Most helpful vid so far I’m trying to rebuild xr80 top end
@davidfriday94823 жыл бұрын
How can I tell the top ring from the button if there is no n mark?
@cesarzentil44637 жыл бұрын
Hi just thought I'd say that it doesn't matter which way the ends on the oil ring sepetator are facing. You said they need to be faced up but it really doesn't matter. Just posting this to help anyone out there who's installing rings.
@cesarzentil44637 жыл бұрын
But other then that this is a great video
@grindinggearsgarage95787 жыл бұрын
Hey thanks man! I always appreciate the help!
@Fred-yk6qk4 жыл бұрын
Great video very helpful 🍻
@pedritoc.c.t.665 Жыл бұрын
Great video. I have a 92 susuki quadrunner it ran good I full trothle it when I got it running. Then came home and now no compression. It blows it back to the carburetor. Any idea what it could be?
@Doitallbros Жыл бұрын
If it blows back the air through the carburettor than you have to tack the cylinder head off and put the piston to the bottom and put it so next valve opens is air/petrol valve
@Doitallbros Жыл бұрын
It is the valves are not sync with the piston
@pedritoc.c.t.665 Жыл бұрын
@@Doitallbros ok lo buscare .
@pedritoc.c.t.665 Жыл бұрын
@@Doitallbros I meant ok I will look in to it
@toddj.82453 жыл бұрын
Are you still working on quads im in NYC brooklyn actually I have a old Suzuki LT230 GE I want to rebuild it its all running and stock and just want to basically tune up and rebuild stock
@joseherrera3202 Жыл бұрын
Excellent video
@redrider5332 жыл бұрын
the Wiseco instructions are actually confusing. The engine front points left (9 oclock) and the "center line" also goes left to right (3 oclock to 9 oclock). I assume the center line is the Piston Pin bore. That being the case the front of most atv engines point to 12 oclock or exhaust port. Not sure why Wiseco's diagram is the way it is and it creates uncertainty regarding placement
@bobbymckinney12644 жыл бұрын
On the 2 top rings are they different ,is the very top ring shiney or ticker than the 2nd one,someone said the top one is shiney and the second dark color,and maybe the 2nd is thicker?Thanks..
@chriscookey17814 жыл бұрын
Hey brow i am trying to overall a 4JB1 .i have no experience. But i would like some guidance on the rings replacement And how to set the timing thank u
@kautiondiaz61927 жыл бұрын
good video.. Is there a certain way ( meaning facing up or down) the second an third go in?
@grindinggearsgarage95787 жыл бұрын
Kaution Diaz usually the second one will. The oil seals or lower set does not matter
@dontv94074 жыл бұрын
Is it same for all 4 strokes
@Motoman714.6 жыл бұрын
I just purchased a 800 CC big bore kit from my GY6 and I'm installing the rings and I can not get the oil ring to in close into the boar I don't get why but it's not overlapping but when it's not overlapping it's sticking out too far
@jasonedwardwood5 жыл бұрын
Wiseco instructions, illustration 1, has a line running through the pic of the piston called "piston pin center line". What the hell does that mean? It's confusing. Front of the bike is exhaust.. correct?
@samuelyeet60064 жыл бұрын
Depends on your bike, some bikes have the exhaust in the front, some have them in the back
@richardbartlett40754 жыл бұрын
On illustration 1 on the orange instruction sheet - forget the arrow with the "engine front". The piston pin center line is where the wrist pin will go. So at the top of the illustration, is actually the direction towards the front of the engine or towards exhaust. The oil ring expander gap should be as shown, 90 degrees from the WRIST PIN, as the written instructions say. Not aligned with the wrist pin.
@lakhveer654 Жыл бұрын
Rings not properly visible . Please make another video. Overall good work
@bigturbosupra125 жыл бұрын
Cool
@mrbambix4 жыл бұрын
most difficult part is allways getting the darn cilinder over the piston while compressing the rings... Do you have any tips on that?
@brycewatson33874 жыл бұрын
A piston ring compressor compresses them for you before putting them in so that it slides in no problem.
@freedomlover85257 жыл бұрын
thanks very helpful. i made the mistake of buying a cheaper piston and it came with no instructions.
@grindinggearsgarage95787 жыл бұрын
awesome thanks for watching!!!!
@mikeoneal48825 жыл бұрын
Great video. Does bottom middle wavey ring have an up or down? Does it matter which way the pointed ends face when butted up next to each other?
@jordanlittle53915 жыл бұрын
he states it in vid
@mikeoneal48825 жыл бұрын
Watched again. Points facing up, got it. Thank you
@garlanddeaton20306 жыл бұрын
Will a head gasket for a different Kawasaki fit on a Kawasaki prarie
@grindinggearsgarage95786 жыл бұрын
not really sure
@liveandletlive28944 жыл бұрын
A bayou 400 yes.
@ElsaEveC6 жыл бұрын
I will try this
@keithkent62752 жыл бұрын
I was rather hoping you'd show us you actually installing the rings.
@ehabradiology2 жыл бұрын
do not use mobile camera >>> use tripode and do not move so much with your camera, it makes us dizzy
@REVOLUTIONTEAM18 жыл бұрын
Nice video man!! I also do video about motocyrcle, so if you want check my channel :D
@grindinggearsgarage95788 жыл бұрын
Of course man! Subscribing now!!!!
@techman12744 жыл бұрын
That does not compute!
@GYccUsefultips4 жыл бұрын
The poorest video i have ever seen
@tansugunal7 ай бұрын
Again a video with zero detail for ring identification.