How To Install Taran Tactical Accuguide Extended Carrier, Safety, And Bolt Release On Benelli M4.

[@brostradamus11]

This triggered my autism when you broke down the trigger group but you put it back together again good so I like and subscribed

[@GearAndGuns]

Thank you man much appreciated.

[@JosephX143X]

If I were just adding the upgraded safety would I need to break all the trigger assembly down as well. I’m not to comfortable doing that with mine but I already bought the Taran safety.

[@GearAndGuns]

@@JosephX143X no you will not have to. You can slide out the trigger assembly and immediately start on the safety replacement process without taking apart the trigger assembly. You will need a roll pin punch that fits that roll pin though otherwise you could risk damaging the roll pin and the safety might not work as smoothly.

[@MrLew1965]

Will the original Factory M4 Plastic grips just install in place of that T Pro heat shield ?/ TY

[@GearAndGuns]

Possibly. I don’t know forsure.

[@Motownbandit]

Pretty solid video! That roll pin is suppose to be tight for the safety. Its springs open to create more friction and tension. Typically you would be using a roll pin punch. Criticism, rotate your video! lol!

[@Motownbandit]

You got my sub!

[@GearAndGuns]

@@Motownbandit thanks for the sub man! Yeah I knew it was supposed to be tight but that thing was ridiculously tight in there. I didn’t know they had a specific punch for roll pins. How does the video appear on your screen? When I watch the videos I can see them in full screen vertically on my phone. Are you saying instead of upload them vertically, to upload them horizontally? Thanks for the criticism, I appreciate it. Helps me learn and provide better content for viewers.

[@Motownbandit]

@@GearAndGuns when you go full screen at the beginning of your video, muzzle points up. So essentially you can record it however you want, you just have to remember to rotate the video in post processing. As far as the roll pin punch, it has a rounded dimple on the end. You can get a RealAvid, or wheeler, or really whatever set you want. They all work the same. Some bend a little easier though. I know you paid bank for the vortex torque driver. Punches are cheap in comparison. Build your tools up and keep pumping out videos my guy! 🍻

[@GearAndGuns]

@@Motownbandit okay I understand. I’ll try that on my next videos. I appreciate the criticism. I checked out the roll pin punch set, they both look nice. This was the only time I really needed one. That vortex torque wrench is the nicest one I’ve used, only complaint is it only goes up to 50 torque pounds. Will do. Thanks man! 🤝🏼

[@Motownbandit]

The more work you start to do on firearms, if that’s what you enjoy, the more you will run across roll pins. AR platforms use them as well. On the torque drive, I haven’t seen anything go past 50 inch lbs. that’s quite a bit of toque on a bit driver.

[@mstng65flcnman]

What foregrip is that?

[@GearAndGuns]

It’s benelli m4s new updated hand guard for there new benelli m4 t pro “gen 2” model.

[@superxpro12]

The only hard part you left out! How tf do you remove the retaining c clip?

[@GearAndGuns]

I just made a separate video for that. Check my KZbin channel and you’ll find it. The title is how to remove round retainer clip or bolt release on benelli m4.

[@edwardsimeral9432]

Where did you get the hand guard ?

[@GearAndGuns]

That’s the factory hand guard that came with the t pro “gen 2” model.

[@MarcoNoPolo]

One word.... HORIZONTAL.

[@GearAndGuns]

I’m sorry I don’t understand what you mean

[@MarcoNoPolo]

@@GearAndGuns The Video orientation.

[@GearAndGuns]

@@MarcoNoPolo yeah I’m sorry man. It was the best way to close up of the gun. It works fine on my phone but maybe not great for computer

[@MarcoNoPolo]

I'm sure you're right. I watch 90%+ of everything on my computer. @@GearAndGuns

[@MarcoNoPolo]

@@GearAndGuns No worries. 👍

[@josephramieri2256]

Impossible to follow this! You keep calling thing "this" or "that", sliding things into "there". If this was supposed to be a teaching video...forget it!

[@GearAndGuns]

I did what I can man. It’s a video. You can follow it by looking what I’m doing in the video if you can’t understand what I’m saying. I don’t know all of the parts names. I’m not a big time KZbinr. It’s a better teaching video then nothing. If it didn’t help you, sorry about that. I did the best I could. I’m still learning and just doing this to help how I can while in my own process of doing this stuff.

[@lambchop6210]

​@@GearAndGuns I thought it was a solid video dude. Followed it step by step for the taran tactical safety and lifter

[@GearAndGuns]

@@lambchop6210 thank you! Still working on information presentation and overall knowledge to put out better content.

[@LosDoyerss]

Guy needs everything labeled and catalogued before install.

[@GearAndGuns]

@@LosDoyerss lol I guess so