your tank fit correctly?
@TehVikingsOwn3 жыл бұрын
Hello Vann, Did you reuse the old shroud, or go to the Mishimoto shroud and fan setup?
@vannmann95973 жыл бұрын
@@TehVikingsOwn Hey Alex hope you doing well bud. I am still waiting for resolution from mishimoto. They are supposed to send me another one. If this doesn't solve the problem will have to go back to my plastic tank
@TehVikingsOwn3 жыл бұрын
@@vannmann9597 Gotcha, I was able to use my stock fan shroud. With just the fan shroud out of the car, and the tank, does it fit? No hoses/interference
@vannmann95973 жыл бұрын
@@TehVikingsOwn I hope the new one makes a difference I highly doubt it if their mass produced but you never know. I might have got that 1 bad 1 out of a 1000.
@vannmann95973 жыл бұрын
@@TehVikingsOwn Yes. If you compare the original with the Mishi the original sits nice & centered with room for the hose. The Mishimoto is a little larger in diameter due to the flair on the bottom inlet. It takes up all the room needed for a hose to fit around the new tank at the bottom.
@timmulyarchuk14793 жыл бұрын
How do you bleed the system with the expansion tank. having trouble
@DriftHQ2 жыл бұрын
Jack up the car and Let all the bubbles out, rev out the engine to 1.5k rpm
@timmulyarchuk14792 жыл бұрын
@@DriftHQ thanks. I figure it out
@Murdavalleyphenom Жыл бұрын
@@timmulyarchuk1479could you help me mate I can’t bleed it to save my life it just keeps bubbling with the funnel and spitting . Am I supposed to rev at 1.5k rpms
@timmulyarchuk1479 Жыл бұрын
@@Murdavalleyphenom squeeze the the top and bottom hoses